Genie PowerMax 1500 Support Question
Genie PowerMax 1500 Support Question
Find answers below for this question about Genie PowerMax 1500.Need a Genie PowerMax 1500 manual? We have 1 online manual for this item!
Question posted by LauraAnnKnapp on August 30th, 2014
Powermax 1500, Revolution Series
It was working great. Then last week, the motion-sensitve light went out. I replaced the bulbs. No luck. Then I knocked one of the bulbs out of the inlet; it shows bare wires now. So I turned off the power source The garage door continues to work well. Help?
Current Answers
Related Genie PowerMax 1500 Manual Pages
Owner's Manual - Page 1
...; System must be installed to the store. For use only with a one piece overhead garage doors. Call us: 800-354-3643
For Answers and Assistance: 1.800.354.3643
or visit ...injury to persons or damage to property - Need help or have questions? GARAGE DOOR OPENER MODELS PowerMax® 1200/1500, SC 1200/1500, TriloGTM 1200/1500, PowerLift® 900, GPowerTM 900,
SilentMax® 1000/1200, CB ...
Owner's Manual - Page 2
... with all United States and Canadian legal
requirements as of the date of Powerhead Controls 5 Travel Limits Closing Garage Door (DOWN Limits 6 Opening Garage Door (UP Limits 7 Wall Console Overview 8 Series III Wall Consoles with Black Buttons... 8 Series II Wall Consoles with White Buttons.... 8 Force and Speed Control 9 Contact Reverse Test 9 Remotes/New Intellicode...
Owner's Manual - Page 3
...Could result
in Death or Serious
Injury
Turn OFF power before installing operator.
• Where possible,...the source of power until instructed to the door before removing opener cover. When replacing cover, make sure wires are NOT ...door opener. 1 Safety Information
OVERVIEW OF POTENTIAL HAZARDS
READ THIS SAFETY INFORMATION
CONVENTIONS USED IN THESE INSTRUCTIONS Garage doors are large, ...
Owner's Manual - Page 4
... Monitors the Safe-T-Beam® system to ensure proper functionality and will reverse automatically to fully open /close . 3.When the garage door is activated and automatically turns OFF 4 minutes later. Automatic Lighting System Two bulb lighting system supplies light for an installation poster, if needed , or call 1-800-35GENIE. Automatic ForceGuard™ Control Automatically sets...
Owner's Manual - Page 5
... (Default menu) - These show you how to program your garage door opener for use. Door Force Program (Factory Set) - This program is preset at the factory. The following steps guide you through setting your Genie garage door opener is used for you. "TRAVEL LIMITS" 2. Powerhead: There are 3 programming buttons and 2 LED lights on bottom of the opener.
Door Travel Limits Program...
Owner's Manual - Page 6
...opener can restart as many times as necessary to property.
• DO NOT operate this unit from wall console before LIMITS are set.
If not illuminated, check for
2 seconds until
garage door is fully closed on the rail.
4 Press and hold the down arrow button (-) for correct wiring... step.
NOTE: Before setting limits confirm wall console red indicator light (or backlight) is ON.
Owner's Manual - Page 7
... carriage as it approaches the power head to avoid contact with garage door closed ) limit is programmed.
8 Press and hold the up arrow button (+) until the long LED light comes on blue (round LED remains off).
PROGRAM
PROGRAM
- +
ET
G999-393 Manual-ScrewBeltChain-EN indd 7
The UP (open) limit is fully open, then release.
PROGRAM
SET...
Owner's Manual - Page 8
... controls to turn Sure-Lock™ OFF. Note: If opener has a Motion Detector sensor, it will keep powerhead lights ON as long as motion is detected. Indicator Light -Red indicator backlight is ON. -When Sure-Lock™ is ON, the indicator light is OFF. Independent Light Control Button Controls door opener lights from inside garage.
Indicator Light -Red indicator light is always...
Owner's Manual - Page 9
... Test.
Repeat this manual (pages 18-19).
10 Open and close to the oor. The door MUST complete a full cycle from open and close your garage door using the Wall
Console Open/Close button.
13 Close the garage door using the Open/Close button
on the powerhead will clear the lights. Force and Speed Limits are factory programmed and automatically...
Owner's Manual - Page 11
... for other garage door openers, repeat the steps above using one of the other two Remote buttons. Follow the Car2U or HomeLink instruction to pressing THIS button
on your remote in "Learn Mode" as necessary for additional Remotes.
To program the same Remote for three door openers. BASIC PROGRAMMING IS COMPLETE AND YOUR GARAGE DOOR IS READY...
Owner's Manual - Page 12
... unauthorized hands, you have successfully erased the old programming.
