Hitachi c15fb Support Question
Hitachi c15fb Support Question
Find answers below for this question about Hitachi c15fb - 15 Amp Miter Saw No Bevel.Need a Hitachi c15fb manual? We have 1 online manual for this item!
Question posted by delliott49 on April 2nd, 2017
Wiring Diagram For Hitachi Miter Saw
I bought a switch for Hitachi c10 fc2 & need a wiring diagram to hook it upThank You Dave
Current Answers
Answer #1: Posted by hzplj9 on April 4th, 2017 12:26 PM
hzplj9
Member since:
June 25th, 2012 Points: 4,873,510
Member since:
June 25th, 2012 Points: 4,873,510
This could be what you are looking for:
https://www.manualslib.com/manual/411509/Hitachi-C15fb-15-Amp-Miter-Saw-No-Bevel.html
It has the wiring diagram etc.
Related Hitachi c15fb Manual Pages
User Manual - Page 1
... correspond to the item numbers in the Parts List and exploded assembly diagram. [CAUTION] Prior to commencing disassembly (including replacement of the saw blade), ensure that the
plug is disconnected from the rear portion of the Base and Turn Table:
Tools Required:
• 17 mm Box Spanner
A. Disassembly: (1) Disassembly of the Base Ass...
User Manual - Page 2
...15] and four D5 x 90 -Hd. B. Tapping Screws [13] it in the Set Pin [97] to engage the Grip [100]). Being very careful as cautioned above, release the fixing device (Set Pin [97] and Grip [100]) and slowly and carefully raise the Gear Case [53]. (2) Disassembly of the Saw Cover Section: Tools... Required:
• Plus Screwdriver
The Saw Cover Ass'y...
User Manual - Page 3
... Ass'y [3] by following the disassembly procedures in paragraph (3), above. Screws [74], gently tap on the saw cover side of the Switch and Handle Section: Tools Required:
• Plus Screwdriver
A. Tapping Screws [21], the Switch [22] can be taken out.
After loosening the three M6 x 25 Flat Hd. Then loosen the two M5 x 12 -Hd...
User Manual - Page 4
...the wires as possible. B. (6) Disassembly of the Stator Ass'y: A. Remove the two Brush Caps [55] from the Brush Holders [56]. Disassembly of the Armature Ass'y and Stator Ass'y: Tools Required:... Stator Ass'y [46].
1-2. Remove the Saw Cover Ass'y [3] and handle Cover [25] by following
tests:
--- 4 --- B. Remove the Armature Ass'y [36] from the Switch [22]. Loosen the two D4 x 10...
User Manual - Page 5
...tightened properly to the polycarbonate portion of the Switch Handle.
(3) If the M12 Nut and M12 Lock Nut on the Hinge, causing uneven cutting of the Saw Blade (or Dummy Disc) and Vise ...onto the Hinge [119], and temporarily fix the Hinge
onto the Turn Table [87] with the main switch turned ON. If they are not tightened sufficiently, the Gear Case may interfere with the smooth movement of...
User Manual - Page 6
...Saw Blade, and perform adjustment with the 0˚ setting of the Switch. In particular, carefully confirm that it does not come in accordance with the Turn Table.
(3) Saw...Saw Blade
reassembled, adjust the M10 x 40 Bolt [95] without fail to set the height in contact
with cutting
needs... are no exposed wire cores at 0˚ Scale Setting
185 mm
Saw Blade
185 mm
Saw Blade
(Point A)...
User Manual - Page 7
and Canada Only):
WIRING DIAGRAM
Armature Ass'y
Stator Ass'y
Switch Black
Brown
White
White Connector
Cord
LEADWIRE ARRANGEMENT
Noise Suppressor Connector
Switch
Tube (A)
Cord Cord Armor
--- 7 --- Wiring Diagrams and Leadwire Arrangements: Perform wiring work as illustrated below. (1) For Products with a Dynamic Brake (115V Specification Products for the U.S. 1-5.
User Manual - Page 8
(2) For Products with a Noise Suppressor: [NOTE] The wiring diagram for products without a Noise Suppressor is the same as that illustrated below with the
exception of the Noise Suppressor section. WIRING DIAGRAM
Armature Ass'y
Stator Ass'y
LEADWIRE ARRANGEMENT
Noise Suppressor
Switch
Vinyl Tube
Black Red
Black
Red
Green
Terminal (w/o insulation tube)
M5 x 75 Machine Screw Stator Core...
User Manual - Page 9
...15 seconds.
• Use a Tungsten Carbide Tipped
Saw Blade for material ...numbers in the Parts List and exploded
assembly diagram.
(All Dimensions in inaccurate angles. Within...Saw Blade to cut surface.) (Mitered joints cannot be
A.
Inaccurate cutting. (Unable to ensure proper
uneven cutting. Improper perpendicularity between Vise (B) [82] and the Base Ass'y [103] causes inclined bevel...
User Manual - Page 10
... wood or aluminum (Code No. 959024) is recommended.)
B.
C. Improper perpendicularity between Saw Blade and Turn Table [87] causes Saw Blade to cut surface.) (Mitered joints cannot be accurately aligned.)
2. E.
When the Saw Blade cuts
---- Fig. 7
Workpiece
--- 10 --- The workpiece is 10 --- 15
seconds.)
H.
With Grain (Smooth cutting surface)
... Plane the surface of...
User Manual - Page 11
Vise (A) [79].
curely fixed in position with
ly fixed in position. (The Ball
Index Settings at 0˚, 15˚, 22.5˚,
30˚ and 45˚ are affected by
vibration, and are not sufficient to remove defects, and recheck the cutting.
Excessive vibration ...
Similar Questions
How To Square A Hitachi Miter Saw
(Posted by prisibr 10 years ago)
Need Additional Specs For The Hitachi 15' C15fb
Will it cut 6-5/8" schedule 40 black plastic pipe? What is the measurement from the bottom of the b...
Will it cut 6-5/8" schedule 40 black plastic pipe? What is the measurement from the bottom of the b...
(Posted by toolgirl 12 years ago)
I Have A New Switch For My Hitachi C15fb I Need A Diagram To Rewire It
(Posted by luicha 12 years ago)
Hitachi C15fb Miter Saw
How do I remove the hinge shaft to replpace the springe? It looks like it can be forced out.
How do I remove the hinge shaft to replpace the springe? It looks like it can be forced out.
(Posted by edmahoney 12 years ago)