Genie ChainLift 600 Support Question
Genie ChainLift 600 Support Question
Find answers below for this question about Genie ChainLift 600.Need a Genie ChainLift 600 manual? We have 1 online manual for this item!
Question posted by kweeden3 on August 8th, 2013
.5 Hp Genie Chainlift 600
is it possible to install this unit on a 9 x 12 sectional door ?
Current Answers
Related Genie ChainLift 600 Manual Pages
Owner's Manual - Page 1
...Models 1022/1024/1042
GARAGE DOOR OPENERS
Installer: Leave this manual with sectional doors.
Homelink® is a registered trademark of Johnson Controls Technology Company. Your Residential Opener comes with a Rail Assembly which is standard for up to close door. For use only with homeowner. Car2U® is a registered trademark of Lear Corporation. © The Genie Company 2010...
Owner's Manual - Page 2
... HAZARDS
READ THIS SAFETY INFORMATION
Garage doors are large, heavy objects that...PREVENTION
Keep people clear of opening while door is the safety alert ...install, repair or adjust springs or anything to play with the help you have questions or do NOT understand the information presented, contact The Genie Company or an authorized Genie® Dealer.
Operator must be done by a trained door...
Owner's Manual - Page 3
...* Operates door opener from inside garage. (Refer to each time the remote control is activated and automatically turns OFF 3 minutes later. PN# 3642036534, 02/26/2010 REV. 1
3 Turns ON when door is used. The door opener responds to section 3)
and Car2U® compatible. TABLE OF CONTENTS
SECTION PAGE SAFETY INFORMATION 2 OPENER FEATURES 3 SAFETY FEATURES 3 PRE-INSTALLATION CHECK LIST...
Owner's Manual - Page 4
..." installation. WARNING
To reduce the risk of aluminum, light-weight steel, fiberglass or glass panels?
Door springs, cables, pulleys, brackets and associated hardware are under extreme tension and can furnish you with a "bracing kit." (Refer to Section 2.)
WARNING
If your sectional garage door made of injury to persons or damage to these type doors. This opener is possible that...
Owner's Manual - Page 5
Use this opener only with SECTIONAL doors only.
PN# 3642036534, 02/26/2010 REV. 1
5 Pg. 17-18
3
6 Pg. 11
4 Pg. 14
Pg. 17-18
3
SAFE-T-BEAM®
MAX. 6" MIN. 5"
7
Pg. 12 SECTIONAL DOOR
WARNING To reduce the risk of injury to persons or damage to property - TYPICAL SECTIONAL DOOR INSTALLATION
5 Pg. 19
1 Pg. 13
TYPICAL SUPPORT BRACKET
(NOT PROVIDED)
FOR...
Owner's Manual - Page 6
... or run under automatic garage door. Death or serious injury can be pinned under moving do.or. • Never let ch ld use door opener controls. •Always keep moving door in tru t ons ... Staple
Rail Section Clamp
Door Arm
Wall Console
End Rail Section Center Rail Section
Pro Rail (Chain) Section
OR
Head Rail (Chain) Section
Pro Rail (Belt) Section
Head Rail (Belt) Section
6
PN#...
Owner's Manual - Page 9
... contain the same parts and be packaged with sectional doors. Remove the motor power head and place it , and • Away from all locks connected to the garage door before installing the opener.
3. Header Bracket Lag Srews
PN# 3642036534, 02/26/2010 REV. 1
9 Where possible, install the door opener 7 feet or more above the floor and avoiding contact with vehicles...
Owner's Manual - Page 11
... all ropes and/or cables and disable garage door lock NOW before continuing with installation (Fig. 1-8). Begin with Section 2 INSTALLATION. NOTE: Standing at the powerhead, facing the door, the bullet MUST be on the rail... and record it on warranty page. POWER HEAD & RAIL ASSEMBLY Assembly for BELT DRIVE OPENER NOTE: For power head and rail assembly locate Bag 1 from Box 1. Tighten belt...
Owner's Manual - Page 12
... OF TRAVEL
SECTIONAL DOOR
FROM HERE TO FLOOR
TRACK
NOTE: If header bracket location needs to be above door for header bracket (Fig. 2-1, d). A 2" x 6" board securely attached (board and fasteners not included) to garage framing. Mounting the header bracket.
• Hold header bracket against wall (Fig. 2-3). • Position bracket as your location for garage door opening, you need...
Owner's Manual - Page 13
...nuts.
• Carefully raise and lower door manually.
Place material on the garage construction, extra framing material (not provided)... 3642036534, 02/26/2010 REV. 1
13 Ensure door does not contact any section of power head or rail.
• Check that... similar device may be installed using (provided) lag screws (Fig. 2-6).
• On unfinished ceilings or open ceilings, straps may be...
