Bosch GRL160DHV Support Question
Bosch GRL160DHV Support Question
Find answers below for this question about Bosch GRL160DHV - Dual-Axis Self-Leveling Rotary Laser.Need a Bosch GRL160DHV manual? We have 1 online manual for this item!
Question posted by wbv on May 24th, 2016
Grading With The Grl 160dhv
The instructions reference grading but do not provide any detail on how to set up the laser, how do you do that?
Current Answers
Answer #1: Posted by Odin on May 24th, 2016 5:39 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,660
Member since:
April 10th, 2010 Points: 41,236,660
See "Setting Up the Tool" at this manual page: http://bit.ly/1XT2v5Q. If you have further questions I suggest you call Bosch--see the contact information here: https://www.contacthelp.com/bosch/customer-service.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Bosch GRL160DHV Manual Pages
Operating Instructions - Page 6
... the risk of the warnings listed below may result in all of exposure to your laser tool. Serious eye injury could result.
General Safety Rules
!
WARNING
Read all instructions listed below refers to laser radiation. Failure to follow all instructions. The term "tool" in hazardous radiation exposure. WARNING
The following labels are no user serviceable parts inside...
Operating Instructions - Page 7
... of children and do the job better and safer. The correct tool will not occur in accordance with these instructions to be improperly mounted. Store idle tool out of the reach of inattention while operating a tool may cause harmful interference to operate the laser tool. Use of parts and any battery terminals.
Do not use common...
Operating Instructions - Page 8
... or Line Dither/Scan laser for indoor and outdoor plumb and alignment applications, such as leveling cabinetry, setting concrete forms, or leveling electrical outlets.
• Grading - Preparation
Inserting/Replacing the Battery
ALWAYS turn off , until the batteries are stacked.
Low Battery Indicator
The LED flashes yellow when 25 percent of the tool.
To open the battery...
Operating Instructions - Page 9
... product features shown refers to the illustration of line length (vertical laser beam)
-9- Rotational Laser Level
1 On/off switch for rotational laser level 2 LED for operating condition 3 Control panel of the rotational laser level 4 Handle 5 Warning label, laser radiation
exit opening 6 Outlet opening of the horizontal laser
beam (X-axis) 7 Horizontal laser beam (X-axis) 8 Outlet opening of...
Operating Instructions - Page 10
... target plate 49 Holder for line operation 360°
Laser Class Class IIIa Laser Type 635nm,
Stand by Operation after 20 min. Working Range (Diameter)
With Laser Receiver . . . .up to 1000ft(305m)
Self Leveling Range Horizontal and Vertical Up to +/- 6°
Leveling Accuracy
Level (horizontal): Minimum Factory Accuracy 0.167mm/m
(±0.002004in/ft)
Typical Horizontal Accuracy up...
Operating Instructions - Page 11
... for three seconds. because the surface on , the automatic leveling function automatically compensates irregularities within the self-leveling range up green.
2. Turn on the Tool
1. A beep and a single "chirp" confirm the command. Power Standby Mode
When commands are not received for 20 minutes, the GRL160DHV automatically enters the power standby mode to ±6°. In...
Operating Instructions - Page 12
... the level or plumb plane by applying the laser receivers' Remote-control function.
This effect can be necessary to take place. Rotation and Line Dithering/Scan Mode
The GRL160DHV rotary laser tool has two basic operating modes for example, outdoors in the dithering mode, a laser receiver-detector may be aligned on , it possible to the rotational axis.
1. The laser...
Operating Instructions - Page 13
... a steady green, and the beeping stops.
Therefore, check the accuracy of the working area.
Note: The out-of -level indicator overrides the low battery or power standby mode indicator. Calibration
Although the GRL 160DHV laser tools are calibrated to deviations. Ensure the calibration port faces away from exterior influences, device specific influences (such as a wall...
Operating Instructions - Page 14
... match the height of C, then proceed to step 14.
