Hitachi EC119SA Support Question
Hitachi EC119SA Support Question
Find answers below for this question about Hitachi EC119SA - 15 Amp 2.5 HP Lon Twin-Stack Air Compressor.Need a Hitachi EC119SA manual? We have 1 online manual for this item!
Question posted by w39dennis on March 13th, 2018
Air Outlet
I put a new regulator on the compressor. I do not get any air out of air connections. advise what may be the cause. thanks
Current Answers
Answer #1: Posted by BusterDoogen on March 13th, 2018 11:07 AM
BusterDoogen
Member since:
October 30th, 2011 Points: 28,565,397
Member since:
October 30th, 2011 Points: 28,565,397
If your compressor keeps running and only builds to 25 psi, I would suspect the reed valves, head gaskets or a leak. With the compressor running spray soapy water on all fittings, around the head area and tank components. If no leak is found, remove the air filter and feel for suction at the intake(make sure head is not too hot). If you feel good suction at first then suction is lost after reaching 25 psi, most likely reeds or gaskets (with bad reed valves, sometimes you will actually feel air blowing out of the intake).
I hope this is helpful to you!
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Related Hitachi EC119SA Manual Pages
Instruction Manual - Page 3
... situation before operating or maintaining this Instruction Manual. Most accidents that the planned use will be avoided by WARNINGS on the compressor and in minor or moderate injury, or may cause machine damage.
indicates a potentially hazardous situations which , if ignored, could result in the Instruction Manual before it occurs, and by observing...
Instruction Manual - Page 4
... When compressor is damaged should be used outdoors, use of unnecessary tools, debris, furniture, etc.
16. Compressor should...cord from the air tank before connecting the compressor to avoid damaging this compressor without all work ...15. Never use compressed air for use compressor if switch does not turn it will operate properly and perform its operation. Operate the compressor...
Instruction Manual - Page 5
... their nameplates. Check for air tools and accessories. Risk of the pressure switch OFF, disconnect it from the power source and open valve slowly and tilt compressor to be operating unusually, making strange noises or vibration, or otherwise appears defective, stop using . Water will corrode and weaken the air tank causing a risk of bursting. DO...
Instruction Manual - Page 6
...compressor should be determined to make a repair yourself, remember that looks like extending from electric shock. Never connect the green (or green and yellow) wire to a permanent ground, such as a properly grounded outlet... will cause a...that accept the compressor's plug. ... (0 - 7.6)
26 - 50
51 - 100
(7.9 - 15.2) (15.5 - 30.5)
101 - 150 (30.8 - 45.7)
AWG...connected to a live " terminal...
Instruction Manual - Page 7
... bumper
Quick coupler (air outlet)
Knob of the pressure reducer
SPECIFICATIONS
Model Motor Power Source Output Power Current Tank Capacity Maximum Pressure
Free Air Delivery
Lubrication
Fig.1
at 40 PSI (2.8 bar) at 90 PSI (6.2 bar) at 100 PSI (6.9 bar)
EC119SA Single-Phase, Induction Motor Single-Phase, 120V AC 60Hz
1.6 HP (1.2KW) 15.0 A
4 gal. (15.1 ltr) 135 PSI...
Instruction Manual - Page 8
... shown below 32°F (0°C) or above 104°F (40°C).
- 8 - If such a faulty receptacle is used, may cause overheating, resulting in dipstick is free from the power source, use compressor for repair service.
WARNING: Make sure air vent in a serious hazard.
10°max
10°max
Fig.5
7. English
ACCESSORY
5.
ON
OFF...
Instruction Manual - Page 9
... face and eyes away from power source. Adjustment of the plug. Compressor outlet pressure must be tripped, the compressor will corrode and weaken the air tank causing a risk of bursting. A pressure gauge (B) is too high. WARNING: Disconnect the compressor from the power source and remove the compressed air from the level that shown on the pressure switch.
Instruction Manual - Page 10
... use only (2) Check the oil level of use . Use a phillips All quality compressors will cause premature compressor failure. English
1. Draining tank
Drain tank daily or after 4 hours of the pumping... and repairs must be performed by a HITACHI
WARNING: Never clean filter element with compressed air (Fig. 9).
NOTE: Specifications are subject to Fig. 7). 3. Unfasten the oil drain...
Similar Questions
Just Bought A New Regulator Installed It And Air Is Leaking Out Of The Pin Holeo
the pin hole on the round part that butts to cover plate that holds it on
the pin hole on the round part that butts to cover plate that holds it on
(Posted by Johnjaboor 2 years ago)
Hitachi C10ra3 Compatible Blades.
Can I use an 8 inch blade with this saw? If so, can it be for cutting ceramic tile?
Can I use an 8 inch blade with this saw? If so, can it be for cutting ceramic tile?
(Posted by gwoltman 3 years ago)
Can't Get Air Out Of Quick Couplers.
Replaced the broken pressure reducer still no air and the working pressure Gage doesn't work. could ...
Replaced the broken pressure reducer still no air and the working pressure Gage doesn't work. could ...
(Posted by lstoner34 3 years ago)
Wiring Diagram For Hitachi Miter Saw
I bought a switch for Hitachi c10 fc2 & need a wiring diagram to hook it upThank You Dave
I bought a switch for Hitachi c10 fc2 & need a wiring diagram to hook it upThank You Dave
(Posted by delliott49 7 years ago)
Air Escaping From Exhaust Cover At The Top Of Gun
what should i replace? is the gun shot?
what should i replace? is the gun shot?
(Posted by ronyungwirth 11 years ago)