Genie PowerMax 1200 Support Question
Genie PowerMax 1200 Support Question
Find answers below for this question about Genie PowerMax 1200.Need a Genie PowerMax 1200 manual? We have 1 online manual for this item!
Question posted by burleyprice on August 5th, 2015
Does The 1200 Series Have A Fuse For The Motor
The person who posted this question about this Genie product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by TechSupport101 on August 5th, 2015 6:16 PM
TechSupport101
Member since:
May 24th, 2013 Points: 12,171,305
Member since:
May 24th, 2013 Points: 12,171,305
Related Genie PowerMax 1200 Manual Pages
Owner's Manual - Page 1
... or have questions?
GARAGE DOOR OPENER MODELS PowerMax® 1200/1500, SC 1200/1500, TriloGTM 1200/1500, PowerLift® 900, GPowerTM 900,
SilentMax® 1000/1200, CB 1000/1200, IntelliG® 1000/1200
SCREW/BELT/CHAIN DRIVES
OPERATION & MAINTENANCE MANUAL
Includes INTELLICO®DE 2 Remote Control.
Genie, Genie logo, Intellicode, Safe-T-Beam, IntelliG, PowerMax, PowerLift, ChainMax and...
Owner's Manual - Page 2
... Important Safety Instructions 3 Infrared Protection Function 3
F3eatures
Safety 4 Opener 4
R4equired5Progra6mming
Introduction 5 Overview of Powerhead Controls 5 Travel Limits Closing Garage Door (DOWN Limits 6 Opening Garage Door (UP Limits 7 Wall Console Overview 8 Series III Wall Consoles with Black Buttons... 8 Series II Wall Consoles with White Buttons.... 8 Force and...
Owner's Manual - Page 3
... and disable all
moving objects, springs under high tension and electric motors.
Repairs and adjustments
to the door before removing opener cover. This is moving parts. 1 Safety Information
OVERVIEW OF POTENTIAL HAZARDS
READ THIS SAFETY INFORMATION
CONVENTIONS USED IN THESE INSTRUCTIONS Garage doors are large, heavy objects that has a broken spring. When replacing cover...
Owner's Manual - Page 4
Review the Assembly and Installation poster to ensure all steps have been completed.
The door stops and reverses to its fully opened position. Safe-T-Reverse® Contact Reversing System Automatically stops and reverses a closing of the door opener by
a person or obstacle, the garage door will stop and reverse a closing , if Safe-T-Beam® is interrupted by...
Owner's Manual - Page 5
... the powerhead of the buttons is preset at the factory. Use the following information to program functions. Powerhead: There are no objects in the garage door opening and closing your garage door.
Remote Programming synchronizes your remote control devices (remotes, wall console, and keypad) with the powerhead.
Force Control refers to how much power is...
Owner's Manual - Page 6
...LED remains off). If you have 30 seconds to complete each step. Severe damage to the opener can restart as many times as necessary to execute each step.
(continued next page)
G999...must go back to carriage BEFORE setting limits.
See page 17. Closing Garage Door (Down Limits)
1 Lift the door open by hand until
garage door is fully closed on the Powerhead, you see two solid red or ...
Owner's Manual - Page 7
... it approaches the power head to avoid contact with garage door closed ) limit is programmed.
8 Press and hold the up arrow button (+) and the round LED
will begin flashing.
PROGRAM
SET
- SET
HOLD 2 seconds
7 Release up arrow button (+) for
2 seconds until door
is fully open ) limit is recommended but not necessary.
6 Press and hold...
Owner's Manual - Page 8
... ) to activate Sure-Lock™. • Press and release to open or close garage door.
Use only the wall console provided with 10 or higher.
Independent Light Control Button Use this button to turn powerhead lights ON.
Open/Close Button Opens and closes door from inside garage.
8
Series III Wall Consoles with White Buttons
Indicator Light Large white...
Owner's Manual - Page 9
... contacting the board or if it does not reverse direction to open after contact with the reversal of the
door opening. Repeat this manual (pages 18-19).
10 Open and close your garage door using the Wall
Console Open/Close button.
13 Close the garage door using the Open/Close button
on the powerhead will clear the lights. FORCE AND...
Owner's Manual - Page 11
Each Remote can be programmed for other garage door openers, repeat the steps above using one of the other two Remote buttons. BASIC PROGRAMMING IS COMPLETE AND YOUR GARAGE DOOR IS READY TO USE! Follow the Car2U or HomeLink instruction to set the button in the car to your Intellicode remote when it's searching
SET
-
...
Owner's Manual - Page 12
... key again. Your keypad is in order 3-5-7. 2. When the blinking stops, you must start the opener while the door is ready for 2 seconds. (The round LED turns blue and then goes o . Press the ...your PIN or you fear it may have successfully erased the old programming.
2. Door opener will automatically stop or start programming steps over. Press Up/Down key . Enter your current PIN, then...