14. Otherwise, continue to the off position. Turn off the laser beam and the tool. Repeat steps 7 and 8 until the beam is to position the laser beam on the level laser beam, then check the height of D with the front facing the vertical surface. Use the...
Operating Instructions - Page 15
...improved finding of the level laser beam automatically calibrates the plumb laser beam. Attaching the RCR1 to a grade/leveling rod.
-15-
Note: Complete calibration of the laser beam. The following diagram...the GRL160DHV laser tools rather than any other conditions when the beam is used to locate the level or plumb laser beam. Position the laser receiver at the height of the laser beam...
Operating Instructions - Page 16
...detector on , Fine resolution, Level laser, Spin mode
-16- Y
Plumb laser, Line Dither/Scan Mode, Detector off , Laser detector on , Fine resolution, Level laser, Spin mode
X
Level laser, Line Dither/Scan Mode, Detector off
X
Beeper off
3.
Commands made from the tool controls are turned on .
On startup, the laser detector resolution is activated, but the GRL160DHV and RCR1 have not...
Operating Instructions - Page 17
... is aligned with the center of the vertical laser exceeded
Tool In stand-by moving the laser detector in the direction of the arrow. When the beam is a double beep for approx. 4 hours.
The base unit emits sounds to aid in /ready for operation Self-Leveling range exceeded Leveling range of the detector panel, both arrows...
Operating Instructions - Page 18
Applications
Level, Plumb, Align (Carpentry)
Level (Concrete)
Level (Drop Ceiling
Level (Framing)
Plumb (Concrete)
Plumb (Framing)
Grade (Concrete)
Align (Flooring)
Align (Framing)
Align (HVAC)
Align (Tiling)
-18-
Operating Instructions - Page 19
... are particularly useful when using the GRL160DHV laser tools outdoors or in brightly lit environments.
• Do not use the laser viewing glasses as safety goggles. Use with Accessories
Working with Wall Mount (Optional Accessory)
The durable metal wall mount 51 provides a flexible, yet sturdy means of positioning the tool in intense sunlight. To ensure the...
Operating Instructions - Page 20
... to any cleaning agents or solvents. In case of the laser in accordance with the latest regulations.
-20- The unit, accessories, packaging & used batteries should be sorted for Bosch power tools.
Keep the tool clean at the exit opening of repairs, send in the tool packed in the supplied protective case. Regularly clean the...
Operating Instructions - Page 21
... does not apply if your laser or measuring tool product that has failed when used in conformance with product instructions and warnings, with a new laser or measuring tool product of comparable features, for... carelessly handled, or misrepaired by persons other than Seller or Seller Authorized Service providers. SELLER'S OBLIGATION AND YOUR REMEDY ARE FURTHER LIMITED AS FOLLOWS: • 30...
Similar Questions
How Can I Clear The Error 41 When Trying To Run The Self Clean Cycle?
(Posted by kvool 3 years ago)
Self-cleaning Does Not Allow You To Simultaneously Press Bake And Broil!
self-cleaning does not allow you to simultaneously press bake and broil! Unit just beeps 3 times whe...
self-cleaning does not allow you to simultaneously press bake and broil! Unit just beeps 3 times whe...
(Posted by perrea 9 years ago)
Self Leveling
This unit won't self level when in the horizonal position and won't self level either way without fr...
This unit won't self level when in the horizonal position and won't self level either way without fr...
(Posted by mattsue 10 years ago)
Grl145hv Just Keeps Beeping. Cal Works Only In Mode Ii Not I
GRL145HV will not self level just keeps beeping when in calibrate only mode II will move the beam mo...
GRL145HV will not self level just keeps beeping when in calibrate only mode II will move the beam mo...
(Posted by dustymutt 11 years ago)
Has Anyone Tried To Paint The Worn Knobs On Their Bosch Dual Fuel Range?
Like many people, the knobs on my Bosch Dual Fuel Range are showing wear after only two months. Si...
Like many people, the knobs on my Bosch Dual Fuel Range are showing wear after only two months. Si...
(Posted by natemom 12 years ago)