Home » Genie » Garage Door Openers » Genie PowerMax 1200

Genie PowerMax 1200 Support Question

Find answers below for this question about Genie PowerMax 1200.
Need a Genie PowerMax 1200 manual? We have 1 online manual for this item!

Genie Overview Questions Manuals Reviews Videos Research

Question posted by parsons2507 on April 9th, 2013

Where Is The Learn Button On A Powermax 1200

The person who posted this question about this Genie product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by LuxuriKnows on April 10th, 2013 12:21 AM

This answer was accepted by the poster of the original question.

LuxuriKnows

Member since:
March 25th, 2013

Points: 495,290

1,100
points

Hello There, the learn button can be found on the remote that comes with the garage opener. See Manual page 11 for diagram : here

★ Hit "Accepted" or "Helpful" ✔ : If I Helped to Resolve Question.

✘ Didn't help? Resubmit Your Question : Include More Details if Possible |✘

Related Genie PowerMax 1200 Manual Pages

Owner's Manual - Page 1

... dba The Genie Company Homelink is a registered trademark of Johnson Controls Technology Company. GARAGE DOOR OPENER MODELS PowerMax® 1200/1500, SC 1200/1500, TriloGTM 1200/1500, PowerLift® 900, GPowerTM 900, SilentMax® 1000/1200, CB 1000/1200, IntelliG® 1000/1200 SCREW/BELT/CHAIN DRIVES OPERATION & MAINTENANCE MANUAL Includes INTELLICO®DE 2 Remote Control.

Owner's Manual - Page 2

... Important Safety Instructions 3 Infrared Protection Function 3 F3eatures Safety 4 Opener 4 R4equired5Progra6mming Introduction 5 Overview of Powerhead Controls 5 Travel Limits Closing Garage Door (DOWN Limits 6 Opening Garage Door (UP Limits 7 Wall Console Overview 8 Series III Wall Consoles with Black Buttons... 8 Series II Wall Consoles with all United States and Canadian...

Owner's Manual - Page 3

...to call your safety and the safety of the door. • Install the entrapment WARNING label next to the wall button or console, in Death or Serious Injury DO NOT...presented, call a of opening while door is used throughout this manual. 1 Safety Information OVERVIEW OF POTENTIAL HAZARDS READ THIS SAFETY INFORMATION CONVENTIONS USED IN THESE INSTRUCTIONS Garage doors are large, heavy ...

Owner's Manual - Page 4

...passes through the garage. The door opener responds to its fully opened position. If the Safe-T-Beam® System fails, loses power, or is activated and automatically turns OFF 4 minutes later. Lights automatically turn OFF after completing assembly and installation of contact with : Open/Close, Sure-Lock™, and independent light control buttons. INFRARED PROTECTION...

Owner's Manual - Page 5

... has been successfully completed. Door Speed Program (Factory Set) - These buttons should NOT be used for programming ONLY. move (open/ close) your particular door and does NOT require programming. Speed Control refers to how fast or slow your opener opens and closes your door travels up and down in the garage door opening and closing your garage door. Remote Programming synchronizes...

Owner's Manual - Page 6

...) or call Customer Service at 1-800-35GENIE or visit www.geniecompany.com 3 Release down arrow button (-) until the long LED comes on blue (round LED remains off). See page 17. Closing Garage Door (Down Limits) 1 Lift the door open by hand until the shuttle/bullet engages the carriage on the rail. 4 Press and hold the...

Owner's Manual - Page 7

... - + SET The DOWN (closed is recommended but not necessary. 6 Press and hold the up arrow button (+) for 2 seconds until door is programmed. PROGRAM SET - 3 Required Programming 5 Press and release the Program Set button (both LEDs flash blue and go off ). HOLD Opening Garage Door (Up Limits) NOTE: Beginning with powerhead. SET HOLD 2 seconds 7 Release up arrow...

Owner's Manual - Page 8

... when wall console is properly wired and Sure-Lock™ is OFF. Independent Light Control Button Controls door opener lights from inside garage. Note: Constant button pressure in the CLOSE mode will override STB fault in the powerhead and close garage door. When Sure-Lock™ is ON, indicator light flashes. When Sure-Lock™ is ON...