Owner's Manual - Page 13
...G999-393 Manual-ScrewBeltChain-EN indd 13
(continued next page) 13
7/13/12 10 17 AM NOTE: The garage door opener will not activate the door opener. Your opener will clear ALL programmed Remotes and wireless Keypads. All remaining (or recovered) Remotes and wireless Keypads MUST BE reprogrammed...
SET
SET
HOLD HOLD
If the memory has been cleared, the Remote will not activate the door opener.
Owner's Manual - Page 14
...and GREEN LEDs on the Remote turn the RED LED on the transmitter is programmed to your door opener has a black antenna wire and the serial number does not start with 10 or higher,...above the logo on the Remote back to GREEN for this Intellicode® 1 model of Genie® garage door openers .The default Intellicode® 2 setting must be changed to Intellicode® 1. (Follow these same ...
Owner's Manual - Page 16
... GO UNDER A STOPPED, PARTIALLY OPEN DOOR. 5. After adjusting either the force or limit of severe injury or death. KEEP DOORS PROPERLY BALANCED. See your door springs serviced.
• Close the door. (continued next page)
G999-393 Manual-ScrewBeltChain-EN indd 16
7/13/12 10 17 AM SAVE THESE INSTRUCTIONS
WARNING
• Garage door hardware (springs, cables, brackets...
Owner's Manual - Page 17
...and Engaging Carriage/Bullet
Screw Drive
Opener
Belt/Chain Drive
Opener
Disengaged
Engaged
Disengaged Engaged
To engage bullet to door opener. • Open powerhead light cover. • .... 1. Close powerhead light cover. 2. Replace battery. 3.
To engage shuttle to door opener.
• Test light operation. Remote Battery Replacement Replace remote battery with greater than...
Owner's Manual - Page 19
...Door Garage
Single Garage Door • Determine which side of door components and tracks. Speed settings should not need adjustment with Safe-T-Beam Sensor (Green LED). Note: PowerLift® 900, GPower™ 900 openers... motors only) Speed settings are pre-programmed at the factory for sectional doors.
NOTE: Depending on heavier sectional doors. Sensor modules CAN be affected by door ...
Owner's Manual - Page 21
...remote lost or stolen? See page 17. • Reposition door opener antenna.
• Remote LED does not come ON with the garage door hardware or springs, contact
The Genie Company at 1-800-35GENIE. .... • Program remote to the store. If not, check fuse or circuit breaker.
• If power is OK. -
Door opener starts for binding.
• Check closing "FORCE" adjustment. See...
Owner's Manual - Page 22
WHAT TO DO
• Be sure all door fasteners are tight. • Be sure garage door is in good repair, properly lubricated and balanced. • Be sure opener is in UP or DOWN travel is lowest speed setting. • If carriage travel .
Check power supply.
Door contact in good repair. Remove obstruction, recheck unit. Remove obstruction...
Owner's Manual - Page 23
...for a period of the Product
PowerLift®, 900 , GPower™ 900 MOTOR - Seller warrants the motor for the LIFETIME* of FIVE (5) YEARS ACCESSORIES - Seller warrants all other ...SilentMax® 1000/1200, CB 1000/1200, IntelliG® 1000/1200, PowerMax® 1200/1500, SC 1200/1500, TriloG™ 1200/1500, PowerLift® 900, or GPower™ 900 garage door openers, ("Product"), subject...
Owner's Manual - Page 24
... Wall Push Button • Easy to mount inside garage
• Used in One
Keyless Entry Pad • Wireless;
can open door without remote • Lighted keypad with Revolution Series 1500, 1200 and 1000 Models)
• Sleek and compact design
• Beeps and flashes green when garage door closes. G999-393 Manual-ScrewBeltChain-EN indd 24
™ 7/13...
Similar Questions
The Garage Door Stopped Working,one Sensor Is Green The Other Is Blinking Red,
i tried re aligning the sensor with no luck. Any suggestions?Thanks Mar
i tried re aligning the sensor with no luck. Any suggestions?Thanks Mar
(Posted by Bigassneal 7 years ago)
Garage Door Opener Not Working
Green light and red light are on the safety"eye" When pushing wall, remote or key pad the screw driv...
Green light and red light are on the safety"eye" When pushing wall, remote or key pad the screw driv...
(Posted by scanty5 9 years ago)
Genie Garage Door Opener Powermax 1200 Will Not Work
(Posted by EpiNiaddisk 9 years ago)
Where Is The Reset Button On Genie Garage Door Opener Powermax 1500
(Posted by jpIJac 9 years ago)
Garage Door Does Not Function At All.
Unit has power. Unit responds to both remotes and keypad with 4 clicks (one set and then another) bu...
Unit has power. Unit responds to both remotes and keypad with 4 clicks (one set and then another) bu...
(Posted by tysonlemka 10 years ago)