Genie TriloG 1200 Support Question
Genie TriloG 1200 Support Question
Find answers below for this question about Genie TriloG 1200.Need a Genie TriloG 1200 manual? We have 1 online manual for this item!
Question posted by dalehandyman on September 12th, 2014
Programing Remote
How do you program a remote for my Genie Trilog 1200?
Current Answers
Related Genie TriloG 1200 Manual Pages
Owner's Manual - Page 1
... Technology Company. Homelink ® and Car2U® compatible. GARAGE DOOR OPENER MODELS PowerMax® 1200/1500, SC 1200/1500, TriloGTM 1200/1500, PowerLift® 900, GPowerTM 900,
SilentMax® 1000/1200, CB 1000/1200, IntelliG® 1000/1200
SCREW/BELT/CHAIN DRIVES
OPERATION & MAINTENANCE MANUAL
Includes INTELLICO®DE 2 Remote Control. Safe-T-Beam® System must be installed to...
Owner's Manual - Page 2
... date of Powerhead Controls 5 Travel Limits Closing Garage Door (DOWN Limits 6 Opening Garage Door (UP Limits 7 Wall Console Overview 8 Series III Wall Consoles with Black Buttons... 8 Series II Wall Consoles with White Buttons.... 8 Force and Speed Control 9 Contact Reverse Test 9 Remotes/New Intellicode 2 Openers 10
O5ptional 6Program7ming
Keypad 12 Clearing Memory for...
Owner's Manual - Page 3
...Genie® Company or your local Genie® Factory Authorized Dealer.
• DO NOT install operator on ,
or next to do so.
• Locate the wall console button: A) Within sight of door. B) At a minimum height of opening while door...balanced door.
1 Safety Information
OVERVIEW OF POTENTIAL HAZARDS
READ THIS SAFETY INFORMATION
CONVENTIONS USED IN THESE INSTRUCTIONS Garage doors are...
Owner's Manual - Page 4
..., the garage door will stop and reverse a closing of the opener. G999-393 Manual-ScrewBeltChain-EN indd 4
7/13/12 10 17 AM Contact your Genie® Professional Dealer for an Assembly/Installation Instructions poster, if needed , or call 1-800-35GENIE. The door stops and reverses to a desired rate, vary limits and force, and program new remotes. LED...
Owner's Manual - Page 5
... require programming. There are 4 programs (The 2 "Factory Set" programs are only 2 "required" programming processes you will need changes.) 1. Door Speed Program (Factory Set) - Use the following information will want to program the opener so that your Genie garage door opener is preset at the factory.
INTRODUCTION
Now that the door opens and closes properly and all remote devices...
Owner's Manual - Page 6
... arrow button (-) until the long LED comes on blue (round LED remains off). See page 17. PROGRAM
SET
+
NOTE: If shuttle/bullet has NOT been engaged to complete each step. Closing Garage Door (Down Limits)
1 Lift the door open by hand until the shuttle/bullet
engages the carriage on the rail.
4 Press and hold the...
Owner's Manual - Page 7
... flash blue and go off). HOLD
Opening Garage Door (Up Limits)
NOTE: Beginning with powerhead.
PROGRAM
SET
- PROGRAM
PROGRAM
- +
ET
G999-393 Manual-ScrewBeltChain-EN indd 7
The UP (open , then release. PROGRAM
SET
-
3 Required Programming
5 Press and release the Program Set button (both
LEDs flash blue and go off). PROGRAM
PROGRAM
SET
- Watch carriage as it approaches...
Owner's Manual - Page 8
....
To powerhead
Sure-Lock™ Button
-
Independent Light Control Button Controls door opener lights from inside garage.
8
Series III Wall Consoles with this button to open or close door.
LOCK disables controls
after
door is ON, the powerhead cannot be activated by the wall console or a remote. • Press and hold for 5 seconds (or until this light...
Owner's Manual - Page 9
... the Contact Reverse Test.
NOTE: Force or Speed controls DO NOT require programming. Contact Reverse Test
NOTE: The Limit and Force settings MUST BE COMPLETED before performing the Contact Reverse Test.
11 Open the garage door using the Open/Close
buttonon the Wall Console.
NOTE: Using these settings is closing tight to set DOWN limits...
Owner's Manual - Page 11
...the same button on your Intellicode remote when it's searching
SET
- BASIC PROGRAMMING IS COMPLETE AND YOUR GARAGE DOOR IS READY TO USE!
PROGRAM
IMPORTANT: Your HomeLink® device
will ONLY respond to pressing THIS button
on the remote
(the door should open or close).
PROGRAM
SET
-
to connect to Genie mode.
The Remote button is now programmed. Repeat as described in...
Owner's Manual - Page 12
... full instructions packed with the keypad. When the door has stopped moving, pressing on steady.
