Hitachi C10FCE2 Support Question
Hitachi C10FCE2 Support Question
Find answers below for this question about Hitachi C10FCE2 - 10 Inch Compound Miter Saw.Need a Hitachi C10FCE2 manual? We have 2 online manuals for this item!
Question posted by prisibr on January 21st, 2014
How To Square A Hitachi Miter Saw
The person who posted this question about this Hitachi product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Hitachi C10FCE2 Manual Pages
Operating Instructions - Page 3
...HITACHI. Never use this Instruction Manual. Always keep the work area. Never force a tool or an attachment to do the job better and more safely if it is turned on the power tool and in this power tool... a potentially hazardous situations which may cause machine damage. Always unplug unattended tools and keep the work
benches.
4. Wear protective hair covering to prevent bodily...
Operating Instructions - Page 4
...in order to provide support for Use of the slide
compound saw blade.
17. Always check the
guard and all moving parts for this tool, use outboard stands to avoid injury:
DO's
ALWAYS OBSERVE...cutting operation produces dust.
10. Always unplug the power cord when the tool is in place. Applying the wrong voltage or applying DC power can cause the
POWER TOOL to operate improperly and ...
Operating Instructions - Page 5
...tool while wearing loose clothing, a necktie or jewelry, or while your hands out of the path of the
compound saw blade, always confirm that it
might be hazardous. 9. Always confirm that overhang the table of the saw blade. 15. During miter... smoothly before using the tool. 10. When replacing the saw .
22. Always make a trial run first before starting the tool.
18. Always confirm ...
Operating Instructions - Page 6
...TOOL near flammable liquids or gases because sparking can cause an explosion. 15. Never operate the saw blade. 6. Always wear eye protection when using the compound saw without the guards in damp locations. 22. No load speed is 10... Saw blade diameter is 5000/min. 10.
Repairs should be conducted only by a Hitachi authorized service center.
6 Always turn on this could cause the saw...
Operating Instructions - Page 7
...: Avoid electrical shock hazard. Ampere Rating
More
Not More
Than
Than
0 - 6
6 - 10
10 - 12
12 - 16
MINIMUM GAGE FOR CORD SETS
Total Length of power and overheating. Inspect...the double insulation system effective, follow the normal electrical safety precautions given in this power tool, HITACHI has adopted a double insulation design. If in wet environments. The smaller the gage ...
Operating Instructions - Page 8
... the power tool. NAME OF PARTS
MODEL C10FCH/MODEL C10FCE
Dust Bag
Motor Head Gear Case
Handle Motor
Saw Blade
Laser Marker (Only C10FCH) Vise Assembly
Fence (B)
Turntable
Lower Guard
Rotation Direction
Indicator (B) (For bevel scale) Fence (A)
Table Insert Indicator (A) (For miter scale)
Lever...Instruction Manual may show details or attachments that differ from those on your own power tool.
Operating Instructions - Page 9
English
SPECIFICATIONS
Item
Model
C 10FCH / C 10FCE
Motor
Type
Series commutator motor
Power source
Single-phase AC 60Hz
Voltage (Volts)
120
Full-load current (Amp)
15
Laser Marker Maximum output
Operating Instructions - Page 11
... dust bag and vise assembly as that specified on the nameplate of the same
voltage as indicated in the section on the saw blade spindle to the retract position before using the power tool (see Fig. 33-a, Fig. 33-b, Fig. 33-c and Fig. 33-d in Fig. 1 and Fig. 2. Never connect this power...
Operating Instructions - Page 12
... is standing behind, the power tool start and confirm that no operating abnormalities exist before attempting a cutting operation.
10. otherwise the workpiece
might occur...tool's power cord is damaged. Repair or replace the power cord if an inspection indicates that the power cord plug fits properly in Fig. 9, use a steel square for deflection to the fence;
Make sure the end of the saw...
Operating Instructions - Page 13
...wing bolt as the power plug is pulled inadvertently, the saw blade can realize stable cutting of the material with the ...in Fig. 10.
6mm Wing Nut (Optional accessory)
Move
6mm Wing Bolt (Optional accessory)
Height Adjustment Bolt 6mm (Optional accessory)
Fig. 10
5. CAUTION... , It will contact the blade or some part of the tool, causing in lengths of direct angle cutting and angle cutting, ...
Operating Instructions - Page 17
...injury always firmly tighten the miter handle.
5. Starting from the workpiece. For maximum dimensions for compound cutting, refer to the right for compound cutting.
use of the tool without pulling back, causes...or with the side handle not properly
tightened, will come to contact the saw blade is secured on the miter scale (Fig. 22).
(2) Re-tighten the side handle to scatter about...
Operating Instructions - Page 18
...) contacts the fence as in Fig. 25 (see Fig. 25.
Then tighten the clamp lever. Miter Angle Setting
Bevel Angle Setting
right 35.3° ( mark)
left 30° ( mark)
right 31....6° ( mark)
2 Tilt the motor head to cut crown moldings at positions 1 and 4 in Fig. 36. Miter Angle Setting
Bevel Angle Setting
left 35.3° ( mark)
left 30° ( mark)
left 31.6° ( mark...
