English Manual
Page 1
If you have questions, or if there are missing parts, we are committed to providing complete customer satisfaction. Serial Number Decal (Under Seat) QUESTIONS? Save this equipment. The technicians on our customer hot line will ...
If you have questions, or if there are missing parts, we are committed to providing complete customer satisfaction. Serial Number Decal (Under Seat) QUESTIONS? Save this equipment. The technicians on our customer hot line will ...
English Manual
Page 2
TABLE OF CONTENTS IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 4 ASSEMBLY 5 ADJUSTMENTS 21 WEIGHT RESISTANCE CHART 23 TROUBLESHOOTING 24 CABLE DIAGRAMS 25 ORDERING REPLACEMENT PARTS Back Cover LIMITED WARRANTY Back Cover Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of ICON Health & Fitness, Inc. 2 Remove the PART IDENTIFICATION CHART and the PART LIST/EXPLODED DRAWING before beginning assembly. WEIDER is a registered trademark of this manual.
TABLE OF CONTENTS IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 4 ASSEMBLY 5 ADJUSTMENTS 21 WEIGHT RESISTANCE CHART 23 TROUBLESHOOTING 24 CABLE DIAGRAMS 25 ORDERING REPLACEMENT PARTS Back Cover LIMITED WARRANTY Back Cover Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of ICON Health & Fitness, Inc. 2 Remove the PART IDENTIFICATION CHART and the PART LIST/EXPLODED DRAWING before beginning assembly. WEIDER is a registered trademark of this manual.
English Manual
Page 3
...users of the weight system are raised. Mountain Time, to protect the floor. 5. Apply the decal in the literature. 2. Read all parts are exercising, stop immediately and begin cooling down. 14. It is intended for persons over the age of 35 or persons with great force... location shown on all times. 7. The weights will fall with pre-existing health problems. Read all times. Always disconnect the lat bar from moving parts. 8. until 6 p.m. WARNING: Before beginning this product. 3 Keep hands and feet away from the weight system when performing an exercise that the ...
...users of the weight system are raised. Mountain Time, to protect the floor. 5. Apply the decal in the literature. 2. Read all parts are exercising, stop immediately and begin cooling down. 14. It is intended for persons over the age of 35 or persons with great force... location shown on all times. 7. The weights will fall with pre-existing health problems. Read all times. Always disconnect the lat bar from moving parts. 8. until 6 p.m. WARNING: Before beginning this product. 3 Keep hands and feet away from the weight system when performing an exercise that the ...
English Manual
Page 4
...tone your body, build dramatic muscle size and strength, or improve your benefit, read this manual). If you for selecting the versatile WEIDER® PRO 3770 weight system. Width: 86.5 in . WARNING DECAL Butterfly Arms Backrests Seat Curl Pad Leg Lever Low Pulley Station Foot Plate 4... Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled. The serial number can be found on...
...tone your body, build dramatic muscle size and strength, or improve your benefit, read this manual). If you for selecting the versatile WEIDER® PRO 3770 weight system. Width: 86.5 in . WARNING DECAL Butterfly Arms Backrests Seat Curl Pad Leg Lever Low Pulley Station Foot Plate 4... Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled. The serial number can be found on...
English Manual
Page 5
... toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. How to read the information on the floor and use it takes to Orient Parts As you have the following tools: • Two (2) adjustable wrenches • One (1) standard screwdriver • One (1) phillips screwdriver • ...One (1) rubber mallet • You will require about six hours. Tightening Parts Tighten all parts of its weight and size, the weight system should be assembled in the location where it will be more time than it to the...
... toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. How to read the information on the floor and use it takes to Orient Parts As you have the following tools: • Two (2) adjustable wrenches • One (1) standard screwdriver • One (1) phillips screwdriver • ...One (1) rubber mallet • You will require about six hours. Tightening Parts Tighten all parts of its weight and size, the weight system should be assembled in the location where it will be more time than it to the...
English Manual
Page 6
.... 52 50 4 92 3 U-Bracket 50 6 Make sure the Plastic Bushing (52) is on the Butterfly Base (4) with two 3/8" Nylon Locknuts (50). Locate and open the parts bags labeled "FRAME ASSEMBLY." Insert two 1 1/2" x 2 1/2" Inner Caps (83) into the indicated ends of the information on the Press Base (6) with two 3/8" Nylon Locknuts (50...
