Hitachi C10FCE2 Support Question
Hitachi C10FCE2 Support Question
Find answers below for this question about Hitachi C10FCE2 - 10 Inch Compound Miter Saw.Need a Hitachi C10FCE2 manual? We have 2 online manuals for this item!
Question posted by TXpallets on February 11th, 2015
326-700 This Part Has Been Discontinued. I Need A Replacement For This Part.
I need a replacement for this part, it has been discontinued . My Hitachi Miter saw C10FCE2 the switch is not working anymore.
Current Answers
Answer #1: Posted by Autodiy on February 11th, 2015 9:22 AM
Autodiy
Member since:
May 23rd, 2014 Points: 815,136
Member since:
May 23rd, 2014 Points: 815,136
try the link below
http://www.ereplacementparts.com/hitachi-c10fce2-compound-miter-saw-parts-c-7927_13297_13298.html
Www.autodiy.co.za
Related Hitachi C10FCE2 Manual Pages
Operating Instructions - Page 4
... CHECK FOR DAMAGED PARTS BEFORE USING THE TOOL. Do not
leave tool until it comes to provide support for damage before using the tool.
18. This tool was not designed to this
POWER TOOL before inserting the power plug into the tool against the rotation direction of the slide
compound saw.
25. Apply 120 volts AC only to...
Operating Instructions - Page 5
... POWER TOOL unattended without them would be thrust
form the table and cause bodily harm.
10. When replacing the saw blade with the tool shall direct the user to secure the tool to supporting...14. Never use of the
compound saw is in the moving parts, including the blade, while the saw .
22.
use on the supporting surface. Never operate the tool while wearing loose clothing, a ...
Operating Instructions - Page 6
... place your finger is on the starting switch does not turn off properly. 13. Never attempt to warning sign " " while the tool is 10" (255mm). 9. Always wear eye protection when using the compound saw blade. 6. Saw blade diameter is being operated.
Never operate the saw without the guards in place. 17. REPLACEMENT PARTS
When servicing use the POWER...
Operating Instructions - Page 7
..., follow the normal electrical safety precautions given in this power tool, and only genuine HITACHI replacement parts should disassemble or assemble this Instruction Manual, including not using an...regularly. If in doubt, use this power tool, HITACHI has adopted a double insulation design. Ampere Rating
More
Not More
Than
Than
0 - 6
6 - 10
10 - 12
12 - 16
MINIMUM GAGE FOR...
Operating Instructions - Page 9
English
SPECIFICATIONS
Item
Model
C 10FCH / C 10FCE
Motor
Type
Series commutator motor
Power source
Single-phase AC 60Hz
Voltage (Volts)
120
Full-load current (Amp)
15
Laser Marker Maximum output
Operating Instructions - Page 10
... careful not to the rear of bolts (6mm). Injuries could result.
10 Installation
Base
5/16" (8mm) Bolt
10-3/8" (267mm) 1" (25mm) Thick Bench
11/32" (9mm) 4 Holes
16-11/16" (424mm)
Work Bench 5/16" (8mm) Nut
Fig. 4
Attach the power tool to a level, horizontal work bench. For example, use 2-11/32" (60mm) or larger bolts for...
Operating Instructions - Page 12
... Repair or replace the power cord if an inspection indicates that it is faulty.
8. For precise cutting, rotate the saw blade. Oblique angle
Before the power tool is shipped from...confirm that no operating abnormalities exist before attempting a cutting operation.
10. Confirm the tool's power cord is standing behind, the power tool start and confirm that the power cord plug fits properly in ...
Operating Instructions - Page 13
...tool, causing in Fig. 10.
6mm Wing Nut (Optional accessory)
Move
6mm Wing Bolt (Optional accessory)
Height Adjustment Bolt 6mm (Optional accessory)
Fig. 10... turned off. * Exercise utmost caution in handling a switch trigger for precision cutting ... (Stopper and holder are optional...bolt as the power plug is pulled inadvertently, the saw blade can realize stable cutting of left side of
...
Operating Instructions - Page 17
... or personal injury always firmly tighten the miter handle.
5. Starting from the workpiece.
use of the tool without pulling back, causes the safety cover to rest on the left side of alignment, or with the right hand side for compound cutting, because the saw blade.
6.
Compound cutting procedures
Compound cutting can be caught in 4 and 5 above...
Operating Instructions - Page 20
...work is done in a vise assembly.
NOTE: If the spindle lock cannot be blown out of the workpiece and tighten it to prevent the duct and the safety cover from the receptacle before removing or installing a saw... blade rotates. Set the wood plate near the cutting section of the dust bag when the saw blade. Duct Right Angle
Base
(2) During bevel and compound...it using tools other than...
Operating Instructions - Page 21
... and the rotation direction of this tool.
1. CAUTION: Never attempt to install saw blade can cause ineffective operation and possible overload to operate the power tool.
21
The saw blades larger than 10" (255mm) in paragraph 1 above. Always install saw blade. CAUTION: Never use a dull saw blades that the trigger switch is turned
OFF and the power plug...
Operating Instructions - Page 22
...a secure place. Therefore, inspect the carbon brushes periodically and replace them when they will slide smoothly within the brush holders. ...tool. Inspecting the lever
If the M6 hexagonal head bolts (2) are loose, align the sides of the fence and saw ... tool if any loose part.
