Honeywell TH6320R Support Question
Honeywell TH6320R Support Question
Find answers below for this question about Honeywell TH6320R.Need a Honeywell TH6320R manual? We have 1 online manual for this item!
Question posted by orderuse on May 11th, 2013
Honeywell Focuspro Th632r Wireless Thermostat Code Flashing E1 33
this was brand new installed today by the contractor and now shows E1 33 alternated with the temp settings. Not sure what the code means and it isn't addressed in the owners manual
Current Answers
Answer #1: Posted by tom1997 on December 26th, 2013 4:23 PM
tom1997
Member since:
December 26th, 2013 Points: 80
Member since:
December 26th, 2013 Points: 80
This error code has to do with the wiring of the air return sensor. See p 14 of the installation manual here: https://customer.honeywell.com/resources/techlit/TechLitDocuments/69-0000s/69-2091EFS.pdf
Quote:
If E1 or E appears, check error code number (right side of screen):
23 EIM does not have dual fuel capability. Replace EIM if you have fossil fuel backup heat or change Installer Setup Function 4 to ELECTRIC if you have electric backup heat (see pages 8-10).
29 Attempting to connect incompatible wireless devices.
30 Invalid zone number. Zone number must be set to zero (see page 6).
33 Check Return Air Sensor wiring. If removing the sensor permanently, press and hold the CONNECT button on the EIM for 10 seconds (until flashing orange) to clear this error code. See page 15, then pages 5-8 to reconnect wireless devices.
34 Low signal strength. Move wireless device to a different location and try again.
38 Make sure Connected light on EIM is flashing and you are 2+ feet away from EIM.
53 Thermostat is not receiving Outdoor Temperature and Outdoor Humidity:
1. Thermostat may be configured for dual fuel, compressor lockout or auxiliary lockout with no outdoor sensor. Follow Wireless Setup procedure to connect outdoor sensor to the EIM (see pages 5 and 7).
2. If E53 continues, outdoor sensor may not be communicating. Install 2 fresh AA Lithium batteries in the outdoor sensor
Related Honeywell TH6320R Manual Pages
Owner's Manual - Page 1
Operating Manual
FocusPRO® TH6320R Wireless Thermostat Termóstato inalámbrico Thermostat Sans Fil
Owner's Manual - Page 2
... pull to see page 16).
Need Help? Quick Reference Card Grasp and pull to remove batteries. For assistance with this product please visit http://yourhome.honeywell.com or call Honeywell Customer Care toll-free at a glance.
CAUTION: EQUIPMENT DAMAGE HAZARD. Copyright © 2008...
Owner's Manual - Page 3
... la página 20 • Français : voir la page 40
About your new thermostat Programming at a glance............2 Quick reference to controls ........3 Quick reference to display ..........4
Programming & Operation Set time and day 5 Fan settings (auto/on 6 System settings (heat/cool)..........7 Program schedules 8 Program schedule overrides ....10
Auto-changeover (heat/cool) ....12...
Owner's Manual - Page 4
... work or asleep (assumes you have to do is pre-programmed and ready to go to bed at 10 pm See pages 8-9
ONE-TOUCH TEMP CONTROL: You can override the program schedule at any time, and manually adjust the temperature (see pages 10-11).
2 About your new thermostat Your new thermostat is set the time and day.
Owner's Manual - Page 5
Quick reference to controls
Digital display (see page 4)
Battery holder (see page 16)
Temperature buttons Press to adjust temperature settings (see page 10-11)
Hold button Press to override programmed temperature control (see page 11) Function buttons Press to select the function displayed just above each button. (Functions change depending on the task.)
3
Owner's Manual - Page 6
...
System Heat
More
Schedule
Temperature setting (see pages 9-11)
Auxiliary heat (Only for heat pumps with auxiliary heat)
System status Heat On/Cool On (If flashing, see p. 15)
System setting Heat/Cool/Auto/Off/Em Heat (see page 7)
More Press to view outdoor climate (if outdoor sensor is installed), or to find a misplaced remote...
Owner's Manual - Page 7
...
System Heat
More
Press SET DAY, then select current day
Done
Wed
Set Day
Set Schedule
1 Press SET CLOCK/DAY/SCHEDULE, then press or to set clock.
2 Press SET DAY, then press or to select the day of week.
3 Press DONE to save.
Note: If the display flashes Set Clock, the thermostat will follow your settings for the weekday "Wake...
Owner's Manual - Page 8
Note: Options may vary depending on . If set to select Auto or On.
In "Auto" mode (the most commonly used setting), the fan runs only when the heating or cooling system is on your heating/ cooling equipment.
6 Select the fan setting
Set Clock/Day Schedule
Fan Auto
System Heat
More
Set Clock/Day Schedule
Fan System
On
Heat
More
Press FAN to "On," the fan runs continuously.
Owner's Manual - Page 9
... only the cooling system.
• Off: All systems are off. • Auto: Thermostat automatically
selects heating or cooling depending on your heating/ cooling equipment.
Compressor is locked out.
7 Select the system setting
Set Clock/Day Schedule
Fan Auto
System Heat
More
Set Clock/Day Schedule
Fan Auto
System Cool
More
Note: Options may vary...
