Hoover U6616 Support Question

Find answers below for this question about Hoover U6616.
Need a Hoover U6616 manual? We have 1 online manual for this item!

Hoover Overview Questions Manuals Reviews Videos Research

Question posted by Anonymous-26398 on April 7th, 2011

How Do I Get The Valve Spring Back In?

How do I get the %&*^(^)(^ valve spring back in? I have new arm parts. This thing is nuts!

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Hoover U6616 Manual Pages

Manual - Page 2

... from heated surfaces. • Always disconnect cord from openings, rotating agitator and other moving parts. others may reduce air flow. • Do not pull or carry by The Hoover ...to a Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot). • Use vacuum cleaner only for warranty service of the handle as powder. • Use extra care when cleaning...

Manual - Page 3

...during assembly or operation, Visit us online at the back of handle. Not all parts are packed on back of the cleaner, make sure switch is in the OFF ... before plugging cord into back of lock. Hose* E. Carton contents 1-1 Accessories C D A B Remove all parts from self-propel button. Handle section B. Wands H. 1. However, do not remove the switch lock until assembly is...

Manual - Page 7

...cup and clean the filters often. 3-2 F Dirt cup The dirt cup assembly consists of the following parts: Lid (A) Dirt Cup (B) Pre-filter (C) HEPA Cartridge Filter(D) Dirt Inlet Opening (E) While the ... secure in place. How to attach tool cover The tool cover is in the left to your vacuum cleaner, follow the instructions below. 2-18 M N Turn cleaner OFF before disconnecting and connecting hose....

Manual - Page 9

...in place Excessive force is pushed down into socket until lid closes (see Fig. 3-3). Push new bulb straight into cup until a light snap is seated properly in the channels next to the...locked in the filtration process to return clean air to the brush roll when you check for part No. 40110006. Reattaching filter door The filter door is designed with slots on assembly to ...

Manual - Page 10

... cleaner from time to time to be sure they are worn, the agitator should be required to buy When purchasing a new agitator, ask for flat belt Hoover belt part no. 38528035 (belt package part no. 40201170). Extra effort may be replaced. Move edge of a card across bottom plate while turning agitator (Fig. 3-23...

Manual - Page 11

...To remove V-belt, slide back of brush roll (H) into place. To install new belt (with Hoover belt part no. 38528034 (belt package part no. 40201200). 3-24 3-25 3-26 F D Replacing brush roll Removing brush... as described in groove (F) on side of belt toward groove (E) next to last for HOOVER part No. 48414088. 3-28 A Installing brush roll Grasp brush roll and fit it out. E ...

Manual - Page 12

...into place. 5. The belt can be replaced. 3-34 8. Replacing belt When replacing belt, ask for HOOVER part No. 38528037. 1. Inspect belt to last a long time and is cracked, gouged or broken, replace .... Replace belt guard (B) making sure it should be seen through 3-30. 3-35 F E 2. Replace with new belt. 12 3-36 H G 4. Pivot bottom plate down , slide end plates (C) of the nozzle or ...

Manual - Page 13

... the thermal protector activates, the cleaner will only result in North Canton for HOOVER part No. 39511004. Check dirt cup pre-filter, HEPA cartridge filter and secondary and final... to replace The edge groomers, located on both old edge groomers and slide new edge groomers into your cleaner to activate after following the above steps, your ...checking the Yellow Pages under "Vacuum Cleaners -

Manual - Page 14

... performance. However, if the dirt does stop spinning AND there is turned over. empty cup and clean filters if needed. 4-1 C Checking under it. Note: Electrical parts are enclosed in the system. Problem: Cleaner won 't pick up Possible cause Possible solution • Broken or worn belt • Replace belt. • Agitator brush...

Manual - Page 15

... covers the cost of the following authorized warranty service outlets. Warranty service can only be obtained by a limited one of parts only. Hoover Authorized Warranty Service Dealers (Depots). While this appliance in the U.S.A., phone 1-800-944-9200 OR visit The.... This warranty does not apply if the appliance is rendered. 1. however, if you , all labor and parts to state.