Owner's Manual - Page 14
... bracing should be properly braced before mounting door opener. Use lag screws (not provided) for attaching door bracket.
short clevis pin & cotter pin
2. Connecting the arms.
• Slide carriage back and forth to improperly braced door. FIG. 2-9 Attaching door arms.
bolts as far apart as possible (Fig. 2-9). Contact door manufacturer or distributor for damage caused due to...
Owner's Manual - Page 15
...other wall control can cause the door to operate unexpectedly and the light not to the B (plus ) terminal. - WARNING Use of wall console. - White wire to the opener before installing wall console wires and wall console...Staples which are polarized.
2a. Your wire routing may be able to reach the garage door while standing at Wall Console.)
• Wall Console board screw connections are too ...
Owner's Manual - Page 17
...® SYSTEM INSTALLATION
FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM
WARNING There should be on sunny side whenever possible (Fig. 4-4).
• For multiple doors. - Determine which side of wood, etc. PN# 3642036534, 02/26/2010 REV. 1
17 NOTE: The opener will spend more time in opposite directions (Fig. 4-4). b) Blocks of garage receives most...
Owner's Manual - Page 19
...
2. PN# 3642036534, 02/26/2010 REV. 1
19 The door opener must be influenced if the Safe-T-Beam® is installed improperly, you to operate using
7/8" diameter hole. - Motor Cover ... your garage door opener permanently wired, with permanent wiring. WITH PERMANENT WIRING: Instructions for charges resulting from circuit. • Remove rear cover and motor cover.
- NOTE: The Genie Company ...
Owner's Manual - Page 20
...Section 10. CLOSE TRAVEL LIMIT 1. You can also use the "Open Travel Limit" button to move the door to move the door in damage to Carriage.
OPEN... Light
Open
Open
Set Limit
Travel Limit Button
Up Force
OPEN Control
Adjustment
To Garage Door
SET
LEARN...increase the door closing force is in the desired position, press and release the "Open SET Limit" SET button for unit to rail...
Owner's Manual - Page 21
... Keyed Emergency Release Operation Instructions • Place key in a failure of the opener or fully closing garage door manually will enable the correct carriage release action for the opener. NOTE: The next normal operation of the emergency release.
2.
Follow the remaining installation instructions for correct operation of emergency release kit. FIG. 6-4
Emergency release cable to...
Owner's Manual - Page 22
... not properly reverse. - Set the CLOSE force level at the minimum force required to open travel limit settings are erased. Once the desired level is installed. OPEN/CLOSE TRAVEL LIMIT
1. All close door without stopping. 4.
Testing.
• Open garage door using wall button. • When door contacts board, the door must stop
(within 2 seconds) and reverse direction returning to...
Owner's Manual - Page 23
... Door will stop . • Press button again. - FCC and IC CERTIFIED
This device complies with opener, including wall button, remote control, or Wireless Keypad.
3. To Garage Door
SET... allow children to operate 2 doors. Red LED will move in a residential installation.
However, there is no longer recognize any other which the receiver is moving door can program a maximum of twice...
Owner's Manual - Page 25
... the force or the limit of garage door opening. • Close door by using remote. - In center of travel, retest the door opener. ROUTINE MONTHLY MAINTENANCE
1. If door moves quickly, CONTACT A TRAINED DOOR SYSTEM TECHNICIAN. • Close the door. • Pull emergency release knob towards the opener to engage carriage. - check alignment (See section 5 ). PN# 3642036534, 02/26/2010 REV...
Owner's Manual - Page 27
... Company at 1-800-35-GENIE.
• Check door balance, condition, and door spring. • Check "OPEN FORCE" adjustment (See section 6 ). • WARNING: If you suspect a problem with the garage door hardware or springs, contact
an authorized Genie® Dealer or a trained door system technician, or contact The Genie Company at 1-800-35-GENIE. Opener runs, but door does NOT move . Remote...
Similar Questions
Garage Door Closing Without Pushing Remote Button
The garage door started closing without pressing any buttons. The first time it happened it went dow...
The garage door started closing without pressing any buttons. The first time it happened it went dow...
(Posted by bairrugs 2 years ago)
What Remote Do I Use For Powerlift Garage Door Opener Model Wr77 Serial No.08258
(Posted by tmski87 3 years ago)
Garage Door Opener Not Working
Green light and red light are on the safety"eye" When pushing wall, remote or key pad the screw driv...
Green light and red light are on the safety"eye" When pushing wall, remote or key pad the screw driv...
(Posted by scanty5 9 years ago)
Where Is The Learn Code Button Situated On The 3060l-07 Genie Garage Door Opener
Where is the learn code button situated on the 3060L-07 Genie garage door opener. Trying to intregat...
Where is the learn code button situated on the 3060L-07 Genie garage door opener. Trying to intregat...
(Posted by katiaella 10 years ago)
Why Is The Garage Door Opener Has Red Blinking Lights And Does Not Operate?
(Posted by aysegogini 10 years ago)