GE NX480 Support Question
GE NX480 Support Question
Find answers below for this question about GE NX480 - ITI, Caddx Wireless Motion Detector.Need a GE NX480 manual? We have 1 online manual for this item!
Question posted by hskim86204 on June 20th, 2014
No Transmission Between Panel And A Sensor.
Panel says "lost upstair" beeping intermittently. Changing bettery didn't solve the problem. How to fix the problem, or disconnect the sensor completely?
Current Answers
Related GE NX480 Manual Pages
Installation Instructions - Page 1
... within 100 feet of view, causing a temperature change in . Use motion sensors to walk across the sensor's field of the
panel. Actual acceptable transmitter range should be closed in a corner. s Do not mount the sensor near duct work or other large metallic surfaces which has an armed motion sensor. NX-480 Wireless Motion Sensor
Document Number: 466-1479 Rev. age area...
Installation Instructions - Page 2
...11 ft 2.4 m
4 ft
1.2 m
0 ft 0 ft
0 m 35 ft
8362G09A.DS4
Figure 3. NX-480 Wireless Motion Sensor
0 m 0 ft
TOP VIEW
11 m 6 m
0 ft
3 m
Person walking across the protected room.
s Allowed mounting height is between 3 and 5 ...up to 35 feet), and lower mounting provides better protection close to the motion sensor (see Figures 2 and 3). Animal Alley Lens Guidelines
The animal alley lens...
Installation Instructions - Page 3
...Wireless Motion Sensor
USE
WITH
ANIMAL ALLEY LENS
WALL TAMPER KNOCKOUT
USE WITH STANDARD LENS
8362G03A.DS4
Figure 4. Mark the location of the sensor.
2. Use wall anchors and screws to secure into place.Attach the sensor to mount the sensor... out and the grooved side facing in.
6. To change the lens, first remove the sensor from its mounting plate by aligning its mounting plate. Setting...
Installation Instructions - Page 4
...of desired areas.
To change slightly depending upon the sensitivity setting. Walk test the PIR to note that are completed, apply masking labels to the sensor's lens to verify proper...
For complete programming instructions, refer to activate the 60-second walk test mode.
2. Maintenance
At least once a year, the range and coverage should be blocked. NX-480 Wireless Motion Sensor
1....
Installation Instructions - Page 5
... operation.
Place the control panel in the new location. 4. Listen for correct response.
NX-480 Wireless Motion Sensor
To relocate a sensor: 1. Mount the sensor in test mode. Test a known good sensor at that may not cause harmful interference. 2. If the system does not respond, avoid mounting a
sensor at the same location. 2. Changes or modifications not expressly approved...
Installation Instructions - Page 6
NX-480 Wireless Motion Sensor
Page 6
Caddx Controls, Inc. 1420 North Main Street Gladewater, Texas 75647 Toll Free: 1-800-727-2339 FAX: (903) 845-6811
Caddx is a registered trademark of Caddx Controls, Inc.
Similar Questions
The Audible Countdown Warning Sometimes Occurs For No Apparent Reason
On two consecutive evenings the audible countdown warning came on without our having used any panel ...
On two consecutive evenings the audible countdown warning came on without our having used any panel ...
(Posted by flemingraf 1 year ago)
Disconnecting Smoke Detector
Have The GE ATP1000 and have a GE ESL429/449 detectors. Have one bad. How can I disconncet that one ...
Have The GE ATP1000 and have a GE ESL429/449 detectors. Have one bad. How can I disconncet that one ...
(Posted by crick1960 3 years ago)
Wiring Diagram Needed To Connect All Wires Inside The Motion Detector
Wiring diagram please
Wiring diagram please
(Posted by 4ports2 5 years ago)
I Changed The Batteries How Do You Reset The Detector
(Posted by mrcastillo13 9 years ago)
How Do I Replace The System Battery Of The Ge Simon 3?
(Posted by sinoffbisprof 12 years ago)