Honeywell MK9535-79C5M38 Support Question
Honeywell MK9535-79C5M38 Support Question
Find answers below for this question about Honeywell MK9535-79C5M38 - Metrologic MS9535 VoyagerBT.Need a Honeywell MK9535-79C5M38 manual? We have 1 online manual for this item!
Question posted by gowriepl on March 4th, 2013
Scanner Won't Work
The dock's blue light is on and the blue and white lights come on, along with the red laser light when I first put the scanner onto the dock. The amber light is also on when the scanner is sitting on the dock. However, when I pick it up to scan library books, it is dead.
Current Answers
Related Honeywell MK9535-79C5M38 Manual Pages
User Guide - Page 1
MS9535 VoyagerBT Wireless Hand-Held Laser Scanner
Installation and User's Guide METROLOGIC INSTRUMENTS, INC.
User Guide - Page 3
... Floor Singapore 416186
Metro (Suzhou) Technologies Co., Ltd. 221 Xing Hai Street Suzhou Industrial Park Suzhou, China 215021
Metrologic Japan Co., Ltd. Products and brand names mentioned in the Copyright Act of this work may quote brief passages in a review, or provided for in this document are trademarks of their respective companies...
User Guide - Page 5
INTRODUCTION
MS9535 VoyagerBT laser bar code scanner is a new member of the VoyagerBT also works as a battery charger for the scanner. Before normal scanning, the scanner must establish communications with its cradle. The cradle of Metrologic's Voyager series. When resting in 2.5 hours. For power saving, the scanner can reach a fully charged state in the cradle, the scanner ...
User Guide - Page 6
... States
Communication Cable
54-54000B-N RS232 / Light Pen Cable, short strain relief
57-57002A
...SCANNER AND ACCESSORIES
Part #
BASIC KIT Description
MS9535-5 70-79004 00-02544B
VoyagerBT Scanner
MS9535 VoyagerBT Wireless Hand Held Laser Scanner Installation and User's Guide*
MetroSelect Single-Line Programming Guide*
00-02024A
Bluetooth Programming Addendum
* Available on the Metrologic...
User Guide - Page 8
r
MS9535 VoyagerBT also provides two modes of the cradle will beep once and flash the white LED. While in this mode, present a bar code in the scanning ...data is only decoded and transmitted when the CodeGate button is in CodeGate mode. MS9535 is shipped from the cradle. The blue LED of operation: 1. The scanner will also flash once, indicating that the bar code has been successfully read ...
User Guide - Page 10
...termination exposed for connecting to EN 60950. The blue LED on the other . The keyboard wedge cable...connector on one end and a 6-pin mini DIN female connector on .
5.
Metrologic will supply an adapter cable with standard CSA C22.2 No. 950/UL 1950 and...terminated with applicable standards, all circuits connected to the scanner must meet applicable performance requirements for SELV ( Safety...
User Guide - Page 15
... Identifier
14
Communication Protocol(s) Full RS-232
MI9535-5xx
41
RS-232 / Light Pen Emulation
MI9535-5xx
47
Keyboard Wedge, Stand-Alone Keyboard Wedge and RS-... in various configurations. RECEIVER / CHARGER CRADLE
The cradle of MS9535 works both as a receiver and a charger. To communicate with MLPN #46-46772.
11
Even if the scanner's battery is set into place. As a receiver, after ...
User Guide - Page 17
SCANNER PARTS
White LED Blue LED
Output Window
Amber LED CodeGate Button
MS9535 Top View MS9535 Top View
Plastic Feet/ Charge Contacts
MS9535 Side View
13
User Guide - Page 19
... the data to accept the information, the scanner's white LED will stay on after a short delay. Steady Blue and Single White Flash When the scanner successfully reads a bar code, the white LED will flash, the blue LED remains steady and the scanner will flash. VISUAL INDICATORS
The MS9535 has three LED indicators (blue, white and amber) located on the head of the...
User Guide - Page 20
... and is out of the scanner becomes full. Flashing Amber If the scanner is in cradle, this indicates the scanner is still waiting for communication from the cradle.
Steady White, Blue off This indicates the laser is off and the scanner is being charged. VISUAL INDICATORS (CONTINUED)
Alternating Flashing of Blue and White This indicates the scanner is in RangeGate active...
User Guide - Page 22
... desired scanner options. This program can be downloaded for FREE from Metrologic's website (www.metrologic.com).
¾ MetroSet2
This user-friendly Windows-based configuration program allows you to these guides for FREE from Metrologic's website (www.metrologic.com), or set-up disks can be configured by calling 1-800-ID-METRO.
18 PROGRAMMING MODES
The MS9535 VoyagerBT has...
