Bosch 1508 - 8 Gauge Unishear Shear Support and Manuals
Get Help and Manuals for this Bosch item
Most Recent Bosch 1508 Questions
Bosch 1508 Videos
Video Tour of 1508 Appaloosa, Big Bear City, CA, Real Estate
Duration: 6:18
Total Views: 1,283
Duration: 6:18
Total Views: 1,283
Popular Bosch 1508 Manual Pages
Operating Instructions - Page 2
...INSTRUCTIONS
Work Area
Keep your hair, clothing, and gloves away from an outlet. If it still does not fit, contact a qualified electrician to lose control.
Personal Safety
Stay alert, watch what you to install a polarized outlet.
Keep handles dry, clean and free from
heat, oil, sharp edges or moving parts... to "Recommended sizes of this manual. Do not operate power tools ...
Operating Instructions - Page 3
... your legs.
Secure the material being cut. Use the correct tool for Shears
Hold tools by qualified repair personnel. Any tool that if contacted can cause hearing loss. If damaged, have the tool serviced before using this manual.
Follow instructions in a risk of unauthorized parts or failure to control. Use of injury.
Do not touch cutters...
Operating Instructions - Page 4
... greater than the rated capacity of the shear. Replace worn cutters.
Sharp cutters minimize stalling.
! Do not use of the shear. WARNING
Some dust created by power sanding, sawing,
grinding, drilling, and other masonry products, and
• Arsenic and chromium from sharp metal edges or strips while shearing metals. Sharp metal edges can pierce the jacket of...
Operating Instructions - Page 5
...
Rotational speed, at no load
Revolutions or reciprocation per minute
0
Off position
Zero speed, zero torque...
1, 2, 3, ...
This symbol designates that this tool is increasing from 0 setting
Arrow
Action in the direction of arrow
Alternating current
Type or a characteristic of current
Direct current
Type or a characteristic of current
Alternating or direct current...
Operating Instructions - Page 6
...SIDE HANDLE (Model 1508 only)
FOOTPLATE
PLUNGER UPPER SHEAR BLADE LOWER SHEAR BLADE
SETTING SCREW FLAT WASHER LOCKWASHER UPPER BLADE SCREW (A) FOOTPLATE
LOWER BLADE SCREW (B)
BLADE ADJSTMENT SCREW
Model number Shear Capacities Mild Steel Most Stainless Most Aluminum
1507 Trim Cut 10 (.135") 12 (.105")
(.157")
1508 Trim Cut 8 (.165") 10 (.135")
(.162")
NOTE: For tool specifications refer to...
Operating Instructions - Page 7
... of its parts.
Premature blade failure will reduce wear on standard sheet metal specifications. The horizontal clearance is independent of the thickness of the table provided below. VERTICAL CLEARANCE
UPPER BLADE
LOWER BLADE
HORIZONTAL CLEARANCE = MAXIMUM CLEARANCE
Operating Instructions
GENERAL INFORMATION Following a few simple tips will occur when the shear is under...
Operating Instructions - Page 8
...operation. For very thick materials (8 and 10 gauge shears), easier starts and longer blade life can be ... dull results!
If the shear does not cut correctly, recheck for instructions.
3. For clean and fast cuts, hold the shear so that the upper (...Model 1508 only) The side handle used to guide and balance the tool can be realized if the working surface of angles with the shear...
Operating Instructions - Page 9
...replaced at Bosch Factory Service Center or Authorized Bosch Service...key 1/8" (3mm) * Side handle (Model 1508 only)
(*= standard equipment) (**= optional ...parts.
Ventilation openings and switch levers must use 3-wire
extension cords that is capable
of the motor, we recommend every two to use. BEARINGS After about 300-400 hours of foreign matter. NOTE: The smaller the gauge...
Parts List - Page 2
SHEAR 1508 ... 83
84
A 650 A 651 A 652 A 653 A 654 A 655 A 656 A 657 A 658 A 800
PART NO. Brush set
A= Accessories
-9- PCS/UNIT
2 916 011 013
1
2 910 141 479
1
2 912 041 203
1
2 915 ...Screw Screw Screw Screw Instruction plate Shim Needle bearing Washer Screw Lock washers Screw Handle Allen Key 5mm Allen Key 3mm 10 mm open end wrench Turning pin Set gauge Grinding gauge Grease gun Grease 50...
Bosch 1508 Reviews
We have not received any reviews for Bosch yet.