Genie SilentMax 1000 Support Question
Genie SilentMax 1000 Support Question
Find answers below for this question about Genie SilentMax 1000.Need a Genie SilentMax 1000 manual? We have 1 online manual for this item!
Question posted by Anonymous-151741 on June 4th, 2015
Genie Silent Max 1000 Revolution Series Red Light Blinking And Garage Door Not W
The person who posted this question about this Genie product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by TechSupport101 on June 26th, 2015 10:00 AM
TechSupport101
Member since:
May 24th, 2013 Points: 12,171,305
Member since:
May 24th, 2013 Points: 12,171,305
That is a program error - uplug the unit for 5 minute and then plug it back and observe. Otherwise, Safe-T-Beam is a government-required safety feature that must be installed in order for your Genie garage door opener to work. A flashing Safe-T-Beam LED indicator means a malfunction has occurred. First, be sure that the lenses are clean, and check for any possible obstructions or loose wires. Also, make sure that lenses are mounted five to six inches from the floor on either side of the garage-door opening and that lenses are aligned facing one another. If the LED indicator continues to flash, see your owner's manual for a list of possible causes and additional troubleshooting.
Related Genie SilentMax 1000 Manual Pages
Owner's Manual - Page 1
...-T-Beam® System must be installed to close door. Use this opener only with residential sectional or one -piece or sectional door. GARAGE DOOR OPENER MODELS PowerMax® 1200/1500, SC 1200/1500, TriloGTM 1200/1500, PowerLift® 900, GPowerTM 900,
SilentMax® 1000/1200, CB 1000/1200, IntelliG® 1000/1200
SCREW/BELT/CHAIN DRIVES
OPERATION & MAINTENANCE MANUAL
Includes...
Owner's Manual - Page 2
... with all United States and Canadian legal
requirements as of the date of Powerhead Controls 5 Travel Limits Closing Garage Door (DOWN Limits 6 Opening Garage Door (UP Limits 7 Wall Console Overview 8 Series III Wall Consoles with Black Buttons... 8 Series II Wall Consoles with White Buttons.... 8 Force and Speed Control 9 Contact Reverse Test 9 Remotes/New Intellicode...
Owner's Manual - Page 3
... information in this manual to call a of the doorway. tion, call your local Genie® Factory Authorized Dealer.
• DO NOT install operator on ,
or next ...At a minimum height of opening while door is the safety alert symbol. 1 Safety Information
OVERVIEW OF POTENTIAL HAZARDS
READ THIS SAFETY INFORMATION
CONVENTIONS USED IN THESE INSTRUCTIONS Garage doors are large, heavy objects ...
Owner's Manual - Page 4
... is installed improperly, press and hold the wall console "open /close . 3.When the garage door is interrupted by continuously changing the access code each new code only once.
Review the Assembly and Installation poster to download a printable file.
Automatic Lighting System Two bulb lighting system supplies light for an installation poster, if needed , or call 1-800...
Owner's Manual - Page 5
... PROGRAMMING"
Term Definitions:
Travel Limits programming allows you through setting your Genie garage door opener is needed to move door during programming and advance through programming your particular door and is used to how fast or slow your opener opens and closes your opener's functional settings for minor adjustments under certain circumstances.
4. Overview of Powerhead...
Owner's Manual - Page 6
...unit from wall console before LIMITS are set. You can occur.
• T he shuttle MUST be activated. Closing Garage Door (Down Limits)
1 Lift the door open by hand until the shuttle/bullet
engages the carriage on the rail.
4 Press and hold the down arrow button ...and clear of the step and start over. NOTE: Before setting limits confirm wall console red indicator light (or backlight) is ON.
Owner's Manual - Page 7
... 2 seconds
7 Release up arrow button (+) until the long LED light comes on blue (round LED remains off).
PROGRAM
PROGRAM
- +
ET
G999-393 Manual-ScrewBeltChain-EN indd 7
The UP (open , then release. Watch carriage as it approaches the power head to avoid contact with garage door closed ) limit is programmed.
8 Press and hold the up...
Owner's Manual - Page 8
...is completely closed .
Independent Light Control Button Controls door opener lights from inside garage.
Independent Light Control Button Controls door opener lights from inside garage. Indicator Light -Red indicator backlight is ON. -When Sure-Lock™ is ON, the indicator light is pressed again or a door action has been completed.
Open/Close Button Use this...
Owner's Manual - Page 9
... when you use the Wall Console to open after contact with the reversal of the
door opening.
Repeat this manual (pages 18-19).
10 Open and close your garage door using the Wall
Console Open/Close button.
13 Close the garage door using the Open/Close button
on the powerhead will clear the lights. Contact Reverse Test
NOTE: The Limit and...