Operating Instructions - Page 19
...Fig. 26
Fence
Base
2 Fence
Fence
Head Bevel Angle Scale 3
Base Turntable Miter Angle Scale Fig. 27
English
Table on Base
Table on either the left fence ... Bolt
(Optional accessories)
easier cuts of the crown molding. a. Do not bevel cutting.
The main body or saw blade. After inserting Tighten the 6mm knob bolts to secure the crown molding Stoppers.
19 Then turn the upper knob...
Operating Instructions - Page 20
...it before it to the right as shown in Fig. 32.
SAW BLADE MOUNTING AND DISMOUNTING
WARNING: * To prevent an accident or ... such as shown in the lateral direction, and clamp it using tools other than normal during bevel cutting. Fig. 32
CAUTION: Empty ...from becoming
clogged. Duct Right Angle
Base
(2) During bevel and compound cutting, attach the dust bag at a right angle to prevent...
Operating Instructions - Page 21
... washer (D) and the bolt, and install them onto the saw blades larger than 10" (255mm) in paragraph 1 above. Dismounting the saw blade
Dismount the saw blade by the tool handle tends to increase, making it to install saw blade spindle.
5/8" (15.9mm)
10mm Box Wrench
6mm Bolt Washer (D)
Saw Blade Bolt Washer
Fig. 33-c
Washer (D) (Chamfering side...
Operating Instructions - Page 22
...motor are loose, align the sides of the tool, test the lower guard (see Fig. 36) with the steel square. Never use the tool unless the lower guard operates properly and it ...Fig. 35.
Groove for looseness. After adjusting the saw blade with a slotted
(minus) screwdriver. WARNING: To prevent personal injury, never operate the power tool if any loose part.
The carbon brushes can result...
Operating Instructions - Page 23
...that only authorized replacement parts will be performed by an AUTHORIZED HITACHI POWER TOOL REPAIR CENTER ONLY. NOTE: Specifications are subject to keep the power tool in good operating condition for a long time (see Fig... of the lower guard with soapy water, etc.
To avoid a malfunction of HITACHI.
23 English
8. Lubrication
Lubricate the following sliding surfaces once a month to change...
Parts List - Page 1
Hitachi Power Tools
LIST NO. E946
ELECTRIC TOOL PARTS LIST
COMPOUND SAW Model C 10FCE2
2006 • 10 • 11 (E1)
4 5 6 7
13 14
46 47 48 49 50
3
9 8
12 11
10
22 23 24 25 26
21
15 16
39 40 41 42 43 44 45
18 19 20
38
27 28 29
53 54
55
...
Parts List - Page 4
...102 319-107 TCT SAW BLADE 255MM-D30 HOLE-NT30 1
* 102 319-106 TCT SAW BLADE 255MM-D25.4 HOLE-NT24 1
* 102 318-963 TCT SAW BLADE 255MM-D15.88 HOLE-NT24 1
* 102 318-964 TCT SAW BLADE 255MM-D25.4 ...WASHER) M5X16 2
115 949-819 HEX. SOCKET HD. SCREW M6X16 (10 PCS.)
1
118 949-217 MACHINE SCREW M4X12 (10 PCS.)
1
119 949-429 BOLT WASHER M4 (10 PCS.)
1
120 322-920 HOOK
1
121 326-708 HANDLE
1
...
Parts List - Page 7
...
629 322-710 GUIDE ASS'Y
1 INCLUD. 615, 619, 626, 627
* 630 976-472 TCT SAW BLADE CROSS-CUT 255MM-D15.9 HOLE 1 FOR USA, CAN
* 631 319-658 TCT SAW BLADE 255MM-D15.88 HOLE-NT100 1 FOR USA, CAN
C 10FCE2
10 -- 06
* ALTERNATIVE PARTS
--- 7 ---
DESCRIPTION
501 940-543 BOX WRENCH 10MM
502 949-695...
Similar Questions
C10fs Compound Miter Saw Bearing Replacement
how do I remove the bearing from the armature
how do I remove the bearing from the armature
(Posted by Bobster8820 3 years ago)
Wiring Diagram For Hitachi Miter Saw
I bought a switch for Hitachi c10 fc2 & need a wiring diagram to hook it upThank You Dave
I bought a switch for Hitachi c10 fc2 & need a wiring diagram to hook it upThank You Dave
(Posted by delliott49 7 years ago)
326-700 This Part Has Been Discontinued. I Need A Replacement For This Part.
I need a replacement for this part, it has been discontinued . My Hitachi Miter saw C10FCE2 the swit...
I need a replacement for this part, it has been discontinued . My Hitachi Miter saw C10FCE2 the swit...
(Posted by TXpallets 9 years ago)
How To Square The Head On An Hitachi Miter Saw
(Posted by afajab 9 years ago)
How To Adjust Cut Depth Hitachi 10 Compound Miter Saw Manual
(Posted by dbrag 9 years ago)