Brother International XR9550 Support Question
Brother International XR9550 Support Question
Find answers below for this question about Brother International XR9550.Need a Brother International XR9550 manual? We have 3 online manuals for this item!
Question posted by Bigberger on April 25th, 2022
I Received A Manuel With My New Brother Xr9550 Written In French. I Would Like T
I would like to get a manual written in English
Current Answers
Answer #1: Posted by SonuKumar on April 25th, 2022 9:50 PM
SonuKumar
Member since:
May 9th, 2021 Points: 16,619,310
Member since:
May 9th, 2021 Points: 16,619,310
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Brother International XR9550 Manual Pages
Operation Manual - Page 1
Operation Manual
Sewing Machine
Product Code: 888-E33/E34/E36/E37
KNOWING YOUR SEWING MACHINE SEWING BASICS UTILITY STITCHES APPENDIX
Be sure to read this document nearby for future reference. We recommend that you keep this document before using the machine.
Operation Manual - Page 3
...manual, or if you are being used or where oxygen is being sewn may ignite, resulting in injuries.
6 Special care is stored or in the machine falling, which could cause the needle to break.
• Do not push or pull the fabric when sewing... outlet when making any adjustments in the instruction manual:
• To unplug the machine, switch the machine to the symbol "O" position to an AC ...
Operation Manual - Page 4
...web site at www.brother.com
SAVE THESE INSTRUCTIONS
This machine is intended for household use or store the machine near children.
• The plastic bag that this machine, avoid direct sunlight ... (light-emitting diode) is damaged, it must be used.
• Always consult the operation manual when replacing or installing any assemblies, the presser feet, needle, or other hot objects.
•...
Operation Manual - Page 5
...parts 6 Needle and presser foot section 6 Operation buttons 7 Operation panel 7 Spool pin 8
USING YOUR SEWING MACHINE 9 Power supply precautions 9 Power supply 9 Foot controller 9 Sewing speed controller (for models equipped with character stitches 50
4. SEWING BASICS 25
SEWING 25 General sewing procedure 25 Selecting a stitch 25 Adjusting the stitch length and width 26 Starting to...
Operation Manual - Page 6
...-031
4 Monogramming foot "N"
XD0810-031
5 Zipper foot "I
R
9.
Memo
• About zigzag foot "J"; The product code is mentioned on the machine
with product code 888-E33/E34/E36/E37.
1 KNOWING YOUR SEWING MACHINE
ACCESSORIES
Included accessories
After opening the box, check that the following accessories are included. Note
(For U.S.A. MM
6. J
A
G
No.
N
7.
8. If...
Operation Manual - Page 7
... equipped with a flip chart on the model
you purchased, the following are available as optional accessories to
Open the compartment as illustrated below. KNOWING YOUR SEWING MACHINE
Optional accessories
For models equipped with an open it.
1 Flat bed attachment 2 Storage compartment
Note
• Store the accessories in the compartment when they are...
Operation Manual - Page 8
... (page 16) H Thread guide (page 12 and 17) I Thread guide cover (page 17) J Handle
Carry the sewing machine by its handle when transporting the machine.
Do not cover the air vent while the sewing machine is being used to manually raise and lower the needle. Needle and presser foot section
1 Bobbin winder (page 11) 2 Upper tension...
Operation Manual - Page 9
... of the selected stitch (1), the presser foot type to be sewn. KNOWING YOUR SEWING MACHINE For models equipped with type B LCD
1
1 Reverse/reinforcement stitch button Press this controller to reduce the stitch length; This manual uses the illustrations of sewing while the button is lowered in the opposite direction. Reverse stitches are displayed here...
Operation Manual - Page 10
... raise the spool pin.
■■Installing the spool pin
1 Insert the tab on the sewing machine or if the spool pin will not be used, return the spool pin to its storage position. KNOWING YOUR SEWING MACHINE
Spool pin
Press down until it locks into place.
■■Storing the spool pin
When...
Operation Manual - Page 11
... for a long period of electric shock, this plug is turned off the sewing machine and unplug the power supply cord.
(For U.S.A. Fire or electric shock may... (one way. These things may result.
If the cord or plug is turned on the machine.
KNOWING YOUR SEWING MACHINE
USING YOUR SEWING MACHINE
Power supply precautions
Be sure to install the proper outlet. WARNING
• Use only regular...
