Harman Kardon AVR 320 Support Question
Harman Kardon AVR 320 Support Question
Find answers below for this question about Harman Kardon AVR 320.Need a Harman Kardon AVR 320 manual? We have 2 online manuals for this item!
Question posted by artronic22 on January 19th, 2016
Avr320 Osd Congiguration
Harman Kardon avr320 keep loosing digital input configuration when main power go off, do this amp is using memory battery or eprom to keep configuration and where is locate ? I m retired electronic tech but do not have the service manual, this is my own receiver, thanks for your helpArturo Carrillo
Current Answers
Answer #1: Posted by TommyKervz on January 19th, 2016 12:14 PM
TommyKervz
Member since:
January 10th, 2013 Points: 17,776,833
Member since:
January 10th, 2013 Points: 17,776,833
Harman Kardon AVR does not have a battery inside but there is a small capacitor on the circuit board just behind the display. This capacitor is to keep settings if the unit is unplugged for some few hours. If you never unplug it then this capacitor might be dead and need to be replaced.
Related Harman Kardon AVR 320 Manual Pages
Owners Manual - Page 2
AVR 320 Audio/Video Receiver
3 Introduction
4 Safety Information
4
Unpacking
5 Front Panel Controls
8 Front Panel Information Display
10 Rear Panel Connections
12 Main Remote Control Functions
15 Zone II Remote Control Functions
16 Installation and Connections
18 System Configuration
18
Speaker Placement
19
System Setup
20
Input Setup
20
Surround Setup
22
Speaker Setup
23
...
Owners Manual - Page 3
...eight-channel input make the AVR 320 capable of listening enjoyment. The AVR 320's powerful amplifier uses traditional Harman Kardon high-current design technologies to meet the wide dynamic range of any questions about to accommodate tomorrow's new formats right on board. The lightning flash with everything needed to begin many years of handling all the latest digital audio sources. The...
Owners Manual - Page 6
When the button is being made using the Channel Select Ù or Digital Select Û buttons, this button may also be configured as an output jack, to feed a digital signal to a CD-R, MiniDisc or other products that have been entered into the AVR 320's memory.
# Preset Station Selector: Press this button to scroll up one of available modes...
Owners Manual - Page 10
... jacks here. If an external AM antenna is in use , connect the Surround Back Left and Surround Back Right channel outputs of a compact disc player or CD changer.
• Multiroom Outputs: Connect these jacks to an optional audio power amplifier to listen to the matching digital input connector on a DVD or other video source.
¶...
Owners Manual - Page 11
...video source device with the System Power Control Button 2.
° Unswitched AC Accessory Outlet: This outlet may be used .
e Remote IR Input: If the AVR 320's frontpanel IR sensor is the ...inputs of a DVD player to the red (+) terminal on Harman Kardon (or other video source. Connect the output of the sensor to this outlet regardless of all devices connected to the accessory...
Owners Manual - Page 16
... SACD player is used to connect speaker pairs be influenced by the distance between your area.
Connections to a subwoofer are a different distance from a cable TV system. Connect the analog audio and video outputs of the amplifier feeding those channels.
Connect the output of the AVR 320 to the matching digital input connections on the AVR 320.
3. Assemble the...
Owners Manual - Page 17
... main room installation, the Remote IR Output Jack d on the rear panel should not be viewed in the "ON" position. System and Power Connections
The AVR 320 is designed for more information on input configuration.)
Video Connection Notes: • When the component video jacks are used , connect the Component Video Output b to the appropriate Optical or Coaxial Digital Inputs...
Owners Manual - Page 18
...be placed almost anywhere in 5.1-channel operation, the preferred location for a subwoofer is to move things around the ... the main surround speakers on the side walls of the room sound smooth, and that audio transitions across...used , the same model or brand of the room. A few configuration adjustments that they are as far away from ceiling
At least 2 feet
When the AVR 320 is used...
Owners Manual - Page 19
... the speaker configuration, digital input, surround mode, delay times, crossover frequency and output levels for example, that
19 SYSTEM CONFIGURATION When the menu is in the Main Information Display Y and the OSD Indicator P will automatically be adjusted.
When the full OSD menu system is used . When the semi-OSD system is used, OSD ON will appear in use the AVR 320's onscreen...
Owners Manual - Page 20
...;/› Buttons o 37 until the desired digital or analog input is shown in the Main Information Display Y and in configuring the AVR 320 is easiest to configure each input. To return to enter the menu and the IN/OUT SETUP menu (Figure 2) will appear on -screen cursor will drop down to use as possible, we suggest that surround-encoded...
Owners Manual - Page 24
...digital receiver such as the AVR 320, as correct outputs ensure that you hear sound tracks with standard speakers or the "7" Numeric Key r on -screen display or Main Information Display Y.
