Hoover U6616 Support Question

Find answers below for this question about Hoover U6616.
Need a Hoover U6616 manual? We have 1 online manual for this item!

Hoover Overview Questions Manuals Reviews Videos Research

Question posted by hayway on August 31st, 2014

How To Check Idler Pulley For V-belt Tension

The person who posted this question about this Hoover product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by BusterDoogen on August 31st, 2014 10:44 AM

This answer was accepted by the poster of the original question.

BusterDoogen

Member since:
October 30th, 2011

Points: 28,565,397

1,100
points

Go here for the belt & how to video.

I hope this is helpful to you!

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!

Related Hoover U6616 Manual Pages

Manual - Page 2

... Service Center or Authorized Hoover Warranty Service Dealer (Depot). • Use vacuum cleaner only for warranty service of the handle as it to this appliance before... Maintenance Authorized Service 13 Cleaning Filters 8-9 Emptying Cup 7-9 Lubrication 13 Replacing Belts 10-11 Replacing Power Hand Tool Belt .12 Replacing Brush Roll 10-11 Replacing Power Hand Tool Agitator Brush Roll...

Manual - Page 7

... these home maintenance tasks as proper use if preferred. CAUTION: Very fine materials, such as dresser drawers, upholstered furniture, stairs, and baseboards. How to your vacuum cleaner, follow the instructions below. 2-18 M N Turn cleaner OFF before using the cleaner for carved furniture, table tops, books, lamps, lighting fixtures, venetian blinds, baseboards...

Manual - Page 9

...of the cleaner. Ensure that it is pushed open the door on the side of dirt cup. Check for debris accumulation by removing bottom plate (Fig. 3-18) and looking in the channels next to... HEPA cartridge filter into cup until a light snap is pushed down into place. Should you check the filters. To reattach, align hinges (O) of socket. Headlight replacement What to snap free if...

Manual - Page 10

... is described below; To check the flat belt, remove bottom plate as shown with your cleaner. Lift off bottom plate (A). 3-19 3-20 D B C Removing used belt (B) from large pulley (C) and discard. Positioning back of belt With lettering on outside of belt, slide new belt over large pulley (C) while rolling the pulley in Fig. 3-18. Warning - Replace belt if it is turned...

Manual - Page 11

... of brush roll (H) into place. Replace with lettering on belt and "snap" it so bottom faces up brush roll and slide V-belt (D) off large pulley as shown in groove (F) on brush roll Before positioning belt onto brush roll, check for a long time and is a good time to pulley. Belt may fit loosely when properly installed. 3-24 3-25...

Manual - Page 12

... agitator, making sure not to ensure that it is cracked, gouged or broken, it (see following section). 5. Remove bottom plate, belt guard and brush roll as described in Figs. 3-28 through 3-33. Remove belt from turbine pulley (F). Replace brush roll, belt guard, and bottom plate as described in Figs. 3-30 through 3-30. 3-35 F E 2. Inspect...

Manual - Page 13

... has been designed into position as follows: 1. Refer to The Hoover Company in "The belt" section (Fig.3-18). 3-37 Installing groomers Lift off both sides of lubricant could cause ...4A8, Phone: 1-800-263-6376. Do not send your cleaner by : • checking the Yellow Pages under "Vacuum Cleaners - Other performance factors include Hose Power (ASTM Test F558), Surface Litter Cleaning,...

Manual - Page 14

... Cause Possible Solution • Too much pressure being applied to a blockage in turbine channel • Remove blockage. • Broken or worn belt • Replace belt. • Low cleaner suction • Check items under bottom plate 2. Problem: Dirt inside dirt cup stops spinning Note: Heavy debris may be removed through final filter Possible cause...