The carbon brushes can result in good condition and that the following has been performed:
(1) Trigger switch ...
Operating Instructions - Page 23
... hinge * Rotary portion of machine oil is recommended. To assure that only authorized replacement parts will be protected, all service (other waste material from the surface of HITACHI.
23 Lubrication
Lubricate the following sliding surfaces once a month to keep the power tool in good operating condition for a long time (see Fig. 1 and Fig...
Parts List - Page 1
E946
ELECTRIC TOOL PARTS LIST
COMPOUND SAW Model C 10FCE2
2006 • 10 • 11 (E1)
4 5 6 7
13 14
46 47 48 49 50
3
9 8
12 11
10
22 23 24 25 26
21
15 16
39 40 41 42 43 44 45
18 19 20
38
27 28 29
53 54
55
...
46 47 48 65
629 615 619 626 627
619 620
613 609
612 611 610
621
622
623 67
626
624
627 66
625 Hitachi Power Tools
LIST NO.
Parts List - Page 3
...-342 FLAT HD. CODE NO.
3 307-956
DESCRIPTION
NO. SCREW M6X25 (10 PCS.)
1
53 326-704 SUB FENCE (B)
1
54 326-698 FENCE (B)
1
10 -- 06
* ALTERNATIVE PARTS
C 10FCE2 --- 3 ---
SOCKET SET SCREW M6X10 1
REMARKS
4 323-208 MACHINE SCREW (W/WASHERS) M6X20 (BLACK) 1
5 322-935 CLAMP LEVER
1
6 326-706 BOLT (LEFT HAND) M10
1
7 318-934 SPECIAL WASHER
1
8 322-889...
Parts List - Page 4
...102 319-107 TCT SAW BLADE 255MM-D30 HOLE-NT30 1
* 102 319-106 TCT SAW BLADE 255MM-D25.4 HOLE-NT24 1
* 102 318-963 TCT SAW BLADE 255MM-D15.88 HOLE-NT24 1
* 102 318-964 TCT SAW BLADE 255MM-D25.4 ...10 PCS.) 1
116 961-729 CUSHION
1
117 949-340 FLAT HD. SCREW M6X16 (10 PCS.)
1
118 949-217 MACHINE SCREW M4X12 (10 PCS.)
1
119 949-429 BOLT WASHER M4 (10 PCS.)
1
120 322-920 HOOK
1
121 326...
Parts List - Page 5
...-141 CONNECTOR 50092 (10 PCS.)
2 FOR USA, CAN
* 159 958-308Z PILLAR TERMINAL (A)
1 EXCEPT FOR USA, CAN
* 160 326-709 NOISE SUPPRESSOR
1 FOR AUS, AUT, EUROPE, INA, GBR (230V), TUR
* 160 326-710 NOISE SUPPRESSOR
1 FOR GBR (110V)
162 984-750 TAPPING SCREW (W/FLANGE) D4X16
2
163 937-631 CORD CLIP
1
* 166 326-700 SWITCH (3P FASTON...
Parts List - Page 6
... (1 PAIR)
2 FOR 110V-120V
* 182 999-065 CARBON BRUSH (1 PAIR)
2 FOR 220V-240V
183 945-161 BRUSH CAP
2
* 184 322-949 LINK
1
C 10FCE2
--- 6 ---
* ALTERNATIVE PARTS
10 -- 06 USED
REMARKS
1 INCLUD. 177
* 176 340-687E STATOR ASS'Y (B) 220V-230V
1 INCLUD. 177
* 176 340-686E STATOR ASS'Y 220V
1 INCLUD. 177 FOR CHN
* 176...
Parts List - Page 7
...
629 322-710 GUIDE ASS'Y
1 INCLUD. 615, 619, 626, 627
* 630 976-472 TCT SAW BLADE CROSS-CUT 255MM-D15.9 HOLE 1 FOR USA, CAN
* 631 319-658 TCT SAW BLADE 255MM-D15.88 HOLE-NT100 1 FOR USA, CAN
C 10FCE2
10 -- 06
* ALTERNATIVE PARTS
--- 7 --- CODE NO. DESCRIPTION
501 940-543 BOX WRENCH 10MM
502...
Parts List - Page 8
USED
REMARKS
C 10FCE2
--- 8 --- DESCRIPTION
NO. Printed in Japan 10 -- 06 (061011N) ITEM NO.
CODE NO.
Similar Questions
C10fs Compound Miter Saw Bearing Replacement
how do I remove the bearing from the armature
how do I remove the bearing from the armature
(Posted by Bobster8820 3 years ago)
Hand Arm Vibration Syndrome Expoture Limit - 9 Inch Grinder
Can you provide Hand arm vibration syndrome expoture limit - 9 inch grinder?
Can you provide Hand arm vibration syndrome expoture limit - 9 inch grinder?
(Posted by RejeshKannan 9 years ago)
How To Adjust Cut Depth Hitachi 10 Compound Miter Saw Manual
(Posted by dbrag 10 years ago)
Clamp Lever
I just got a hitachi c10fce2 compound miter saw. I have not been able to move the saw from its packe...
I just got a hitachi c10fce2 compound miter saw. I have not been able to move the saw from its packe...
(Posted by bigvern 11 years ago)
Where Can I Get A Free Manual On The Hitachi C12rsh 12' Slide Compound Miter Saw
(Posted by kathy86883 14 years ago)