3. Using EzSet Harman Kardon's...CENTER DELAY is in the Speaker/Channel Input Indicators Q where the letters for three seconds.
Once the correct channel configuration button has been pressed the test ...
Owners Manual - Page 25
... in the Main Information Display Y.
Enjoy!
25 SYSTEM CONFIGURATION Manual Output Level Adjustment Output levels may also be different from a speaker location does NOT match the position indicated in music and hometheater listening. After checking for operation. NOTE: The subwoofer output level is most cases, only the digital input and surround mode will use. The output...
Owners Manual - Page 28
... Out appear momentarily in the front-panel Input Indicators ˆ.
• When an audio source is selected, the last video input used remains routed to turn the unit "off by the amber color of the Power Indicator 3.
• To program the AVR 320 for the first time, you must press the Main Power Switch 1 on the
front panel to...
Owners Manual - Page 29
... be connected to their appropriate inputs on the AVR 320 rear panel (e.g., connect the analog stereo audio output from the front panel, press the Surround Mode Selector 9 to scroll up DEGIJKLMN. This does not indicate a problem with the DTS signal as indicated by pressing the Digital Select Button qÛ and then using either press the front...
Owners Manual - Page 30
... range of available surround modes is present, the AVR 320 uses a variety of surround modes are inside the Speaker/Channel Input Indicators Q will light in 5.1 audio. Depending on the settings on the source player and specific surround information and number of channels on the type of digital data that tell you have to make some cases...
Owners Manual - Page 31
...If your Harman Kardon dealer for compact discs and laser discs.
Operation
flash. This is properly tuned and should be selected from a 30-position memory. The AVR 320 will only...digital audio system used with the AVR 320.
• Note that the desired frequency band is available, the MP3 Bitstream Indicator A will light, and the audio will automatically be connected directly to locate...
Owners Manual - Page 32
... 320's memory for this will return to its normal default setting as an input. Press the Set Button p@ when the name of copyrighted materials is circulating, the Program/SPL Indicator c will appear in the Main Information Display Y. To use the Selector Buttons 7$ or the ⁄/ ¤ Buttons n to the rear panel digital outputs, the AVR 320 offers Harman Kardon's exclusive configurable...
Owners Manual - Page 33
... on the AVR. Note that when the 6-Channel or 8-Channel Direct Input is highlighted. At each channel position use . Then, use . When all the levels to their original factory default of high-resolution optical audio playback systems such as DVD-Audio or SACD. Operation
Repeat the procedure as needed until the desired input configuration appears in the Main Information...
Owners Manual - Page 36
... configured for the average do not make , press the OSD Button v to the AVR 320's location with optional remote external infrared (IR) sensors, speakers and power amplifiers. Press the Set Button p to the AVR 320's rear panel Multiroom IR Input f, you are in the main listening room where the AVR 320 is in the Main Information Display ˜, and the Main Information Display Y or OSD...
Owners Manual - Page 50
Setup Code Table: Tape
Manufacturer/Brand Setup Code Number
HARMAN KARDON
001
Setup Code Table: Audio
Manufacturer/Brand Setup Code Number
HARMAN KARDON
001
Setup Code Table: DVD
Manufacturer/Brand APEX DIGITAL CALIFORNIA AUDIO DENON GE GOLDSTAR HARMAN KARDON JVC KENWOOD LG LOTTE MAGNAVOX MARANTZ MITSUBISHI NAD ONKYO OPTIMUS PANASONIC PHILIPS PIONEER PROCEED PROSCAN RCA RUNCO SAMSUNG ...
Similar Questions
I Am Getting Unlock When I Switch On Dts Or Dolby Gegital Input
to do unlock digital sources in avr 7300
to do unlock digital sources in avr 7300
(Posted by richardjoshuah 3 years ago)
No Sound In Sub Hkts 15 Conected On Avr 151
I have a kit 5.1 HKTS 15 connected to an AVR 151 the problem is that I can not sound the subwoofer.s...
I have a kit 5.1 HKTS 15 connected to an AVR 151 the problem is that I can not sound the subwoofer.s...
(Posted by OsTRC 8 years ago)
Correct Hookup For Avr And Cable Box. Dvi Input To Television
Does HDMI in pass through to HDMi out for watching Television without surround sound speakers.
Does HDMI in pass through to HDMi out for watching Television without surround sound speakers.
(Posted by kevin13149 9 years ago)
Harman Kardon Avr 320 Manual
How do I change the source to digital on the avr 320?
How do I change the source to digital on the avr 320?
(Posted by ebooth 10 years ago)
Power Transformer For Harman Kardon Avr320
Hell, I need to replace the power trnsformer in this unit as it makes audible noise ( the wirings )...
Hell, I need to replace the power trnsformer in this unit as it makes audible noise ( the wirings )...
(Posted by toutelectronique 11 years ago)