Owner's Manual - Page 10
...Set button (the long LED
begins flashing purple).
This Remote is preset for use with this opener. NOTE: Each button on the Powerhead, you have 30 seconds to execute each step. If...PROGRAM
17 Press and release the button you see two flashing red LEDs on each step.
3 Required Programming
REMOTES / New Intellicode 2 Openers
NOTE: The following these steps.
14 Press and hold Remote...
Owner's Manual - Page 11
... Remote can be programmed for other garage door openers, repeat the steps above using one of the other two Remote buttons.
G999-393 Manual-ScrewBeltChain-EN indd 11
11
7/13/12 10 17 AM To program the same Remote for three door openers. Follow the Car2U or HomeLink instruction to Genie mode.
3 Required Programming
18 Press...
Owner's Manual - Page 12
... off (30 seconds)
NOTE: Rapid blinking of the red LED on steady. The long LED will automatically stop or start programming steps over. Press in "Setting Up a Pina"nd"Programming. Press Up/Down key again. NOTE: Pressing any single button will activate door until the LED starts to Opener
PROGRAM
- + HOLD 2 seconds
PROGRAM
SET...
Owner's Manual - Page 14
...® 1) models of opener. Once the LED on the Remote turns RED when the button is pressed...color displayed on your Genie® instructions for this Intellicode® 1 model of Genie® garage door openers .The default Intellicode...Opener
5 Press the Remote button 2 times (the LED on the transmitter is programmed to be opened . The light lens may need to your door opener...
Owner's Manual - Page 16
... garage door automatically or manually if door is working properly, perform the check as follows:
• With the door closed, pull manual emergency release handle DOWN and let go . Check wiring and wire connections. NEVER let children operate or play with the door open position. After adjusting either the force or limit of lighting feature. Have a trained door...
Owner's Manual - Page 17
...Performing all eleven (11) Limits/Force setting steps (see pages 6-8) erases previous Limits/Force settings.
To engage shuttle to door opener. • Open powerhead light cover. • Remove light bulb(s). • Replace light bulb(s).
- DO NOT use light bulbs with a CR 2032 coin cell battery. 1.
Compact CFL's may also be used.
-
Replace battery. 3. Pull/release cord down...
Owner's Manual - Page 19
.... Flashes BLUE 3 Times
OFF
Then the Current Speed setting
for OPENING travel will cross. • Place the Source (Red LED) Safe-T-Beams on adjacent doors facing in both LEDs
turn BLUE. NOTE: Depending on the direct sunlight side
Multiple Garage Doors • NEVER position Safe-T-Beam modules where signals will display. Sensor modules CAN be...
Owner's Manual - Page 21
... poster or download poster from adjacent Safe-T-Beam® units. • Contact The Genie Company at 1-800-35GENIE. See page 17. • Reposition door opener antenna.
• Remote LED does not come ON with the garage door hardware or springs, contact
The Genie Company at 1-800-35GENIE. Refer to make sure chain/belt is engaged into...
Owner's Manual - Page 22
... sure garage door is in good repair, properly lubricated and balanced. • Be sure opener is less than 6-feet, opener configures programming for a one -piece door is lowest speed setting. • If carriage travel . Door may need professional repair/adjustment. • Is this opener installed on page 14. Normal speed for one -piece door. • Contact The Genie Company...
Owner's Manual - Page 23
...; 900, SilentMax® 1000/1200, CB 1000/1200, IntelliG® 1000/1200
LIMITED WARRANTY
GMI Holdings, Inc d/b/a The Genie Company ("Seller") warrants to the original purchaser of the below identified, SilentMax® 1000/1200, CB 1000/1200, IntelliG® 1000/1200, PowerMax® 1200/1500, SC 1200/1500, TriloG™ 1200/1500, PowerLift® 900, or GPower™ 900 garage door openers...
Owner's Manual - Page 24
..., Security All in addition to other retail/commercial locations nationwide. enables safe parking in garage
Universal Wall Push Button • Easy to door - visit www.GenieCompany.com or call 1-800-35-GENIE.
can open door without remote • Lighted keypad with Revolution Series 1500, 1200 and 1000 Models)
• Sleek and compact design
• Beeps and flashes green when...
Similar Questions
Genie Silent Max 1000 Blinks Purple Does Not Operate
(Posted by pjsgramir 9 years ago)
My Remote Will Not Open Genie Silent Max 1000 And Red Light Lights Up On Remote
(Posted by jovaler 10 years ago)
Genie Silent Max 1000 Wall Console Opens The Door But Will Not Close It
(Posted by ankjason 10 years ago)