Hoover U6616 Support Question
Hoover U6616 Support Question
Find answers below for this question about Hoover U6616.Need a Hoover U6616 manual? We have 1 online manual for this item!
Question posted by hayway on August 31st, 2014
How To Tell If Idler Pulley Is Working Properly?
The person who posted this question about this Hoover product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by BusterDoogen on August 31st, 2014 2:26 PM
BusterDoogen
Member since:
October 30th, 2011 Points: 28,565,407
Member since:
October 30th, 2011 Points: 28,565,407
Go here to view how to check the belt.
I hope this is helpful to you!
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Related Hoover U6616 Manual Pages
Manual - Page 2
...outdoors or on wet surfaces. • Close supervision is necessary when any appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into openings. Empty ...com
2
Important Safeguards! Do not allow vacuum cleaner to a Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot).
• Use vacuum cleaner only for warranty service of an ...
Manual - Page 4
... handle in tight places (e.g., around hooks for height of cleaner.
To move forward, push handle forward and guide cleaner away from room to install the proper outlet.
Edge groomers
6. Dirt cup latch 9. Hose rack
23. 'Dirt FINDER' display*
24. Dirt cup handle
25. To turn cleaner ON, push switch (A) up. To...
Manual - Page 7
...washed in the left to empty
It is pushed open too far. I K
J
2-17
Select proper tool
H. Cleaning tools may be seen collecting in warm water with your cleaner) The extra reach ...19
Slide hose into place. (To detach hose, reverse procedure.) Attach wands or tools to your vacuum cleaner, follow the instructions below.
2-18
M N
Turn cleaner OFF before disconnecting and connecting hose...
Manual - Page 9
... filter assembly, place large knob of HEPA cartridge filter in hole on bottom of socket.
Press door back into cup until a light snap is seated properly in the cup. Gently pull up on sides of dirt cup. Close lid and return cup to ensure that it to replace this filter, ask...
Manual - Page 10
...18
A Removing bottom plate Place handle in low position and turn cleaner over large pulley (C) while rolling the pulley in good condition. When purchasing a new belt, ask for HOOVER part No. 48414069...flat belt, remove bottom plate as shown with your cleaner. When to stretch belt onto pulley.
3-22
Replacing bottom plate Reposition bottom plate and 4 Phillips head screws.
Replacing flat...
Manual - Page 11
... part no. 38528034 (belt package part no. 40201200). Belt may fit loosely when properly installed. Unscrew the two Phillips screws and remove belt guard (B).
11 However, if ... roll
Removing brush roll Slide brush roll control (Fig. 2-9) to replace
1. Turn cleaner over pulley (C).
Replace with lettering on brush roll
Before positioning belt onto brush roll, check for debris accumulation...
Manual - Page 12
... roll, belt guard, and bottom plate as described in guard. Inspect belt to pinch brush bristles in Figs. 3-28 through 3-33. Remove belt from turbine pulley (F). Replace belt guard (B) making sure it (see following section).
5.
Grasp turbine (E) and pull firmly to last a long time and is designed to remove. 3. Remove agitator...
Manual - Page 13
... Cleaning Performance
This Hoover Cleaning Performance System is equipped with two ball bearings that should be lubricated periodically by :
• checking the Yellow Pages under "Vacuum Cleaners -
Reposition bottom plate and secure with this happens, proceed as shown. Thermal protector
An internal thermal protector has been designed into position as follows...
Manual - Page 14
... dirt does stop spinning AND there is locked in upright position.
• Blockage in Figs. 3-28, 3-29 and 3-35. Warning - Unplug cleaner when it is properly positioned. Refer to the following steps to a Hoover Factory Service Center or an Authorized Hoover Warranty Service Dealer (Depot). If blockage cannot be due to...
Similar Questions
I Have Cleaned The Brush A Ton Of Times. Sometimes It Works When I Move It Somet
(Posted by Lsarmiento88 8 months ago)
Height Adjustment Does Not Work Properly
Model #:UH70930 height adjustment does not work properly. does not raise height until setting 4
Model #:UH70930 height adjustment does not work properly. does not raise height until setting 4
(Posted by billflewelling 8 years ago)
Hoover Model U6616-900
I Would Like A Step By Step Instructions For Disassemb
Would like step by step disassembly instructions to replace the trrsion spring #38356014 which chang...
Would like step by step disassembly instructions to replace the trrsion spring #38356014 which chang...
(Posted by tatewell 11 years ago)