Owner's Manual - Page 9

... and reverse direction within 2 seconds to improperly set . 12 Lay a 2" x 4" board at under the center of the door opening. Repeat this manual (pages 18-19). 10 Open and close your garage door using the Wall Console Open/Close button. 13 Close the garage door using the Open/Close button on the powerhead will clear the lights. For further help, refer to...

Owner's Manual - Page 11

... GARAGE DOOR IS READY TO USE! Follow the Car2U or HomeLink instruction to Genie mode. G999-393 Manual-ScrewBeltChain-EN indd 11 11 7/13/12 10 17 AM 3 Required Programming 18 Press and release the same button on the remote (the door should open or close). to connect to pressing THIS button on your remote in "Learn...

Owner's Manual - Page 12

... into unauthorized hands, you have successfully erased the old programming. 2. The door will activate door until the LED starts to slowly blink. Press Program key . Programming Locate Your Opener's Programming Buttons and LED Opener 4. Press the Program key . 3. NOTE: Pressing any single button will automatically stop or start programming steps over. " Changing Your PIN...

Owner's Manual - Page 13

... LED goes off and the long LED flashes purple. NOTE: The garage door opener will not activate the door opener. 4 Optional Programming Clearing Memory FOR Remotes 1 Press the Program Set button on pages 9 and 12. PROGRAM - + 3 Press up arrow button (+) and down arrow button (-) simultaneously on the Powerhead and hold 2 seconds, round LED comes ON. G999-393 Manual...

Owner's Manual - Page 14

... on the transmitter is set to Intellicode® 1. 2 Press and release the Remote button 3 times. ***Repeat Step 2 to turn ON). 4 Optional Programming INTELLICODE® 1 REMOTES Remotes provided with this unit can operate other (Intellicode® 1) models of Genie® garage door openers .The default Intellicode® 2 setting must be changed to Intellicode® 1. (Follow...

Owner's Manual - Page 16

... LED displayed. - Check wiring and wire connections. Door should move very slowly. - ALWAYS keep the moving door in powerhead - Check for signal interference from operating it. Test opener monthly. An improperly balanced door increases the risk of travel, retest door opener. SAVE THESE INSTRUCTIONS WARNING • Garage door hardware (springs, cables, brackets, pulleys, etc...

Owner's Manual - Page 17

... CFL's may also be used. - Disconnect power to carriage, pull down and toward the door. Note: The opener will re-attach itself to door opener. • Test light operation. Disengaging and Engaging Carriage/Bullet Screw Drive Opener Belt/Chain Drive Opener Disengaged Engaged Disengaged Engaged To engage bullet to carriage. Remote Battery Replacement Replace remote...

Owner's Manual - Page 19

... Green Green Red LED LED LED LED LED LED Three Door Garage Single Garage Door • Determine which side of door components and tracks. Sensor modules CAN be adjusted to a slower speed in opposite directions. However, travel speed for the opener can be positioned further away from door opening if necessary to avoid sunlight but no further off...

Owner's Manual - Page 21

... and hold the wall console button until door is engaged into outlet used for binding. • If an operational problem exists, and opener will only run from remote. • Make certain carriage is completely closed . See pages 10-11. Door starts up . Check connections at powerhead terminals and at garage door. • Replace battery. See page...

Owner's Manual - Page 22

...® physical obstruction. Remove obstruction. WHAT TO DO • Be sure all door fasteners are tight. • Be sure garage door is in good repair, properly lubricated and balanced. • Be sure opener is less than 6-feet, opener configures programming for one-piece door is lowest speed setting. • If carriage travel . No response from unit...

Owner's Manual - Page 23

... d/b/a The Genie Company ("Seller") warrants to the original purchaser of the below identified, SilentMax® 1000/1200, CB 1000/1200, IntelliG® 1000/1200, PowerMax® 1200/1500, SC 1200/1500, TriloG™ 1200/1500, PowerLift® 900, or GPower™ 900 garage door openers, ("Product"), subject to provide necessary maintenance, normal wear and tear, or acts of God or...

Owner's Manual - Page 24

... other remotes or wall buttons Check out NEW ACCESSORIES and PRODUCTS; Genie-Net™ technology "tells" you! visit www.GenieCompany.com or call 1-800-35-GENIE. G999-393 Manual-ScrewBeltChain-EN indd 24 ™ 7/13/12 10 17 AM Garage Door Opener Accessories Looking for activation Upgrade with Revolution Series 1500, 1200 and 1000 Models...