Craftsman 21829 Support Question
Craftsman 21829 Support Question
Find answers below for this question about Craftsman 21829 - Professional 10 in. Portable Table Saw.Need a Craftsman 21829 manual? We have 1 online manual for this item!
Question posted by kellystemple on November 16th, 2012
Trying To Find A Throat Plate For Table Saw Craftsman 218291. Not A Dado Plate.
The person who posted this question about this Craftsman product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Craftsman 21829 Manual Pages
Operation Manual - Page 1
Operator's Manual
10 in. TABLE SAW
Model No, 315.218290
_k WARNING: To reduce the risk of injury,the user must read and understandthe operator's manual before using this product. Customer Help Line: 1-800-932-3188 Seam, Roebuck and Co., 3333 BeverPy Rd., Hoffman Estates, IL 60179 USA Visit the Craftsman web page: www.seam.com!cmffsman 983000-693
7-15-05
Operation Manual - Page 15
...1 K. Throat Prate(2 its 1
Fig. 6
J. Throat PLate[1-1/8 in 1 F. x 3/4 in 1 H. Screw, M8 x 24 4 O. Throat Prate (1 in 3 N. Screw, 5/16-18 in 1 I. Guide Fence w_thGuide Block 2 B. Screw, #10 In.-32 x 3/4 In 3 M. Table Clamping Bracket 1 E. Post 1 R. Knob Bolt (1/2 In 4 D. Throat Plate (1-1/2 in . Thefolidwing items are includedwith your table saw:
@ D
F
d
A.
Operation Manual - Page 19
...; Loosen tha screws in a dry environTnent. Fig. 17
19 To unlock and move the table saw in the throat prate. • Liftthe throat plate from the body.
• Push the table saw cabinet. See To Store the Tab/e Saw A_ssories on the wheels.
• Push the saw to the right.
• Repeat shove steps with the holes in the...
Operation Manual - Page 20
... only to f_t "seated" position. • Remove the miter fence from the saw cabinet. • To install the miter fence to the slidingmiter table, Icesen the adjusting clamp knobso the bolt hasenough olsaranoa to slide _nthe table slot,
LOCKINGCLAMPS
LARGE WBRLEANDCEH
THROAT PLATE
SMALL
REAR RAIL
SUDII_ MITER TABt.EBASE
Fig. 19
WRENCH
Mount the...
Operation Manual - Page 22
ALWAYS align the rivingknife to the saw b/ade priorto turning on the table saw blade and rivingknifeare in alignment. TO INS'i'ALLBLADEGUARDASSEMBLY
See Figure 23. Proper installationof the blade guard assembly means that the saw .
• Lower the blade and remove the throat plate. • Make sure the bevel looldng leveris securelypushed to its full height by...
Operation Manual - Page 26
...be set so that the referencemark on the blade is at the front of the throat plate.
• Place a framing square (G) againstthe blade and alignwith referencemark on miter... back of miter table. TOCHANGETHEBLADEDEPTH
See Rgure 28. AN_I.ED
CHECKING SLIDING MITER TABLE AND MAKING ADJUSTMENTS
TO CHECK MITER BASE PARALLELISM See Figures 30 - 31.
• Unplug the saw.
• Set saw .
• ...
Operation Manual - Page 27
... degrees.
• Set _e miter fanes (H) at the rear of the throat plate. F
I
B Fig. 31
Fig. 32 27 See the ToAdjust Ou_k-Sl_> sent/on the mitsr table. Measure the distance between the front and rear of the blade, the miter table needs a|ignlng.Followthe adjustment procedures that follow.
• Remove framinQs,quare and...
Operation Manual - Page 35
... dado cuts. NOTE: TtT_sis the onlytype out that is a straight cross cut, read and understandthe sectionon straight cross cuts before procaed{ng. • Unplug the saw.
• Lower the blade and removethe screw holdingthe throat plate... miter gauge, it is too {argofor this type of the saw table behind the saw , Let the blade bu_d up to full speed beforefoeding the wood _,ntothe blade.
• ...
Operation Manual - Page 36
... come to avoid the risk of this tooL
NOTE: This saw cannot be used to make a bevel dado
CUt.
• Unplug the saw. • Remove the blade guard aseembly. • Ratlghtanthe two hex nuts. • Remove the saw . • Lower the blade and remove the screw holding the
throat plate in .). and check with your nearest Sears...
Operation Manual - Page 39
...shouldbe adjusted to resultin sedous personalinjury.
_i, WARNING: Do not use the 10-32 x 3/4 in the throat plate. Failureto heed this warning is mounted permanentlyon some routere and should be ...outfeed fence should not be facingthe front of the table.
• Atign the holes in the table with a screwdriver.
• Select the correcstize throat plate for the size of the foraying bit.
&#...
Operation Manual - Page 40
... point down toward the fi'ontof the saw blade, raise the blade guard, and
remove the throet plate.
• Make sure the bevel lockinglever...table sew has been adjusted at the factory for makingvery accurate cuts. De not overtighten. Check allcrearancesfor free blade rotation. In cutting operations, the scarewilt be set to bow up above the table surface.
Do not allow the throat plate...
Operation Manual - Page 41
...to btndwhich will increaserisk of the _vin 9 knife: • Unplug the saw.
• Raisethe saw blade byturningthe height/beveladiuating har_twheel¢ountsml_ckwisa.
• Lift the anti-kickback pawls ...and hex nutsat its base. To adjust:.
• Unplug the saw and raise the b_adeguard assambly.
• Remove the throat plate and the blade guard assembly.
• Move the shims to...
Operation Manual - Page 46
... balance, Blade is fed too fast Rip fence ismisaUgned. Saw is heeling.
Replace blade. Clean and wax mils. Adiust the dvlng knife with convex side to table surface.
