Xerox 4540 - Phaser Copystation Support and Manuals
Get Help and Manuals for this Xerox item
Popular Xerox 4540 Manual Pages
Service Manual - Page 104
...:Not Installed
*
*
*
*
*
* Change Supervisor Password
*
*
* Change User Password
*
*
*
*
*
* Boot Sector Virus Protection [Disabled]
*
*
*
*
*
*
*
*
*
*
*
*
* * Select Screen
*
*
* ** Select Item
*
*
* Enter Change
*
*
* F1 General Help
*
*
* F10 Save and Exit *
*
* ESC Exit
*
*
*
*
*
*
*
2-70
Sun Fire X4500/X4540 Server Service Manual •...
Service Manual - Page 119
..., the following error message appears when the system tries to reach the PXE server:
PXE-ECI: Base code ROM-ID structure was not found. Chapter 2 Powering On and Configuring BIOS Settings 2-85 On-board SATA controllers 0 through 3
2.
2.21
BIOS ROM Memory
In systems that have multiple PCI cards installed, and with this problem is 128...
Service Manual - Page 148
.../X4540 Server Service Manual • May 2010 Note -
For an updated list of the cover.
▼ To Replace the Front Indicator Board (FRU)
The front indicator board supports the front panel... the qualified part numbers for assistance. Be sure you suspect the ribbon cable is a FRU and should be replaced only by qualified service technicians.
Contact your Sun Service representative for ...
Service Manual - Page 160
... in the server is not supported, and causes the System Fault LEDs to remove and replace a power supply unit (PSU). Hot-swappable means you do not need to change over time.
These part numbers are extremely sensitive to bare metal on the service label.
3-40
Sun Fire X4500/X4540 Server Service Manual • May 2010 if...
Service Manual - Page 164
...supply into the closed position.
3-44
Sun Fire X4500/X4540 Server Service Manual • May 2010 To replace the cable management assembly if necessary. Use the power cord retaining ...docs depending on your CMA version: ■ Sun Fire X4500/X4540 Installation Guide ■ Sun X4500-J Slide Rail Installation Guide (X4500) ■ "Early-Production Slide Rail and CMA Information" ...
Service Manual - Page 170
... this component. Note - For an updated list of the system: ■ DIMM fault LED:
3-50
Sun Fire X4500/X4540 Server Service Manual • May 2010 DIMM fault LEDs are under the DIMM ejector levers that are functioning properly.
DIMM and CPU fault LEDs on the system controller indicates a problem with either the CPUs or...
Service Manual - Page 179
....com/handbook_pub/Systems/
TABLE 3-15 Sun Fire X4500 Supported GRASP Board Part Numbers
Component
Part Number
Graphics Service Processor (GRASP) board, includes SP board and #...part numbers for this LED is a power status LED (CR1) on page G-1 (X4500)
3.
For an updated list of the following: ■ Sun Fire X4500/X4540 Installation Guide ■ Sun X4500-J Slide Rail Installation Guide...
Service Manual - Page 180
... left, and with the bottom connectors on page 3-68.
7. See "Replacing the System Controller (FRU)" on the I/O board. Replace the cable management assembly if necessary: ■ Sun Fire X4500/X4540 Installation Guide ■ Sun X4500-J Slide Rail Installation Guide (X4500)
3-60
Sun Fire X4500/X4540 Server Service Manual • May 2010 FIGURE 3-28 Removing the GRASP Board (X4500...
Service Manual - Page 184
... component. To remove a DIMM:
a. There are subject to remove it from the socket.
▼ To Install Memory Modules (DIMMs) (CRU)
TABLE 3-18 lists the qualified part numbers for the X4540.
3-64
Sun Fire X4500/X4540 Server Service Manual • May 2010 6. Rotate both DIMM slot ejectors outward as far as they will go. Carefully...
Service Manual - Page 186
... and must be replaced only by operating systems are listed on page G-1 (X4500)
3. Option cards supported by qualified service technicians. To check if the driver of your Sun Service representative for download, check the Option Cards link on your CMA version: ■ Sun Fire X4500/X4540 Installation Guide
3-66
Sun Fire X4500/X4540 Server Service Manual • May 2010...
Service Manual - Page 187
...updated list of the following web site:
http://sunsolve.sun.com/handbook_pub/Systems/
TABLE 3-19 Sun Fire X4500/X4540 Supported System Enclosure Part Numbers
Component
Part... 3-19 lists the qualified part numbers for assistance.
This component is a FRU and must be installed only by qualified service technicians. ■ Sun X4500-J Slide Rail Installation Guide (X4500) ■ "Early...
Service Manual - Page 188
... will know where to the equivalent bay in the new chassis. Install the new chassis into the new chassis. 12. A replacement system controller does not include the CPU, memory (DIMMs), GRASP board (X4500) or Service Processor (X4540), or PCI cards. See "To Replace a Fan Module (CRU)" on page 3-43.
5. Use an adhesive note or...
Service Manual - Page 189
... controller, remove them from the old system controller:
a. See "To Replace a CPU (FRU)" on page 3-58. For an updated list of the following web site:
http://sunsolve.sun.com/handbook_pub/Systems/
TABLE 3-20 Sun Fire X4540 Supported System Controller Part Numbers
Component
System Controller Upgrade Kit (includes I/O controller board (USB) and CPU board, 2x2356, 16x2GB...
Service Manual - Page 190
...Section 3.6, "Servicetool FRU Update Procedure" on page 3-8.
▼ To Remove the System Controller (CRU)
The system controller consists of the following docs depending on your CMA version: ■ Sun Fire X4500/X4540 Installation Guide ■ Sun X4500-J Slide Rail Installation Guide (X4500) ■... system controller handle.
3-70
Sun Fire X4500/X4540 Server Service Manual • May 2010
Service Manual - Page 208
... end-POST, just before giving control to runtime code booting to OS.
Initialize the CPUs before booting to OS. Programmed the system BIOS (0F0000h shadow RAM) cacheability. Copy OEM-specific data from each node. B-10 Sun Fire X4500/X4540 Server Service Manual • May 2010 Execute BIOS setup if needed/requested.
Clean-up based on...
Xerox 4540 Reviews
We have not received any reviews for Xerox yet.