Operation Manual - Page 12
... is maintained after the machine is the foot controller's maximum sewing speed.
10
3 After the sewing machine has turned on,
release the "-" side of (1). KNOWING YOUR SEWING MACHINE
CAUTION
• When connecting the foot controller, be sure to turn off the sewing machine. 2 Holding the "-" side of (1) pressed, turn
on the sewing machine.
3 After the sewing machine has turned on the...
Operation Manual - Page 13
... unwound from the bottom to beep each time a key is pressed.
KNOWING YOUR SEWING MACHINE
CAUTION
• Only use the bobbin that the machine does not beep.
1 Turn off the sewing machine.
2 Holding the "-" side of
(3) pressed,
turn on the sewing machine.
3 After the sewing machine has turned on,
release the "-" side of the same type (part
code: SA156...
Operation Manual - Page 14
... bobbin may not be wound cleanly.
4 Put the bobbin onto the bobbin winder shaft and slide the bobbin winder shaft to the right. KNOWING YOUR SEWING MACHINE
CAUTION
• If the spool or the spool cap is too small for models equipped with the start / stop button) (for the spool, the thread...
Operation Manual - Page 15
... six times.
13 KNOWING YOUR SEWING MACHINE
Memo
• When the sewing machine is started or the
handwheel is wound, when the thread runs low it may tangle around the bobbin, the machine will make a
clicking sound;...8226; Not winding the bobbin properly may cause the thread tension to operate the sewing machine, connect the foot controller before turning on the shaft fits into the notch in...
Operation Manual - Page 50
... characters can be stored in memory even if you turn off the machine.
■■Adding new characters after sewing After sewing a combination of characters, you can add characters to the combination using the following procedure.
• For details on sewing characters, refer to "Sewing the character stitches" (page 50).
■■Combining characters
You can...
Operation Manual - Page 51
...
key) to the last character of the combination.
■■Making a new combination of a new combination.
3 Add characters by following the procedure described in "Combining characters" ...new combination.
1 Stitch width adjustment key XX The last character will display the characters that the character stitch indicator is entered as the first character of characters after sewing...
Operation Manual - Page 63
...new bobbin case (part code: XE7560-001), contact your nearest authorized service center.
• Make sure that you need additional help, the Brother Solutions Center offers the latest FAQs and troubleshooting tips. Be sure to refer to come off of the machine...not flush with the top surface of the machine. Sewing while the needle plate cover is scratched, otherwise the upper thread may become tangled...
Operation Manual - Page 67
... the race, or fabric is started . Symptom 2 : The upper thread is tangled, for example, in "Checking machine operations" to "Upper threading" (page 16). Symptom 4 : The fabric is correctly threaded.
8 Perform trial sewing with a new one of incorrect upper threading or sewing thin fabrics. If the needle or feed dogs contact the needle plate, the...
Operation Manual - Page 68
...).
7 If the needle is bent, replace it with a new one . • Refer to "Replacing the needle" (page 21).
6 Turn on the machine, and then press the needle position button to "Needle types ...to raise the needle before threading the sewing machine.
■■Remedy Thread the upper thread again correctly by following the procedure below .
1 Turn off the machine. 2 If the thread is tangled,...
Operation Manual - Page 76
Please visit us at http://support.brother.com/ where you can get product support and answers to frequently asked questions (FAQs).
English 888-E33/E34/E36/E37
Printed in Vietnam XG7396-001
Similar Questions
What Are The Default Settings For Brother Se 400 Embroidery And Sewing Machine
(Posted by sardskid 10 years ago)
Brother 17-stitch Free-arm Sewing Machine Lx2500 How To Set Tension
(Posted by laptoprustar 10 years ago)
Brother Sewing Machine Sq 9050 Manual Book
I have a brothers sewing machine sq9050 when Im trying to embroder letters it only sews one size how...
I have a brothers sewing machine sq9050 when Im trying to embroder letters it only sews one size how...
(Posted by kbmouser 10 years ago)
Brothers Nx-600 Sewing Machine Service/repair Manual
I am looking for the service/repair manual for the Brothers NX-600 sewing machine.
I am looking for the service/repair manual for the Brothers NX-600 sewing machine.
(Posted by Anonymous-125326 10 years ago)
How To Thread The Brother Limited Edition Project Runway Sewing Machine
ls2300prw manual
ls2300prw manual
(Posted by jjmaf0 10 years ago)