Bosch GRL145HV - NA Horizontal And Vertical Electronic Self-Leveling Ro Support and Manuals
Get Help and Manuals for this Bosch item
View All Support Options Below
Free Bosch GRL145HV manuals!
Problems with Bosch GRL145HV?
Ask a Question
Free Bosch GRL145HV manuals!
Problems with Bosch GRL145HV?
Ask a Question
Most Recent Bosch GRL145HV Questions
Self Leveling
This unit won't self level when in the horizonal position and won't self level either way without fr...
This unit won't self level when in the horizonal position and won't self level either way without fr...
(Posted by mattsue 10 years ago)
Popular Bosch GRL145HV Manual Pages
Operating Instructions - Page 3
... of procedures other laser tools could result. WARNING
Read all instructions listed below refers to laser radiation. The laser viewing glasses are made aware of the dangers of exposure to your convenience and safety. Failure to persons being blinded. WARNING
The following labels are no user serviceable parts inside. DO NOT place the laser tool in serious...
Operating Instructions - Page 4
... sense when operating a tool.
Electrical safety
! Remove batteries if the device will do not allow children to operate the laser tool. Use safety equipment. Tools are caused by a qualified repair person using only identical replacement parts. Service
Have your application.
-4- Certain cleaning agents such as dust mask, non-skid safety shoes, hard hat, or hearing...
Operating Instructions - Page 5
... removing and replacing the batteries. Always replace all batteries at a sloped angle for extended periods. The LED flashes, and continues to the representation on the bottom of the battery compartment. The laser beam emitting from the tool when not using it for indoor and outdoor level applications, such as leveling cabinetry, setting concrete forms, leveling electrical outlets...
Operating Instructions - Page 6
... Compliance Class II Laser Beam Power . . . . .635nm, 1mW max.
Dithering Settings 20 deg. +/-...laser
Horizontal 11s (full range) Laser receiver- Leveling Range Up to +/- 6° RF remote
Level Settling Time
control range . . .Up to -10C), the high rotation speed spec...Laser Aperture 4 Power Switch 5 Laser Controls 6 Battery Compartment 7 5/8-11 tripod mount 8 Calibration Controls 9 Manual...
Operating Instructions - Page 7
...set it on a level and firm support, or attach it in effect, and returns to these settings when a command is within the self-leveling range up to work (see "Leveling Accuracy").
• Switch the tool off the laser...the reference points upon re-leveling.
-7- A beep and a single "chirp" confirm the command.
To avoid errors by more than 10mm @ 100m Precision setting . .Course: +/- 3mm...
Operating Instructions - Page 8
... not be necessary to accurately locate the beam. Because of -level indicator overrides all other indicators.
Rotation mode is used for example, outdoors in faster speed. It is poor or nonexistent (for indoor applications. Operating Modes-
Rotation and Dot/Dithering
The GRL145HV rotary laser tool has two basic operating modes, the Rotation Mode and...
Operating Instructions - Page 9
...the tool each time before leaving the factory, they contain many precision-machined parts that the unit will not self-level when in the point, dither or rotation modes. When in step 4. Rotate...keypad laser on the vertical surface of the next few steps is in self-leveling mode. Line I Side I must be square (90°) to be put into the manual slope mode by a Bosch after-sales service ...
Operating Instructions - Page 10
...-Detector
The following diagram
Beeper On/Off
Detector Laser Beam Locator Low Battery Indicator
Fine Resolution Coarse Resolution
Level Spin Mode/ Speed Select Level Line Dither/Scan Mode
CAL Calibration Mode
Manual Slope Mode
illustrates the RCR2
remote control.
-10- The following diagram illustrates RCR2's LCD
The GRL145HV can also
display icon
be operated using...
Operating Instructions - Page 11
... beep once to indicate that the unit is activated, but the GRL145HV and RCR2 have not been turned on. The unit will move the ...level or plumb laser beam.
3. Turn on /off
CAL
Level laser detection
Plumb laser detection
The bracket's clamp is in the point, dither or rotation modes. The laser dot or dithering line can be used to put the tool into manual slope mode by pressing the laser...
Operating Instructions - Page 12
... exit the calibration mode, press the keypad calibration axis I and Axis II buttons on the RCR2's laser receiver-detector function, press the coarse/fine select button. The tool can be put into calibration mode ....
-12- On startup, the detection resolution is coarse, with the center of the beam. Laser Detection To turn off the RCR2, press its power on the RCR2. The tool will beep three...
Operating Instructions - Page 14
... with intended laser line.
2. This makes the red light of the bar and using the GRL145HV laser tools outdoors or in brightly lit environments.
• Do not use the laser viewing glasses as...is even with Tripod (Optional Accessory)
A tripod 26 offers a stable, height-adjustable measuring support. Choose the surface on the underside of the mount over an 8" / 20 mm vertical extension range...
Operating Instructions - Page 15
... procedures, repair should be carried out by an authorized aftersales service center for... environmentally friendly recycling in particular, and pay attention to any cleaning agents or solvents. The unit, accessories, packaging & used batteries should be sorted for Bosch...parts orders, please always include the 10-digit article number given on the type plate of the laser...
Operating Instructions - Page 16
... TO LIABILITY FOR LOSS OF PROFITS) ARISING FROM THE SALE OR USE OF THIS PRODUCT. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS ... YOUR LOCAL BOSCH OR CST/BERGER DEALER OR IMPORTER. BOSCH will replace your laser or measuring tool product that has failed when used in conformance with product instructions and warnings, with a new laser or measuring tool...
Bosch GRL145HV Reviews
We have not received any reviews for Bosch yet.