2. The long LED will turn o . 5. Enter your PIN. 3.
NOTE: Pressing any single button will automatically stop or start programming steps over.
When blinking stops you must start the opener while the door is ready for 5 seconds or until backlight goes off (30 seconds)
NOTE...
Owner's Manual - Page 13
... that the memory is pressed the round LED will flash blue but will not activate the door opener.
PROGRAM
- +
3 Press up arrow button (+) and down arrow
button (-) simultaneously on..., round LED comes ON. NOTE: The garage door opener will no longer recognize any signal received from the Powerhead memory will not activate the door opener. All remaining (or recovered) Remotes and ...
Owner's Manual - Page 14
... (the LED on the Opener
5 Press the Remote button 2 times (the LED on the transmitter is programmed to your door opener has a black antenna wire and the serial number does... 3 times.
***Repeat Step 2 to turn ON).
The LED color displayed on the Remote back to GREEN for this Intellicode® 1 model of Genie® garage door openers .The default Intellicode® 2 setting must...
Owner's Manual - Page 16
...door controls. 2.
Verify wire routing from STBs to STB connection in sight and away from drive system.
• Raise and lower the door manually-it while operating the console.
6 Maintenance and Adjustments
If you have your garage door...- The door MUST reverse on the floor. Control must be working properly. Use caution when using this release with the door open position. ...
Owner's Manual - Page 17
...light bulbs of remote. 2. CORRECTIVE MAINTENANCE
Changing Light Bulbs
WARNING
• Use extreme caution when working from a ladder or step stool. • When replacing light cover, make sure wires are programmed. Reset Open/Close Travel Limit Performing all eleven (11) Limits/Force setting steps (see pages 6-8) erases previous Limits/Force settings.
To engage shuttle to door opener...
Owner's Manual - Page 19
... BLUE
OFF Flashes BLUE 3 Times
Then the Current Speed setting for the opener can be positioned further away from door opening if necessary to avoid sunlight but no further off the wall to increase speed. Sun
Red
Green
LED
LED
One Door Garage
19
G999-393 Manual-ScrewBeltChain-EN indd 19
7/13/12 10 17...
Owner's Manual - Page 21
... good one. Erase all remotes. • Replace remote battery with the garage door hardware or springs, contact
The Genie Company at 1-800-35GENIE. If not, check fuse or circuit breaker.
• If power is OK. - Door starts up .
If lamp works, power source is OK, -
See pages 6-7. • Be sure door, opener, and springs are properly set with button...
Owner's Manual - Page 22
...Door component failure detected. Thermal cutout
Program remote using instructions on a one -piece door. • Contact The Genie Company at 1-800-35GENIE concerning door speed.
Door may need professional repair/adjustment. • Is this opener installed on page 14. Check power...operation.
WHAT TO DO
• Be sure all door fasteners are tight. • Be sure garage door is in .
Owner's Manual - Page 23
.../1200, PowerMax® 1200/1500, SC 1200/1500, TriloG™ 1200/1500, PowerLift® 900, or GPower™ 900 garage door openers, ("Product...wired wall control, Safe-T-Beam® system, J-Arm and rail
Seller's obligation under this warranty is specifically limited to repairing or replacing, at its option, a replacement Product (shipping and handling of any replacement part(s) or replacement...
Owner's Manual - Page 24
... Tan Almond
Color-Match These Covers to Your Home - 4 Color Options by Special Order
Perfect Stop Parking System • Garage parking guide for Leading-Edge Technology or the Perfect Update/Replacement? can open door without remote • Lighted keypad with Revolution Series 1500, 1200 and 1000 Models)
• Sleek and compact design
• Beeps and flashes green when...
Similar Questions
What Amp Fuse Is In The Powermax 1500
what amp fuse is in the genie powermax 1500 model 4062
what amp fuse is in the genie powermax 1500 model 4062
(Posted by chrisdhoak 5 years ago)
Genie Silent Max 1000 Revolution Series Red Light Blinking And Garage Door Not W
(Posted by Anonymous-151741 8 years ago)
Genie Silentmax 1000 Revolution Series Manual
I have the genie silent max 1000 revolution series. It's installed amd working fine but 2 minor prob...
I have the genie silent max 1000 revolution series. It's installed amd working fine but 2 minor prob...
(Posted by kaf76716 9 years ago)
Where Is The Reset Button On Genie Garage Door Opener Powermax 1500
(Posted by jpIJac 9 years ago)
Powermax 1500 Revolution Series Model 4062
Door opener will open with both remotes and via the wireless keypad outside mounted. It will NOT clo...
Door opener will open with both remotes and via the wireless keypad outside mounted. It will NOT clo...
(Posted by brianmaclennan 9 years ago)