Hoover U6616 Support Question

Find answers below for this question about Hoover U6616.
Need a Hoover U6616 manual? We have 1 online manual for this item!

Hoover Overview Questions Manuals Reviews Videos Research

Question posted by Rroderick1 on October 8th, 2011

How Do You Clean A Plugged Up Cleaner?

The person who posted this question about this Hoover product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by sheana1 on October 8th, 2011 3:32 PM

This answer was accepted by the poster of the original question.

sheana1

Member since:
October 5th, 2011

Points: 426,890

1,110
points

detach the hose to make sure there are no blockages, then take out the canister and empty it and clean it with soap and water and let it dry before using it again. take out any filters and clean them with soap or water and let them dry before replacing or you can buy a new one. this will clear any places that might be blocking the vacume

Related Hoover U6616 Manual Pages

Manual - Page 2

... of fire, electric shock, or injury: • Do not use with damaged cord or plug. Do not operate cleaner in bare feet or when wearing open toe shoes or sandals. • Do not pick ... with the cleaner. Do not allow vacuum cleaner to be used as powder. • Use extra care when cleaning on stairs. • Do not put any appliance is not working as shown. To unplug, grasp the plug, not the...

Manual - Page 3

... parts are included with owner's manual) EI F G H The accessories are packed on front of your cleaner. Wands H. Using a Phillips screw driver, tighten screws securely. Carton contents 1-1 Accessories C D A B Remove all accessories are located before plugging cord into electrical outlet. A. Hose* E. Not all parts from carton and identify each item shown. Dusting...

Manual - Page 4

... dirt cup) storage. rear wand. *available on 26. Do not change the plug in any way. 4 Self-propel feature This feature allows you . Guide cleaner carefully at voltage specified on data plate on rear wheels and push forward. Handle pet being cleaned. 2. Headlight 5. Powered hand tool 20. Furniture nozzle 8. Dirt cup 22. Dirt...

Manual - Page 5

... ; Move the brush roll control only when the handle is necessary to green. •The red light may stay on during cleaning. Note: If the cleaner is being removed by using cleaning tools; The green light will come on some models) With red and green lights (C), the 'Dirt FINDER' system alerts the user...

Manual - Page 6

.... 2-10 2-11 2-12 AUTOMATIC BRUSH ROLL ON OFF Automatic brush roll indicator (some models) When red is in carpet near baseboards and furniture. Cleaning tools When using cleaning tools, cleaner handle must be in the upright position to wand (G) by pushing it firmly onto the wand. Attach second wand or tool to activate...

Manual - Page 7

... to allow easier cleaning of the above tools. 2-19 Slide hose into slots and twist hose to attach tool cover The tool cover is recommended that have passed through the pre-filter screen. To attach hose to your vacuum cleaner, follow the instructions below. 2-18 M N Turn cleaner OFF before using the cleaner for carved furniture...

Manual - Page 8

...lid does not close completely, turn . Allow pre-filter to dry thoroughly. 3-9 How to clean filter assembly Remove dirt cup and open too far. Bottom of HEPA cartridge filter as described... free if it away from the pre-filter into cleaner cavity. Remove cartridge from the HEPA cartridge filter. The pre-filter can be removed for additional cleaning. 3-7 J K 3-8 Grasp end of cup. ...

Manual - Page 9

... into cup until a light snap is seated properly in the filtration process to return clean air to buy This cleaner uses a 12 volt, wedge base type 912 bulb, Hoover part No. 27313101. ... above top edge of dirt cup. Using a screwdriver, remove the two screws as follows: Disconnect cleaner from electrical outlet. Should you check for part No. 40110006. Removing this filter when it becomes ...

Manual - Page 10

To check the flat belt, remove bottom plate as shown with your cleaner. Replace belt if it is described below; Remove used belt Flat belt (B) operates the self-propel feature and indirectly drives the brush roll. Tighten screws securely. To maintain cleaning effectiveness, replace agitator if brushes do not touch card. The flat...

Manual - Page 11

... brush roll Grasp brush roll and fit it out. Positioning belt on outside of belt), slide back of belt over pulley and pull front of cleaner. Turn cleaner over pulley (C). Unscrew the two Phillips screws and remove belt guard (B). 11 Push other side of tool and remove bottom plate (A). 2.

Manual - Page 13

... with two ball bearings that should be lubricated periodically by : • checking the Yellow Pages under "Vacuum Cleaners - When the thermal protector activates, the cleaner will only result in North Canton for Testing and Materials (ASTM) Carpet Cleaning Effectiveness Test (ASTM Test F608). Edge groomer replacement When to replace The edge groomers, located on...

Manual - Page 14

... until the blockage is locked in upright position. • Blockage in wall plug • Check fuse or breaker. • Blown fuse/tripped breaker • Replace fuse/reset breaker. • Thermal protector activated • Allow cleaner to be removed through 3-12). C. Problem: Cleaning tools • Filter assembly not assembled properly • Ensure that dirt...