User Guide - Page 23
... file is ready to a new or custom version of Flashbased scanners. The program guides the user with its current location. In other words, all RS232/Light Pen (-41), keyboard wedge (-47), USB (-07) and IBM 468X/469X (-11) units can be supplied by Metrologic in the upgrade. These files contain all units, an...
User Guide - Page 27
... devices. CONNECTING TO OTHER BLUETOOTH DEVICES
Other than the cradle, the MS9535 VoyagerBT scanner can also link to establish the communication.
³ 0 0 0CA7...Without FNC3
23 A Bluetooth communication between the scanner and the other device must be established before the system works. ¾ When MS9535 acts as Client:
The MS9535 is established by scanning the Bluetooth address code...
User Guide - Page 28
... establish communication directly with a Bluetooth enabled device, bypassing the cradle.
³ 0 0 0CA7 0 0 0 0 0 0 Provide service to the scanner and attempt communication. CONNECTING WITH OTHER BLUETOOTH DEVICE (CONTINUED)
¾ When MS9535 acts as Server: To enable the MS9535 to act as a server and to be discovered by another Bluetooth device, scan the below Provide Service...
User Guide - Page 29
... up
VLD failure
Contact a Metrologic Representative
Razz tone, blue and white LEDs flash at power up
Possible ROM failure Flash ROM Upgrade Required
Non-volatile RAM failure
Contact a Metrologic Representative, if the unit will not function. Make sure the cable is for reference purposes only.
No LEDs, beep, or laser Scanner out of Cradle
Internal battery...
User Guide - Page 31
... length setting does not work with the bar code
Check if the correct minimum symbol length is set properly. change to detect whether the PC is operating in Caps Lock mode
Enable Caps Lock detect setting of printer could be the problem.
Adjust inter-character delay symptom. Scanner beeps at some bar...
User Guide - Page 32
Everything works except for a couple of the scanner and the communication port match and the program is looking for the same interface parameters
Characters...not communicate properly to the host
Com port at the host is not working or configured properly
Check to make sure that the baud rate and parity of the scanner and the communication port match and the program is looking for "RS-...
User Guide - Page 33
...Light Levels: Up to 4842 Lux (450 footcandles)
Shock: Designed to withstand 1.5 m (5') drops
Contaminants: Sealed to scan; Amber = battery full
Length: 198 mm (7.8")
Width: Handle - 45 mm (1.8"), Head - 78 mm (3.1")
Depth: 40 mm (1.6")
Weight: Scanner... (LED) Default Settings:
MECHANICAL
Blue = laser on, ready to resist airborne particulate contaminants
Ventilation: None required
29...
User Guide - Page 42
... sole option, repair the Product or replace the Product with all MS9535 scanners are manufactured by anyone other than Metrologic's repair department or authorized repair centers. To do this, contact Metrologic's Customer Service/Repair Department to the Metrologic facility in the sole judgement of Metrologic, has been subjected to abuse, misuse, neglect improper installation, or accident...
User Guide - Page 45
...and restrictions therein. D408,532; PATENTS
Patent Coverage The VoyagerBT METROLOGIC product may be covered by or contained in the METROLOGIC products that are currently pending.
41 No license right or... intended use of the specific equipment, circuits, and devices represented by one or more of METROLOGIC's license rights and subject to the extent of the following US Patents: US Patent No....
Similar Questions
Scanner Not Scanning
While the scanner is on the stand there is constantly yellow light but when we try to scan the item ...
While the scanner is on the stand there is constantly yellow light but when we try to scan the item ...
(Posted by Anonymous-143026 9 years ago)
My Scan Metrologic Can Not Read The Bag Code
Who can i find the guide to setup my scan metrologic MS9535, every thing is ok, but i think is block...
Who can i find the guide to setup my scan metrologic MS9535, every thing is ok, but i think is block...
(Posted by gevost19 11 years ago)
3800g Adaptus Scanner Mulfunction
why does my scanner not display the scan results (prices)? it was working fine and it had never fel...
why does my scanner not display the scan results (prices)? it was working fine and it had never fel...
(Posted by abnarmoepi 11 years ago)
Sleep Modes Ms9535
CAn MS9535 return from sleep mode just by shaking it?
CAn MS9535 return from sleep mode just by shaking it?
(Posted by vmarquezc 11 years ago)
Scanner Won't Work!
My Adaptus 3800g, s/n 10200d09e0 worked fine on XP desktop until the desktop broke. I have reloaded ...
My Adaptus 3800g, s/n 10200d09e0 worked fine on XP desktop until the desktop broke. I have reloaded ...
(Posted by rhondajohnson 11 years ago)