.... 52 50 4 92 3 U-Bracket 50 6 Make sure the Plastic Bushing (52) is on the Butterfly Base (4) with two 3/8" Nylon Locknuts (50). Locate and open the parts bags labeled "FRAME ASSEMBLY." Insert two 1 1/2" x 2 1/2" Inner Caps (83) into the indicated ends of the information on the Press Base (6) with two 3/8" Nylon Locknuts (50...
English Manual
Page 9
... Press Top Frame (9) with the Left Pivot Arm (not shown). Press a 1 1/2" Square Inner Cap (35) into the Right Pivot Arm (85). Locate and open the parts bag labeled "ARM ASSEMBLY." Repeat this step with two 3/8" x 3 1/4" Bolts (62), two 3/8" Flat Washers (48), and two 3/8" Nylon Locknuts (50). Secure the Press Top Frame...
... Press Top Frame (9) with the Left Pivot Arm (not shown). Press a 1 1/2" Square Inner Cap (35) into the Right Pivot Arm (85). Locate and open the parts bag labeled "ARM ASSEMBLY." Repeat this step with two 3/8" x 3 1/4" Bolts (62), two 3/8" Flat Washers (48), and two 3/8" Nylon Locknuts (50). Secure the Press Top Frame...
English Manual
Page 11
IMPORTANT: While assembling the cables, do not over a "V"-Pulley (27). Locate and open the parts bags labeled "CABLE ASSEMBLY" and "PULLEYS." Attach the "V"-Pulley and a Large Cable Trap (32) to the Press Front Leg (20) 19 with a 1" Tap Screw (80). ...
IMPORTANT: While assembling the cables, do not over a "V"-Pulley (27). Locate and open the parts bags labeled "CABLE ASSEMBLY" and "PULLEYS." Attach the "V"-Pulley and a Large Cable Trap (32) to the Press Front Leg (20) 19 with a 1" Tap Screw (80). ...
English Manual
Page 19
... with four 1/4" x 3/4" Bolts (49). 35 49 Pull out the Adjustment Knob (5) on the Butterfly Seat Frame (14) using four 1/4" x 3/4" Bolts (49). Locate and open the parts bag labeled "SEAT ASSEMBLY." Attach a Backrest (12) to the Press Leg Lever (90) with the other Backrest (12) to the brackets on the Butterfly Upright...
... with four 1/4" x 3/4" Bolts (49). 35 49 Pull out the Adjustment Knob (5) on the Butterfly Seat Frame (14) using four 1/4" x 3/4" Bolts (49). Locate and open the parts bag labeled "SEAT ASSEMBLY." Attach a Backrest (12) to the Press Leg Lever (90) with the other Backrest (12) to the brackets on the Butterfly Upright...
English Manual
Page 20
... the cables are not properly installed, they may be damaged when heavy weight is any slack in the cables, you will be sure that all parts have been properly tightened. Slide the Pad Tube through the welded tube on page 21 of a Pad Tube (42). Slide a Foam Pad (30) onto one... the Pad Tube. Slide another Foam Pad onto the other side of the Pad Tube. 56. If there is used. If one of the remaining parts will need to the Preacher Post (39) with four 1/4" x 3/4" Bolts (49). Make sure that the cables move smoothly, find and correct the problem. 55. Insert...
... the cables are not properly installed, they may be damaged when heavy weight is any slack in the cables, you will be sure that all parts have been properly tightened. Slide the Pad Tube through the welded tube on page 21 of a Pad Tube (42). Slide a Foam Pad (30) onto one... the Pad Tube. Slide another Foam Pad onto the other side of the Pad Tube. 56. If there is used. If one of the remaining parts will need to the Preacher Post (39) with four 1/4" x 3/4" Bolts (49). Make sure that the cables move smoothly, find and correct the problem. 55. Insert...
English Manual
Page 21
..., make sure that the attachments are in the cables or chain as an exercise is touching the Weights. ADJUSTMENTS The instructions below describe how each part of the weight system can be changed from the weight setting. CHANGING THE WEIGHT SETTING To change the weight setting of the weight stack, insert...
..., make sure that the attachments are in the cables or chain as an exercise is touching the Weights. ADJUSTMENTS The instructions below describe how each part of the weight system can be changed from the weight setting. CHANGING THE WEIGHT SETTING To change the weight setting of the weight stack, insert...
English Manual
Page 24
... Pulley Plates with the 3/8" x 2" Bolt and 3/8" Nylon Locknut. Remove the cable and re-install it may have become twisted. Replace any worn parts immediately. TIGHTENING THE CABLES Woven cable, the type of cable used on the weight system, can be cleaned using a damp cloth and mild non-abrasive...Remove the 3 1/2" Pulley (24) and the Cable Trap (25). If the cables are over tightened, the top weight will be replaced, see ORDERING REPLACEMENT PARTS on the Weight 1 Cable (72) bolt, away from the Adjustable Pulley Plates (23). If the cables need to slip off the weight stack. Do ...
