Hitachi c15fb Support Question
Hitachi c15fb Support Question
Find answers below for this question about Hitachi c15fb - 15 Amp Miter Saw No Bevel.Need a Hitachi c15fb manual? We have 1 online manual for this item!
Question posted by toolgirl on February 7th, 2012
Need Additional Specs For The Hitachi 15' C15fb
Will it cut 6-5/8" schedule 40 black plastic pipe?
What is the measurement from the bottom of the blade to the surface it is mounted to?
What is the measurement from the blade to the bottom of the arbor washer?
Thank you
Current Answers
Related Hitachi c15fb Manual Pages
User Manual - Page 1
...When removing the Hinge [119], be very careful not to commencing disassembly (including replacement of the saw blade), ensure that the
plug is disconnected from the main body.
B. Machine Screws [127]. The ... portion of the Base and Turn Table:
Tools Required:
• 17 mm Box Spanner
A. C. Remove the two M6 x 16 -Hd. Remove the four M10 x 40 Bolts [66] which fix the Hinge [...
User Manual - Page 2
... Nut [93]. Machine Screws [15] and four D5 x 90 ...Tools Required:
• Plus Screwdriver
The Saw Cover Ass'y [3] can be disassembled by removing the M4 x 10 -Hd. Insert screwdriver through the holes at all times. Loosen the M10 Lock Nut [96], and screw the M10 x 40...Saw Cover which indicates the rotational direction of the saw blade.
(2) Disassembly of the four D5 x 90 -Hd. E.
User Manual - Page 3
...the Spindle Section and stopper Pin: Tools Required:
• Plus Screwdriver, Pliers, Wooden or Plastic Hammer
A.
The Handle [20] ...can be disassembled, first loosen the two M5 x 20 -Hd. When only the Switch [22] must be taken out. B.
Then loosen the two M5 x 12 -Hd. Screws [74], gently tap on the saw cover side of the Switch and Handle Section: Tools...
User Manual - Page 4
...and Stator Ass'y: Tools Required:
• Plus Screwdriver, Nippers, Wooden or Plastic Hammer
1. Machine Screws... [48] which fix the Stator Ass'y [46]. C. Tapping Screws [41], and remove the Tail Cover [42] from the Housing Ass'y [84], and take out the two Carbon Brushes [40]. Remove the Saw...mounting end of the Housing Ass'y [84] to loosen and remove the ...
User Manual - Page 5
... in excess of 7 megohms.
B. B. Then thoroughly tighten the four M10 x 40 Bolts [66]. Table Insert Mounting Groove
Turn Table
Position Saw Blade (or Dummy Disc) in excess of 1.2 mm, and ensure that the Saw Blade (or Dummy Disc) is positioned exactly in the Base Ass'y [103]. Mount the D12.7 Steel Ball [117] and Spring (C) [118] onto the...
User Manual - Page 6
... the insulation covering than is properly aligned with the M10 x 40 Bolt [95] so that the appropriate dimension between the Handle and Handle Cover during reassembly.
--- 6 --- In addition, carefully avoid pinching leadwires between the surface of Vise (B) and Point A (where the Saw Blade intersects the surface of the above
Workpiece
H
the Turn Table for the operator...
User Manual - Page 7
Wiring Diagrams and Leadwire Arrangements: Perform wiring work as illustrated below. (1) For Products with a Dynamic Brake (115V Specification Products for the U.S. 1-5. and Canada Only):
WIRING DIAGRAM
Armature Ass'y
Stator Ass'y
Switch Black
Brown
White
White Connector
Cord
LEADWIRE ARRANGEMENT
Noise Suppressor Connector
Switch
Tube (A)
Cord Cord Armor
--- 7 ---
User Manual - Page 8
... as that illustrated below with the
exception of the Noise Suppressor section. WIRING DIAGRAM
Armature Ass'y
Stator Ass'y
LEADWIRE ARRANGEMENT
Noise Suppressor
Switch
Vinyl Tube
Black Red
Black
Red
Green
Terminal (w/o insulation tube)
M5 x 75 Machine Screw Stator Core
Noise Suppressor Yellow/Green
Connector
--- 8 ---
User Manual - Page 9
... turn
etc.) in inaccurate angles. Improper perpendicularity between Saw Blade and Turn Table [87] causes Saw Blade to cut surface.) (Mitered joints cannot be
A.
movement of the Saw Blade. (Excessive vibration)
0.26/φ 370 (With Dummy Disc)
• Replace the Saw Blade. • Replace Washer (A) [28] and/or
Washer (B) [29]. num (Code No. 959024).
Excessive looseness or...
User Manual - Page 10
...rough cutting surfaces
A = 0.02/60 Fig. 5
Fig. 6: Left Bevel Cutting Fig. 7: Right Bevel Cutting
Possible Cause (s)
Standard
Countermeasure (s)
J.
piece to remove defects, and
recheck the cutting accuracy.
Improper perpendicularity between Saw Blade and Turn Table [87] causes Saw Blade to cut surface.) (Mitered joints cannot be accurately aligned.)
2.
Reduce cutting operation...
User Manual - Page 11
... (s)
I. Handle [116] without fail to fix the
Turn Table in rough cutting surfaces.
Curved or rough surface of Possible Causes A, B, D, J and K, above . curely fixed in position with
ly fixed in Item 1. Item
Phenomenon
Cutting operation results in position. (The Ball
Index Settings at 0˚, 15˚, 22.5˚,
30˚ and 45˚ are affected...
Similar Questions
Wiring Diagram For Hitachi Miter Saw
I bought a switch for Hitachi c10 fc2 & need a wiring diagram to hook it upThank You Dave
I bought a switch for Hitachi c10 fc2 & need a wiring diagram to hook it upThank You Dave
(Posted by delliott49 7 years ago)
How To Square A Hitachi Miter Saw
(Posted by prisibr 10 years ago)
I Have A New Switch For My Hitachi C15fb I Need A Diagram To Rewire It
(Posted by luicha 12 years ago)
Hitachi C15fb Miter Saw
How do I remove the hinge shaft to replpace the springe? It looks like it can be forced out.
How do I remove the hinge shaft to replpace the springe? It looks like it can be forced out.
(Posted by edmahoney 12 years ago)