Bosch GRL160DHV Support Question
Bosch GRL160DHV Support Question
Find answers below for this question about Bosch GRL160DHV - Dual-Axis Self-Leveling Rotary Laser.Need a Bosch GRL160DHV manual? We have 1 online manual for this item!
Question posted by rws1200 on January 22nd, 2013
Remote
Replaced the 9 volt battery and laser doesn't recognize signal from remote..
Current Answers
Related Bosch GRL160DHV Manual Pages
Operating Instructions - Page 6
ALWAYS make sure that may result in traffic. Damage to the laser tool and/or serious injury to view the laser beam. DO NOT disassemble the laser tool. Modifying the laser tool may cause anyone to your mains-operated
(corded) tool or battery-operated (cordless) tool.
! DO NOT stare directly at persons or animals and do not stare into the eyes...
Operating Instructions - Page 7
...laser tool.
DO NOT mix old and new batteries.
Remove batteries if the device will not be
used for appropriate conditions will not occur in fire. A moment of inattention while operating a tool... tools. Use the correct tool for the particular type of the tool is encouraged to try to correct the interference by a qualified repair person using only identical replacement parts. Replace
...
Operating Instructions - Page 8
... outdoor plumb and alignment applications, such as leveling cabinetry, setting concrete forms, or leveling electrical outlets.
• Grading -
Always replace all batteries at the same time. Use both lasers simultaneously to generate a crosshair for the tool. Note that the two pairs of batteries are recommended for level and plumb alignment applications, such as grading driveways...
Operating Instructions - Page 9
...of the rotational laser level 14 Tripod mount 5/8- 11 15 Battery compartment, rotational
laser level Detector/Remote Control
16 Control panel, laser receiver 17 Display 18 Reception area for the laser beam 19 Center mark 20 Serial number of laser receiver 21 Battery compartment, laser receiver Operating controls, rotational laser level 22 Control Panel, Horizontal Laser
Beam (X-axis) 23 Button for...
Operating Instructions - Page 10
...11
Remote Control with Laser Receiver-detector
Working Range (Radius)
Laser Receiver with independent and simultaneous operation. Positioning, horizontal or vertical (for laser receiver 50 Tripod* 51 Protective Case 52 Wall Mount
*The accessories illustrated or described are not included as standard delivery. Working Range (Diameter)
With Laser Receiver . . . .up to 1000ft(305m)
Self Leveling...
Operating Instructions - Page 11
... these settings when a command is turned off with Automatic Leveling
Position the tool on /off the leveling unit, which the tool stands deviates by more than 6° the tool beeps, the LED flashes red once per second, and the laser beams flash once per second, to save battery life. Current settings are not retained when power is...
Operating Instructions - Page 12
... the remote control. Rotation and Line Dithering/Scan Mode
The GRL160DHV rotary laser tool has two basic operating modes for marking.
Rotation Mode
The laser beam is vertical to take place. Rotation mode is used for example, outdoors in either the level or plumb applications.
Decrease speed to improve laser beam visibility, especially for the self-leveling to the rotational axis...
Operating Instructions - Page 13
... beam.
-13-
Leveling
In the level position, the tool automatically self-levels within self-leveling range, it stops beeping, the LED turns green, and the laser beam stops flashing. When the tool is not visible, use the laser detector to abuse. It is also recommended that may be mounted on a commercially available tripod and placed in low battery or power standby...
Operating Instructions - Page 14
... the original wall.
11. Use the level (horizontal) Line Dither/Scan position arrows 23 and 25 to the off the laser beam and the tool. Turn the power switch to position the laser beam on the vertical surface, as in the off position before proceeding to position the level laser beam at a height exactly halfway between...
Operating Instructions - Page 15
..., turn on the rotational laser level. Its receiving (detecting) function responds better to a grade/leveling rod.
-15-
As an example, do not leave it to the GRL160DHV laser tools rather than any other conditions when the beam is complete.
17. In case of extreme temperatures or variations in temperature, allow the laser receiver to adjust to the...
Operating Instructions - Page 16
... tool controls are turned on , Coarse resolution, Level laser, Spin mode
X
Level laser, Spin mode, Detector off
3. Laser Detection To turn on the RF remote control/laser receiver-detector LCD display. X
Beeper on, Laser detector on . The unit emits a single beep, and icons in Spin mode, at the slowest speed. On startup, the laser detector resolution is activated, but the GRL160DHV...
Operating Instructions - Page 17
... approx. 4 hours. Level laser detection
Plumb laser detection
Note: Laser detector orientation depends on the tool
Tool leveled in locating the laser beam:
• Rapid beep - Locate the laser beam, using the red sensor panel on the display 17, the laser receiver can still be operated for operation Self-Leveling range exceeded Leveling range of the arrow. X
Laser detector power off...
Operating Instructions - Page 18
Applications
Level, Plumb, Align (Carpentry)
Level (Concrete)
Level (Drop Ceiling
Level (Framing)
Plumb (Concrete)
Plumb (Framing)
Grade (Concrete)
Align (Flooring)
Align (Framing)
Align (HVAC)
Align (Tiling)
-18-
Operating Instructions - Page 19
... approximate height at another location. When mounting to a T-bar framing or beam, slide the slot on the back side of the bar and using the GRL160DHV laser tools outdoors or in intense sunlight.
The brightness intensification can be attached, wall, T-bar framing or beam.
3. These glasses are particularly useful when using the height...
Operating Instructions - Page 20
... regulations.
-20-
Wipe off debris using a moist and soft cloth. The unit, accessories, packaging & used batteries should be sorted for Bosch power tools.
ENVIRONMENT PROTECTION Recycle raw materials & batteries instead of disposing of the tool.
In case of the laser in the supplied protective case. Regularly clean the surfaces at all correspondence and spare parts...
Operating Instructions - Page 21
.../BERGER DEALER OR IMPORTER.
-21- If you can return it to BOSCH dealer within 30 days of the date of purchase. BOSCH will replace your laser or measuring tool product fails solely due to the extent permitted by law, any time during the first year after purchase. SELLER'S OBLIGATION AND YOUR REMEDY ARE...
Similar Questions
Is This Tool Supposed To Vibrate? Mine Is Not At All
I have a sander that seems to only blow air, how do I adjust it to make it work into the wood more?
I have a sander that seems to only blow air, how do I adjust it to make it work into the wood more?
(Posted by wjbranstner 7 years ago)
Grading With The Grl 160dhv
The instructions reference grading but do not provide any detail on how to set up the laser, how do ...
The instructions reference grading but do not provide any detail on how to set up the laser, how do ...
(Posted by wbv 8 years ago)
Self Leveling
This unit won't self level when in the horizonal position and won't self level either way without fr...
This unit won't self level when in the horizonal position and won't self level either way without fr...
(Posted by mattsue 10 years ago)
Grl145hv Just Keeps Beeping. Cal Works Only In Mode Ii Not I
GRL145HV will not self level just keeps beeping when in calibrate only mode II will move the beam mo...
GRL145HV will not self level just keeps beeping when in calibrate only mode II will move the beam mo...
(Posted by dustymutt 11 years ago)