... Pulley Plates with the 3/8" x 2" Bolt and 3/8" Nylon Locknut. Remove the cable and re-install it may have become twisted. Replace any worn parts immediately. TIGHTENING THE CABLES Woven cable, the type of cable used on the weight system, can be cleaned using a damp cloth and mild non-abrasive...Remove the 3 1/2" Pulley (24) and the Cable Trap (25). If the cables are over tightened, the top weight will be replaced, see ORDERING REPLACEMENT PARTS on the Weight 1 Cable (72) bolt, away from the Adjustable Pulley Plates (23). If the cables need to slip off the weight stack. Do ...
English Manual
Page 29
PART IDENTIFICATION CHART-Model No. WESY37531 R1003A 1/2" Flat Washer (11) 3/8" Flat Washer (48) Cable Clip (69) 1/2" Plain Nut (45) 1/2" Nylon Jamnut (36) 3/8" Nylon Locknut (50) 5/16" Nylon Locknut (64) 1/2" x 3/4" Spacer (97) 3/8" Nylon Jamnut (63) 5/16" Nylon Jamnut (34) 5/8" x 3/4" Bushing (66) 5/8" x 1/2" Spacer (93) 4 1/2" Pulley (82) (Not shown to scale) "V" Pulley (27) (Not shown to scale) 3 1/2" Pulley (24) (Not shown to scale) Retainer Ring (31) 3/4" Round Inner Cap (43) 1" Round Inner Cap (86) 1" Round Outer Cap (38)
PART IDENTIFICATION CHART-Model No. WESY37531 R1003A 1/2" Flat Washer (11) 3/8" Flat Washer (48) Cable Clip (69) 1/2" Plain Nut (45) 1/2" Nylon Jamnut (36) 3/8" Nylon Locknut (50) 5/16" Nylon Locknut (64) 1/2" x 3/4" Spacer (97) 3/8" Nylon Jamnut (63) 5/16" Nylon Jamnut (34) 5/8" x 3/4" Bushing (66) 5/8" x 1/2" Spacer (93) 4 1/2" Pulley (82) (Not shown to scale) "V" Pulley (27) (Not shown to scale) 3 1/2" Pulley (24) (Not shown to scale) Retainer Ring (31) 3/4" Round Inner Cap (43) 1" Round Inner Cap (86) 1" Round Outer Cap (38)
English Manual
Page 31
... 2 5/8" x 1/2" Spacer 94 2 Support Plate 95 1 Plastic Weight Cover 96 4 5/16" x 2 3/4" Bolt 97 1 1/2" x 3/4" Spacer 98 1 3/8" x 1 1/2" Button Head Bolt # 1 User's Manual # 1 Exercise Guide Note: "#" indicates a non-illustrated part. WESY37531 R1003A Key No. Qty...
... 2 5/8" x 1/2" Spacer 94 2 Support Plate 95 1 Plastic Weight Cover 96 4 5/16" x 2 3/4" Bolt 97 1 1/2" x 3/4" Spacer 98 1 3/8" x 1 1/2" Button Head Bolt # 1 User's Manual # 1 Exercise Guide Note: "#" indicates a non-illustrated part. WESY37531 R1003A Key No. Qty...
English Manual
Page 33
...product (WESY37531) • The NAME of the product (WEIDER® PRO 3770 weight system) • The SERIAL NUMBER of the product (see the front cover of this manual) • The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING attached at 1-800-999-3756, ... claim is not responsible or liable for a period of ninety (90) days from the date of purchase. until 6 p.m. ORDERING REPLACEMENT PARTS To order replacement parts, simply call our Customer Service Department toll-free at the center of this manual) LIMITED WARRANTY ICON Health & Fitness, Inc. (ICON),...
...product (WESY37531) • The NAME of the product (WEIDER® PRO 3770 weight system) • The SERIAL NUMBER of the product (see the front cover of this manual) • The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING attached at 1-800-999-3756, ... claim is not responsible or liable for a period of ninety (90) days from the date of purchase. until 6 p.m. ORDERING REPLACEMENT PARTS To order replacement parts, simply call our Customer Service Department toll-free at the center of this manual) LIMITED WARRANTY ICON Health & Fitness, Inc. (ICON),...