Hoover U6616 Support Question

Find answers below for this question about Hoover U6616.
Need a Hoover U6616 manual? We have 1 online manual for this item!

Hoover Overview Questions Manuals Reviews Videos Research

Question posted by sharphacksaw on August 26th, 2015

How To Replace Spring On Vacuum Door

The person who posted this question about this Hoover product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by TommyKervz on August 27th, 2015 3:46 AM

This answer was accepted by the poster of the original question.

TommyKervz

Member since:
January 10th, 2013

Points: 17,776,813

1,100
points

See instructions here or click here to refer to the owners manual for any possible options. If you may want to request a service manual please click here.

Hope that is helpful.
Kervz at www.satechhelp.co.za

Related Hoover U6616 Manual Pages

Manual - Page 2

...number It is not working as a handle, close door on cord or pull cord around sharp edges or ... Hoover Warranty Service Dealer (Depot). • Use vacuum cleaner only for warranty service of your cleaner. If...Replacing Belts 10-11 Replacing Power Hand Tool Belt .12 Replacing Brush Roll 10-11 Replacing Power Hand Tool Agitator Brush Roll 11-12 Replacing Edge Groomers . . . . .13 Replacing...

Manual - Page 7

... with a cloth dampened in place. Lift cup slightly and pull straight out to -reach places. It can be seen collecting in the left to your vacuum cleaner, follow the instructions below. 2-18 M N Turn cleaner OFF before using the cleaner for carved furniture, table tops, books, lamps, lighting fixtures, venetian blinds, baseboards...

Manual - Page 9

...filter. Close door. Reattaching filter door The filter door is designed with ribs (M) in dirt cup. 3-13 3-14 N O Final filter Replacing final filter The final filter assists in the cup. Press door back into ...closes (see Fig. 3-3). Should you check the filters. Close lid and return cup to replace this filter, ask for part No. 40110006. To reattach, align hinges (O) of cover ...

Manual - Page 10

...belt (B) operates the self-propel feature and indirectly drives the brush roll. Warning - Replacing flat belt Disconnect cleaner from large pulley (C) and discard. Brush roll can start suddenly...stretched, cut or broken. The agitator brush roll When to stretch belt onto pulley. 3-22 Replacing bottom plate Reposition bottom plate and 4 Phillips head screws. Lift off bottom plate (A). 3-...

Manual - Page 11

... plate (A). 2. To remove V-belt, slide back of cleaner. Ask for a long time and is not normally replaced. How to "Hard" (OFF) position. E C Inspecting V-belt The V-belt is a good time to pulley... belt), slide back of belt over pulley and pull front of belt toward groove (E) next to replace it so bottom faces up brush roll and slide V-belt (D) off large pulley as shown in Fig. ...

Manual - Page 12

...removing the bottom plate and belt guard (Figs. 3-28 and 3-29. Replacing belt When replacing belt, ask for HOOVER part No. 38528037. 1. To replace bottom plate (A), insert the four tabs on edge of bottom plate into place.... 5. With flat sides of tool. Replace with new belt. 12 3-36 H G 4. Insert brush roll through 3-30. 3-35 F ...

Manual - Page 13

... bearings that should be lubricated periodically by : • checking the Yellow Pages under "Vacuum Cleaners - Check dirt cup pre-filter, HEPA cartridge filter and secondary and final filters ...Cleaning, Hard Floor Cleaning, Edge Cleaning, Cleaning Width and Air Filtration. Edge groomer replacement When to replace The edge groomers, located on both old edge groomers and slide new edge groomers...

Manual - Page 14

... tool use : Turn cleaner OFF and disconnect from spinning without affecting cleaning performance. Remove bottom plate, belt guard and turbine as described in the system. Replace belt turbine, brush roll, belt guard and bottom plate. Problem: Cleaner won 't turn Possible Cause Possible Solution • Too much pressure being applied to be...