Hitachi NV45AE - Coil Roofing Nailer Support and Manuals
Get Help and Manuals for this Hitachi item
View All Support Options Below
Free Hitachi NV45AE manuals!
Problems with Hitachi NV45AE?
Ask a Question
Free Hitachi NV45AE manuals!
Problems with Hitachi NV45AE?
Ask a Question
Most Recent Hitachi NV45AE Questions
Air Escaping From Exhaust Cover At The Top Of Gun
what should i replace? is the gun shot?
what should i replace? is the gun shot?
(Posted by ronyungwirth 11 years ago)
Popular Hitachi NV45AE Manual Pages
Instruction Manual - Page 3
... avoided, may result in DEATH or SERIOUS INJURY. Hazards that result from the operation and maintenance of Nailers are outlined in the "SAFETY" section of the operating instructions, safety precautions and warnings in this manual before it occurs, and by the failure to prevent bodily injury or machine damage are identified by DANGERS...
Instruction Manual - Page 5
... long hair.
13. NEVER USE IN PRESENCE OF FLAMMABLE LIQUIDS OR GASES. The Nailer produces sparks during operation. KEEP VISITORS AWAY. A serious injury can be stored in moving parts. In order ... that all screws and covers tightly mounted. Check their condition periodically. DO NOT LOAD FASTENERS WITH TRIGGER OR PUSH LEVER DEPRESSED. DO NOT DRIVE FASTENERS INTO THIN BOARDS...
Instruction Manual - Page 6
...Hitachi authorized service center.
26. STAY ALERT. To avoid this Manual. and do not drop the Nailer or strike the Nailer against hard surfaces; MAINTAIN NAILER WITH CARE. DO NOT DISCONNECT AIR HOSE FROM NAILER WITH FINGER ON TRIGGER. Do not operate the Nailer....
29. USE ONLY PARTS, ACCESSORIES OR FASTENERS SUPPLIED OR RECOMMENDED BY HITACHI. The Nailer should never be operating ...
Instruction Manual - Page 7
...OTHERS!
- 7 - If driving fasteners with the nail guide open , the fasteners can be ignited by operators and others in personal injury.
3. IMPORTANT SAFETY INSTRUCTIONS FOR USING NV45AE(S) COIL NAILER
WARNING
1. NEVER USE GASOLINE OR OTHER HIGHLY FLAMMABLE LIQUIDS FOR CLEANING. Ensure that Nailers are used before repair. Ensure that this MANUAL is available to operators and personnel...
Instruction Manual - Page 8
...
NOTE: The information contained in the safe operation of the Nailer.
NAME OF PARTS
Piston O-ring Piston
Driver blade
Exhaust cover
Trigger
Body
Cap Air plug (sold separately)
Magazine cover
Adjuster
A
Magazine assembly
A
Nose
Push lever
Feeder Nail holder
Section A-A Main nail stopper Nail guide
Shingle guide
Firing head (outlet)
Feeder
Feed piston
Magazine assembly
Magazine...
Instruction Manual - Page 9
... and resulting injuries. The use only the genuine HITACHI nails for M4 screw
23
1 1 1
- 9 - STANDARD ACCESSORIES
1
1 Eye protection 2 Allen wrench for M5 screw 3 Allen wrench for the NV45AE/NV45AE(S).
Only nails shown in tool malfunction and/or nail breakdown, leading to serious injuries. English
SPECIFICATIONS
Model Operating pressure Dimensions
Length × Height × Width...
Instruction Manual - Page 10
.... (120 cc) oil feeder
(Code No. 874042)
1 quart (1 ltr) can be on the part of HITACHI. BEFORE OPERATION
Read section titled "SAFETY" (pages 4 - 7). Drain daily.
2. The regulator controls the operating pressure for the Nailer and extend the Nailer life. Inspect the lubricator before operation to pressure which potentially exceeds 200 psi (13.7 bar 14 kgf/cm2...
Instruction Manual - Page 11
...; air consumption at given air pressure × safety factor (always 1.2) Example: 2 Nailers operating at high pressure. Before actually beginning the nailing work, test the Nailer by using the Nailer and contact a Hitachi authorized service center immediately.
(1) DISCONNECT AIR HOSE FROM NAILER. If any screws are loose, tighten them.
Ⅺ THE PUSH LEVER AND TRIGGER MUST MOVE SMOOTHLY...
Instruction Manual - Page 12
... than required air pressure unnecessarily over stresses the Nailer. and 3) keep Nailer pointed downward.
(1) Grip the nail guide and knob with the length of the nail holder according to 70 psi (4.9 bar 5 kgf/cm2). Connect the air hose. Do not load any nails in the actual application.
Ⅺ THE NAILER MUST OPERATE PROPERLY.
Depress the push lever against...
Instruction Manual - Page 13
... the magazine cover is forcibly closed without adjusting the nail holder correctly, the nail holder may be damaged.
- 13 -
Mark
Otherwise, the nail guide will not feed smoothly if the nail holder is forcibly closed without adjusting the nail holder correctly, the nail holder may be damaged.
(3) Place the nail coil in the magazine. If the magazine cover is not...
Instruction Manual - Page 14
... hole
Guide slot
First nail
23
Nail guide
2 Pawl
Feeder
NOTE: Be careful not to deform the collated wires and not to ANSI Z87.1 specifications. Nails can be driven into and through or away from workpiece and hit someone . ⅷ In order to avoid double fire or unwanted ejection of a nail due to bouncing of the Nailer. 1) do...
Instruction Manual - Page 15
... SEQUENTIAL TRIP MECHANISM may bounce from the Nailer; 2) remove all warnings and instructions. ⅷ Always handle nails and package carefully. Continuous operation (Push lever fire):
(1) Intermittent operation (Trigger fire) 1 Position the nail outlet on the workpiece with a bouncing motion. The nailer with the following "Method of loaded nails can be dropped or driven
at an...
Instruction Manual - Page 17
...contact a Hitachi
authorized service center. Main nail stopper
Nail guide
Nail
Slotted screw driver 5 Cut the deformed collated wire with a hammer. and 2) clearing a jam.
ⅷ Never use gasoline or other highly flammable liquides for cleaning.
1. Hammer
Rod
Outlet 1
Disconnect air hose
4 Remove the jammed nail with a slotted screw driver.
2.
Some illustrations in this Manual is designed...
Instruction Manual - Page 18
... the nose and push lever. Maintenance chart (See page 19)
8. Service parts list
A: Item No. code numbers and/or design) may soften the tar on the shingles and cause tar buildup to avoid rust.
⅜ Do not store the Nailer in a cold weather environment. NOTE: Specifications are constantly being improved and modified to change without prior...
Instruction Manual - Page 19
.... Driver blade worn? Use Hitachi pneumatic tool lubricant.
Keep the Nailer operated properly. HOW Open manual petcock. Follow manufacturer's instructions.
Intermittent feed. CHECK METHOD Open nail guide. Piston O-ring cut or heavily worn? CORRECTION Clear a jam per page 12 or 13. Use only recommended nails.
Fill with dirt. If problems persist, contact a Hitachi authorized service...
Hitachi NV45AE Reviews
We have not received any reviews for Hitachi yet.