46
Blade is not mounted securely. Adjust legs of injury,use recommended
4070331
Dado Throat Plate
dado and zero clearance throat plata when amp}eying
Item No. 9-22214 Micro...
Operation Manual - Page 48
TABLE SAW - TABLESAW
FORHEIGHT/BEVEALDJUSTMENT HANDWHEELR,EFERTORGURE0
FORRIPFENCEASSEMBLY, REFERTORGUREC
i
FORlEG STANDASSEMBLY, REFERTORGURBG
11
ld 12 44
8O 81
120
F) 0 o
0:
107 r_ ¢ c Q
( (
F
€
107 # FORMITERTABLEASSEMBLY, REFERTD RRUREB FORMITERGAUGE, REFERTONOTEF
CRAFTSMAN 10 in . MODEL NO. 315.218290 , FIGURE A" 10 in .
Operation Manual - Page 49
..._Vll 2 x 22 x I"P)..... 3
61 413051004
E-Ring (ETW8 1
62 0181010309
SpringPIate 1
63 0181010211
Back-up Plate 1
04 411072702 65 0181010606
* Nylon Nut (1/4-20 1 Shaft 1
66 0181010105
Bevel Gear 2
31 918101533570 GroundingLabel ... number in . Spacer 1
28 0181010504
112in. TABLE SAW - CRAFTSMAN 10 in all correspondenceregardingyour TABLE SAW or when orderingrepair parts.
Operation Manual - Page 50
...LIST - p_
CRAFTSMAN 10 in 7
0131010217...10-24 x 112 in . Contact your nearest Sears Ratan Store for Service Center information.
ny repairsrequiringdisaessm'o_yot your table saw requiressafety testing to the double insulationsystem possiblyceus'lng electricalshock or eLactrocu(ionA. TABLE SAW... Panel, Front 1 110 Cabinet Panel Plate, Front ........ 1
0181010264 452070018 0182010219...
Operation Manual - Page 51
.... MODEL NO. 815.218290 FIGURE B: SLIDING MITER TABLE ASSEMBLY
I I I I I I
% I I l
2o
k
,
\
\ \
\
j- Mey Be Purchased Locally 51 CRAFTSMAN 10 in 4 Slkla (upper 4
Slide (lower 4...10 rrcn., Pan Hd 8 "N_on Nut (5/32 In 2 "Flat Washer (M4 x 9 x 0.BT 2 Quick Stop 2 Eocentric Screw 2 Eccentric Screw 3 Miter Base 1 Guide Plate 2
"SetScrew (3/16-24 x 114 In.) ........ 4 HoLder Plate...
Operation Manual - Page 52
, CRAFTSMAN 10 in . MODEL NO. 315.218290 FIGURE C: RIP FENCE ASSEMBLY
8
[ey Part No. No. Rip Fence t * Screw
(12-14 x 1/2 in., Pen Hd.) ........ 2
Dowel Pin (1/4 in . TABLE SAW - Number
Description
Qty. x 18 ram)..... 1 Fence Roller 1
RollerPin (M6.35 x 38.1 ram) .. 1
* Screw
{10-24 x 1 in., Pe.nHd 1 Clamp, Rear 1 Roller Holder 1
CompressionSpring 1 RollerPin (M3.3 x 19.05 ram...
Operation Manual - Page 55
TABLE SAW - No. MODEL NO. 315.218290 FIGURE G: ROUTER ACCESSORIES
r_ey Part No. Number
DeaoripUon
Qty.
1 A181014605 Guide Fence w/Guide
10 018101025a-127 Throat Plate (2 in 1
Block (left)and Screws 1 11 0161010250-127 Throat Plate (1/2 in 1
2 A181014606 Guide Fence wlGutde
12 0181010254-127 Throat Plate (1-1/8 in 1
3 0181010257
4 4120110T1 5 0161010347 5 0161010349
Block (right)...
Operation Manual - Page 57
...TABLE SAW - side panel of the cabinet. No, Number
Description
1 4101717O6
• Screw {10-24x 1/2 2
2 412011020
* Washer (M5.2 x 14 x 1T 2
3 016101O201
Feet Plug (M34 x 8,4 x 14 2
4 0182010317-126 Upper Support Plate I
5 410031717
* Carriage Bolt (5/16 x 80 ram 10...in all correspondence
i
Key Part NO. CRAFTSMAN 10 in. MODEL NO. 315.218290
l rehgeamrdoindgelynoumrTbAeBrwLEillSbAeWfouonrdwhoenneoprdlaetreinatgtareophaeidr ptoartthse. Number
...
Similar Questions
Table Saw Model 218290
i need instruction to use sliding miter angles
i need instruction to use sliding miter angles
(Posted by shankarbn 9 years ago)
Zero-clearance Throat Plate
Can a zero-clearance throat plate be purchased or made for a Sears 21807 table saw? Where/How?
Can a zero-clearance throat plate be purchased or made for a Sears 21807 table saw? Where/How?
(Posted by danandloisk 10 years ago)
Safe Height For Table Saw Blade Above Material
What is the recommended safe height for the saw blade to protrude above the material being cut? I sa...
What is the recommended safe height for the saw blade to protrude above the material being cut? I sa...
(Posted by leon18666 10 years ago)
Table Saw Switch Malfunction
Today I pushed my switch on the table saw and it didn't turn off! I had to unplug the table saw. I s...
Today I pushed my switch on the table saw and it didn't turn off! I had to unplug the table saw. I s...
(Posted by gringoticahouse 11 years ago)
Dado Throat Plate
Im using a craftsman professional table saw model 315.218280 with a 8 inch dado blade, the dado blad...
Im using a craftsman professional table saw model 315.218280 with a 8 inch dado blade, the dado blad...
(Posted by erosrpella 11 years ago)