Owner's Manual - Page 10
... they can reduce your heating/cooling expenses by as much as 33%. (See next page to use EnergyStar® program settings. EnergyStar® settings for maximum cost savings
This thermostat is pre-set to adjust times and temperatures of each time period.)
Wake
(6:00 am)
Leave
(8:00 am)
Return
(6:00 pm)
Sleep
(10:00 pm...
Owner's Manual - Page 11
... 2 and 3 for the next time period (Leave).
Note: Make sure the thermostat is set weekend time periods (Sat-Sun), then press DONE to program (Heat or Cool).
9 To adjust program schedules
Set Clock/Day Schedule
Fan Auto
System Heat
More
Done
Set
Set
Day
Schedule
Heat
Set Schedule
Setting
70 6:00 AM
°
Mon Tue Wed Thu Fri...
Owner's Manual - Page 13
... the program schedule and allows you set will override the temperature settings for all time periods. Program schedule override (permanent)
Press to permanently adjust temperature
Indoor
75 °
Heat
Setting
75 Hold
°
6:00 PM
Cancel Fan Auto
System Heat
More
Press to resume program schedule
Press HOLD to adjust the thermostat manually, as needed.
Owner's Manual - Page 14
... Auto, the thermostat automatically selects heating or cooling depending on the same day. Heat and cool settings must be at least 3 degrees apart. Auto Changeover (heat/cool)
Set Clock/Day Schedule
Fan Auto
System Auto
More
Press until screen displays "Auto"
Note: The Auto system setting may not appear, depending on how your thermostat was installed.
Owner's Manual - Page 15
... at Remote
Cancel Fan Auto
More
The optional remote control can act as a mobile thermostat, to maintain a comfortable temperature as you move from room to room.
See Remote Control Operating Manual for more information.
13 Note: The thermostat may take up to 15 seconds to respond to temperatures measured at the remote control...
Owner's Manual - Page 17
...-in compressor protection: This feature helps prevent damage to the compressor in effect, the thermostat will flash the message Cool On (or Heat On if you set.
Note: When Adaptive Intelligent Recovery is in your schedule. It allows the thermostat to "learn" how long your furnace and air conditioner take to wait for a few...
Owner's Manual - Page 18
...The warning flashes about two months before the batteries are inserted within a few minutes. Remove the battery holder and install 2 fresh AA alkaline batteries. Battery replacement (thermostat)
Press and pull to be reset. After batteries are retained in memory.
16 All other settings are installed, the thermostat will automatically restore communication with the wireless network within...
Owner's Manual - Page 19
... flashes about two months before the batteries are installed, the sensor will automatically restore communication with the wireless network within a few minutes.
17 Battery replacement (outdoor air sensor)
Remove sensor from the bracket, remove the cover and install 2 fresh AA lithium batteries. After batteries are depleted. Remove the sensor from bracket
Remove cover and install...
Owner's Manual - Page 20
... door is on . To restore power:
• Check circuit breaker and reset if necessary. • Make sure power switch at heating & cooling system is on . • Make sure furnace door is restored, the thermostat will automatically restore wireless communication within a few minutes.
18 After power is closed securely.
• Wait 5 minutes for the system...
Owner's Manual - Page 21
... damage which vary from which you . In Canada, write Retail Products ON15-02H, Honeywell Limited/Honeywell Limitée, 35 Dynamic Drive, Scarborough, Ontario M1V4Z9. Customer Care will make the determination whether the product should be returned to the following address: Honeywell Return Goods, Dock 4 MN10-3860, 1885 Douglas Dr. N., Golden Valley, MN 55422, or...
Owner's Manual - Page 64
...Pour obtenir de l'assistance concernant ce produit, visitez http://yourhome.honeywell.com ou appelez gratuitement l'assistance client d'Honeywell au 1-800-468-1502
Automation and Control Solutions
Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 http://yourhome.honeywell.com
Honeywell Limited-Honeywell Limitée 35 Dynamic Drive Scarborough, Ontario M1V 4Z9
69...
Similar Questions
Blower Fan Wont Turn Off Despite No Heat Or Cool Being Commanded
we have a new 2 stage keeprite Air to Air heat pump with aux backup. Honeywell th6320r wireless ther...
we have a new 2 stage keeprite Air to Air heat pump with aux backup. Honeywell th6320r wireless ther...
(Posted by efsharpe 9 years ago)
What Does The Error Code E1-33 Mean
want to know error code e1 -33 mean on th6320r honeywell thermostat
want to know error code e1 -33 mean on th6320r honeywell thermostat
(Posted by Anonymous-148705 9 years ago)
A/C Never Turns Off
Had a new furnace and ac put in this month. The wireless thermostat is set at 71it reached 71 this m...
Had a new furnace and ac put in this month. The wireless thermostat is set at 71it reached 71 this m...
(Posted by burralayna 9 years ago)
Why Is The Honeywell Focuspro 5000 Digital Thermostat Blinking Cool On
(Posted by bobalta 9 years ago)
I Do Not Know How To Program The Thermostat, I Need To Change The Temp Setting.
I have a T7351F2010 thermostat....I do not know how to program it. Is there a factory set code? My l...
I have a T7351F2010 thermostat....I do not know how to program it. Is there a factory set code? My l...
(Posted by usertoni8203 12 years ago)