Bosch 1508 Support Question
Bosch 1508 Support Question
Find answers below for this question about Bosch 1508 - 8 Gauge Unishear Shear.Need a Bosch 1508 manual? We have 2 online manuals for this item!
Current Answers
Answer #1: Posted by freginold on July 15th, 2015 8:29 AM
freginold
Member since:
December 20th, 2011 Points: 23,252,805
Member since:
December 20th, 2011 Points: 23,252,805
Hello, it looks like just about every tool site is out of stock on the 1508. GotGreatTools.com may have one; you have to call them to see about availability.
There is a factory-refurbished 1508 for sale right now on eBay, I think that's as close as you're likely to get.
There is a factory-refurbished 1508 for sale right now on eBay, I think that's as close as you're likely to get.
Related Bosch 1508 Manual Pages
Operating Instructions - Page 2
...THESE INSTRUCTIONS
Work Area
Keep your personal safety.
There is "OFF" before turning the tool "ON". Never use tool while tired or under the influence of electric shock. A wrench or a key that...to your hair, clothing, and gloves away from oil and grease.
Before plugging in tools that is unavoidable, a Ground Fault Circuit Interrupter must be used for the three wire ...
Operating Instructions - Page 3
... loss of injury. Use only accessories that may be controlled with care.
Follow instructions in the hands of electric shock or injury. Safety Rules for Shears
Hold tools by taking frequent rest periods. Wear ear protectors when using . Do not touch cutters or reach below
-3- Many accidents are dangerous in the Maintenance...
Operating Instructions - Page 4
... bricks and cement and other masonry products, and
• Arsenic and chromium from chemicallytreated lumber.
Do not cut material greater than the capacity of the shear may cause damage to
cause cancer, birth defects or other construction
activities contains chemicals known to the cutting edges of rotating bit. Protect the cord...
Operating Instructions - Page 5
... listed by Underwriters Laboratories, and listed to warning messages
Ni-Cad RBRC seal
Designates Ni-Cad battery recycling program
This symbol designates that this tool is increasing from 0 setting
Arrow
Action in the direction of arrow
Alternating current
Type or a characteristic of current
Direct current
Type or a characteristic of current
...
Operating Instructions - Page 6
... SCREW (A) FOOTPLATE
LOWER BLADE SCREW (B)
BLADE ADJSTMENT SCREW
Model number Shear Capacities Mild Steel Most Stainless Most Aluminum
1507 Trim Cut 10 (.135") 12 (.105")
(.157")
1508 Trim Cut 8 (.165") 10 (.135")
(.162")
NOTE: For tool specifications refer to the nameplate on your tool. -6- WARNING
Disconnect the plug from the power source before making...
Operating Instructions - Page 7
...of the metal being cut.
For hard and brittle materials (i.e.
With the tool unplugged from the shear.
Always direct the cord toward rear of the blades is under the load... from the power source while making adjustments
Insert lower shear blade in groove provided in the footplate and upper shear blade in contact with the lower blade screw (B). Gauge 8 (.164")
10 (.134") 12 (.104") 14...
Operating Instructions - Page 8
...very thick materials (8 and 10 gauge shears), easier starts and longer blade life can be threaded into the front housing on either side of the tool, depending on both the tool and the operator.
1. BM ...3609929846 8/01 8/21/01 8:31 AM Page 8
SIDE HANDLE (Model 1508 only) The side handle used to guide and balance the tool...
Operating Instructions - Page 9
...gauge number, the heavier the cord.
To maintain peak efficiency of
internal wires and components which become noisy (due to heavy load or very abrasive material cutting) should be used . Bearings which
could cause serious hazard.
WARNING
To avoid accidents always disconnect the tool... key 1/8" (3mm) * Side handle (Model 1508 only)
(*= standard equipment) (**= optional accessories)...
Parts List - Page 2
... plate Shim Needle bearing Washer Screw Lock washers Screw Handle Allen Key 5mm Allen Key 3mm 10 mm open end wrench Turning pin Set gauge Grinding gauge Grease gun Grease 50 gm. PART NO. NO. NO.
20/31 20/32 20/33 20/34 22 25 28 29 30 ... 63 66 69 71 75 77 78 79 80 83
84
A 650 A 651 A 652 A 653 A 654 A 655 A 656 A 657 A 658 A 800
PART NO. SHEAR 1508 (Continued)
POS. Brush set
A= Accessories
-9-
Similar Questions
Speed Control Dial Not Working Machine Runs On High
changed speed governor control unit and unit still runs on high and speed dial does not
changed speed governor control unit and unit still runs on high and speed dial does not
(Posted by regionalrestoration 6 months ago)
Runs But Not Impact
My Bosch 11316evs sds model 0611316739 runs but the impact is really weak even when the speed is up ...
My Bosch 11316evs sds model 0611316739 runs but the impact is really weak even when the speed is up ...
(Posted by arroyojorge421 5 years ago)
Is This Tool Supposed To Vibrate? Mine Is Not At All
I have a sander that seems to only blow air, how do I adjust it to make it work into the wood more?
I have a sander that seems to only blow air, how do I adjust it to make it work into the wood more?
(Posted by wjbranstner 7 years ago)
Grading With The Grl 160dhv
The instructions reference grading but do not provide any detail on how to set up the laser, how do ...
The instructions reference grading but do not provide any detail on how to set up the laser, how do ...
(Posted by wbv 7 years ago)
Bosch 1347a Armature Burnout
How to contact Bosch about premature failure of armature? Brushes not worn. Few operating hours des...
How to contact Bosch about premature failure of armature? Brushes not worn. Few operating hours des...
(Posted by energyman00 13 years ago)