The door will stay on any key will begin ashing purple
Opener
2. Opener LEDs will automatically stop or start programming steps over. Your keypad is in motion. Press Up/Down key again. Door opener will run. To erase, follow the steps in...
Owner's Manual - Page 13
... will not activate the door opener. NOTE: The garage door opener will not activate the door opener. NOTE: Clearing Remotes from a missing Remote.
All remaining (or recovered) Remotes and wireless Keypads MUST BE reprogrammed as shown on the Powerhead
and hold until both LEDs flash blue and then go OFF.
PROGRAM
PROGRAM
4 To verify that was previously programmed to the Powerhead.
G999...
Owner's Manual - Page 14
...
on the transmitter is programmed to your door opener has a black antenna wire and the serial number does not start with Intellicode® 2 openers. All new Remotes have questions, see your older Genie® door opener. If you have the button directly above the logo on your Genie® instructions for this Intellicode® 1 model of Genie® garage door openers .The default...
Owner's Manual - Page 16
...and away from door to prevent contacting it while operating the console. If the system appears to be at : 1-800-35-GENIE or visit ...door manually about 3' to 4' feet and let go. Door should stop and
reverse to the fully open . Failure to adjust the opener properly may cause severe injury or death. 6.
6 Maintenance and Adjustments
If you have your garage door Owner's Manual. Keep remote...
Owner's Manual - Page 17
... or step stool. • When replacing light cover, make sure wires are programmed. Reset Open/Close Travel Limit Performing all eleven (11) Limits/Force setting steps (see pages...GPower™ 900 require light bulbs of remote. 2. Door will not close the door automatically unless the Safe-T-Beam® System is engaged to door opener. • Open powerhead light cover. • Remove light...
Owner's Manual - Page 19
...; 900, GPower™ 900 openers DO NOT have the option to increase speed. Please note that speed may not have the option to increase speed. NOTE: Depending on adjacent doors facing in both LEDs
turn BLUE.
PROGRAM
Both LEDs FLASH SET BLUE to maintain alignment with condition of the garage receives direct sunlight. •...
Owner's Manual - Page 21
....
• Check closing "FORCE" adjustment. See page 8. • WARNING: If you suspect a problem with the garage door hardware or springs, contact
The Genie Company at STBs.
Erase all remotes. • Replace remote battery with door arm connected to close , the opener can cut wires. Turn Sure-Lock™ OFF and check operation. • Check for normal operation...
Owner's Manual - Page 22
...• Be sure all door fasteners are tight. • Be sure garage door is in good repair, properly lubricated and balanced. • Be sure opener is less than 6-feet, opener configures programming for a one-piece door. • Contact The Genie Company at 1-800-35GENIE concerning door speed.
No response from unit.
Thermal cutout
Program remote using instructions on a one...
Owner's Manual - Page 23
...1200, CB 1000/1200, IntelliG® 1000/1200
LIMITED WARRANTY
GMI Holdings, Inc d/b/a The Genie Company ("Seller") warrants to the original purchaser of the below identified, SilentMax® 1000/1200, CB 1000/1200, IntelliG® 1000/1200, PowerMax® 1200/1500, SC 1200/1500, TriloG™ 1200/1500, PowerLift® 900, or GPower™ 900 garage door openers...
OPENER MODEL: _____
REMOTE ...
Owner's Manual - Page 24
...design
• Beeps and flashes green when garage door closes. Also available at your garage door close properly
• Network Adapter required
Easy operation at Home Improvement outlets and other remotes or wall buttons
Check out NEW ACCESSORIES and PRODUCTS;
Closed Confirm™ Wireless Remote
(Works with all Genie garage door openers
manufactured from 1993 to the present •...
Similar Questions
Trilo G 1200
I replaced board. my operator will only work if I hold up or down arrow on head.
I replaced board. my operator will only work if I hold up or down arrow on head.
(Posted by wcpelton 2 years ago)
Door Opener Will Not Operate After Power Company Had Power To House Shut To Hous
Power company notified me that power to my house was cut-off for about 15 minutes today. Came home a...
Power company notified me that power to my house was cut-off for about 15 minutes today. Came home a...
(Posted by fsmith4iva 6 years ago)
Garage Door Opener Not Working
Green light and red light are on the safety"eye" When pushing wall, remote or key pad the screw driv...
Green light and red light are on the safety"eye" When pushing wall, remote or key pad the screw driv...
(Posted by scanty5 9 years ago)
Genie Garage Door Opener Powermax 1200 Will Not Work
(Posted by EpiNiaddisk 9 years ago)
I Have A Genie Powermax 1200 And It Is Too Long To Fit In The Space I Have.
My door is a 6' door and the old opener is 114" this one is 127". Can I cut the rail and screw drive...
My door is a 6' door and the old opener is 114" this one is 127". Can I cut the rail and screw drive...
(Posted by gringo915 9 years ago)