Hitachi NT65A3 - Power Tools 2-1/2'' Finish Nailer Support and Manuals
Get Help and Manuals for this Hitachi item
View All Support Options Below
Free Hitachi NT65A3 manuals!
Problems with Hitachi NT65A3?
Ask a Question
Free Hitachi NT65A3 manuals!
Problems with Hitachi NT65A3?
Ask a Question
Popular Hitachi NT65A3 Manual Pages
Instruction Manual - Page 3
... if not avoided, may result in this Manual. EXPLANATION OF THE NAILING ACTION OF THE HITACHI NAILER
⅜ SINGLE ACTUATION MECHANISM (SINGLE SEQUENTIAL ...nails.
3 Basic safety precautions are outlined in the "SAFETY" section of the operating instructions, safety precautions and warnings in this manual before it occurs, and by observing appropriate safety procedures. Never use this Nailer...
Instruction Manual - Page 5
... in use the Nailer if parts are driven away from the Nailer when the coupling joint is not set properly, the nailer will not operate correctly.
20.BE CAREFUL OF DOUBLE FIRE DUE TO RECOIL. NEVER USE NON RELIEVING COUPLER ON NAILER. Do not drive fasteners on the Nailer, the Nailer can ricochet and hurt someone.
19. This Hitachi nailer includes a nailing operation...
Instruction Manual - Page 6
... Nailer. The Nailer can lead to be operated by a Hitachi authorized service ...HITACHI. NEVER USE NAILER FOR APPLICATIONS OTHER THAN THOSE SPECIFIED IN THIS MANUAL. 32. NEVER MODIFY OR ALTER A NAILER. English
SAFETY - Operate the Nailer according to an air supply. 28. Unauthorized parts, accessories, or fasteners may be hidden by Hitachi, distributor or employer shall repair the Nailer...
Instruction Manual - Page 7
... PROTECTOR by operators and others in safe working order. 5. Ensure that Nailers which require repair are wearing
EYE PROTECTOR. 3.
Keep Nailers in work area. 4. Ensure that this MANUAL is available to operators and personnel performing maintenance. 2. English
EMPLOYER'S RESPONSIBILITIES
1. Ensure that Nailers are used only when operators and others in work area are not further...
Instruction Manual - Page 9
... × 76 mm)
4.4 lbs. (2.0 kg)
150 Nails
.031 ft3/cycle at 100 psi (.88 ltr/cycle at 6.9 bar) (.88 ltr/cycle at 7 kgf/cm2)
3/8 NPT Thread
NAIL SELECTION
WARNING
● Be sure to serious injuries. Only nails shown in the Table below can result in tool malfunction and/or nail breakdown, leading to use of nails
16 Gauge Finish Min.
Instruction Manual - Page 11
... an oil mist to be used to supply compressed air to pressure which potentially exceeds 200 psi (13.7 bar 14 kgf/cm2).
● Never use oxygen or other bottled
gases. Nailer Side
Regulator Compressor Side
Lubricator
Filter
11 WARNING
● Never connect Nailer to this Nailer must comply with an automatic drain. Use Hitachi pneumatic tool lubricant.
Instruction Manual - Page 12
...; Use Hitachi pneumatic tool lubricant. Dust Cap
Install a 3/8 NPT male plug at the air inlet. Air consumption
Using the Air consumption table and the Air compressor size formula, find a compressor providing 3.3 CFM of Hitachi pneumatic tool lubricant into the air plug on the Nailer.
3/8 NPT Male Plug
5. Without proper lubrication, the Nailer will not work properly and parts...
Instruction Manual - Page 13
... part. Conduct the tests in a cold weather environment.
Slow speed operation tends to ANSI Z87.1 specifications.
Before actually beginning the nailing work area MUST wear safety glasses with side shields which conforms to warm up before use Nailer unless push lever is already cold, bring it in work , test the Nailer by using the Nailer and contact a Hitachi authorized service...
Instruction Manual - Page 16
... back and hang it over stresses the Nailer.
Adjust the air pressure at a higher than required air pressure unnecessarily over the roll pin.
Nail Feeder
Roll pin (2) 1 Insert nail strips one by one from above the magazine.
2 Slide nails forward in the magazine.
1
2 Nail strips Magazine
16 Using the Nailer at recommended operating pressure 70 - 120 psi (4.9 - 8.3 bar...
Instruction Manual - Page 18
...
This Hitachi nailer includes a nailing operation switching device. nails can be...use Nailer as an option. Part no. 884178. Explanation of an angle; After nailing once, nailing will be possible again until the trigger is important. First, pull the trigger; If the trigger is held back, a nail will not be driven each time the push lever is properly set properly, the nailer...
Instruction Manual - Page 19
... operation (Push lever fire): (1) Intermittent operation (Trigger fire) Use the SINGLE ACTUATION MECHANISM setting.
WARNING
● Unlike the FULL SEQUENTIAL ACTUATION MECHANISM, please note that the SINGLE ACTUATION MECHANISM of operation to drive nails with this Hitachi nailer will be set to CONTACT ACTUATION MECHANISM.)
2 Position the nail outlet on the workpiece with the push lever and...
Instruction Manual - Page 22
... coat of frequent jam, contact a
Guide Plate (A)
Hitachi authorized service center.
2. WARNING
● Disconnect air hose and remove all nails.
3 Release the lock lever and open
guide plate.
4 Remove the jammed nail with a
slotted-head screwdriver.
3
5 Close guide plate and latch.
1 Disconnect air hose
6 In case of the lubricant to the steel parts to assist you in the safe...
Instruction Manual - Page 23
...presented with the tool to incorporate the latest technological advancements. Used D: Remarks
Warning Label
CAUTION: ● Repair, modification and inspection of power tools, the safety regulations and standards prescribed in each country must be observed. B: Code No. Service parts list A: Item No. In the operation and maintenance of Hitachi Power Tools must be carried out by an...
Instruction Manual - Page 24
...Lubricate the Nailer after Extend the Nailer life. Drain air compressor. English
SERVICE AND REPAIRS
WARNING
● Only service personnel trained by Hitachi, distributor or employer shall repair the Nailer.
● Use only parts supplied or recommended by Hitachi for repair.
Maintenance chart
ACTION
WHY
HOW
Drain air line filter daily.
NOTE: Specifications are subject...
Instruction Manual - Page 25
...or damaged?
Replace nail feeder. Replace ribbon spring.
English
Operator troubleshooting Most minor problems can be resolved quickly and easily using the table below. If problems persist, contact a Hitachi authorized service center for a jam.
Nail feeder damaged? Ribbon spring weakend or damaged? Check air pressure.
Nails jam. Driven nail is driven. Driver blade worn...
Hitachi NT65A3 Reviews
We have not received any reviews for Hitachi yet.