Weider Pro 9835 Support and Manuals
Get Help and Manuals for this Weider item
View All Support Options Below
Free Weider Pro 9835 manuals!
Problems with Weider Pro 9835?
Ask a Question
Free Weider Pro 9835 manuals!
Problems with Weider Pro 9835?
Ask a Question
Most Recent Weider Pro 9835 Questions
I Need The Leg Press Cable
wcablewhat is the part number for the leg press cable on the 9835 model?
wcablewhat is the part number for the leg press cable on the 9835 model?
(Posted by sehongang 5 years ago)
How Do You Keep Maintenance On The Welder Pro 9835?
(Posted by francismarcell4 10 years ago)
Popular Weider Pro 9835 Manual Pages
English Manual - Page 1
...;Fri., 6 a.m.Ð6 p.m. WESY41080 Serial No.
USERÕS MANUAL
PATENT PENDING
Save this equipment. Model No.
TO AVOID UNNECESSARY DELAYS, PLEASE CALL DIRECT TO OUR TOLL-FREE CUSTOMER HOT LINE. Write the serial number in this manual before using this manual for future reference. MST
CAUTION
Read all precautions and instructions in the space above for future...
English Manual - Page 2
...feet away from the home
surface. Inspect and tighten all instructions before using .
Table of Contents
Important Precautions 2 Before You Begin 3 Assembly 4 How to Use the Home Gym System 23 Trouble-shooting and Maintenance 25 Cable Diagrams 26 Weight Resistance Chart 27 Ordering Replacement Parts Back Cover Limited Warranty Back Cover
Note: A PART LIST/EXPLODED DRAWING and...
English Manual - Page 3
... group of this manual carefully before calling. Width: 64 in . To help you to achieve the specific results you , please note the product model number and serial number before using the WEIDER PRO¨ 9835 Home Gym System.
Length: 70 in .
Backrests
Butterfly Arms VKR Station
Press Arm
Leg Lever
Low Pulley Station
Foot Plate
Weight Stacks
3
Leg Press...
English Manual - Page 4
... over a couple of evenings. Most people find that by setting aside plenty of the equipment. Tightening of Parts
Tighten all parts as you assemble them, unless instructed to make sure all parts in each assembly stage to quickly identify different parts as the skeleton of time, and by assembling the base and the upright frames that you operate while...
English Manual - Page 8
...
23
8 Attach the Butterfly Frame (3) to the Top Frame (2) with two 5/16Ó x 2 3/4Ó Bolts (55), the Support Plate (98) and two 5/16Ó Nylon Locknuts (40). Attach the upper ends of one set of Weight Guides (23).
24 Lubricate
23
24
Lubricate
23
8.
Before continuing, firmly tighten all nylon locknuts used in the...
English Manual - Page 9
...to the Front Seat Frame (8) with the 1Ó Tap Screw (72). Locate and open the parts bag labeled ÒARM ASSEMBLY.Ó
Attach the Leg Press Bumper (53) to the Press Base (13) with the Bolt... (13) so that the Plastic Bushings are aligned with the upper set of the 10 Leg Press Arm (9).
56 A 56
9
56
56
Arm Assembly
11
11.
Make sure the Press Frame is oriented with the indicated...
English Manual - Page 11
...of the Left
Arm with the Right Arm (5).
5
Note: The remaining parts from the parts bag labeled ÒARM ASSEMBLYÓ will be able to verify proper cable routing. The approximate length ...; x 1Ó Bolt (95). Before beginning this manual to turn freely.
18. 16. Locate and open the parts bags labeled ÒCABLE ASSEMBLYÓ and ÒPULLEYS.Ó
During steps 18 through...
English Manual - Page 12
... (82) as shown. The
Cable Trap must be oriented as shown and be
down
21. Locate one of the pre-assembled pairs of the Butterfly Cable (89) onto the
5/16Ó x 1Ó Bolt (95). Tighten the 3/8Ó ... the Cable in place. 19. Make sure the Cable is between the two Jam Nuts for easier part identification. Fully tighten a
91
5/16Ó Nylon Jam Nut (91) onto the Bolt.
89
...
English Manual - Page 20
...
48. Locate and open the parts bag labeled ÒSEAT ASSEMBLY.Ó
Attach a Small Backrest (97) to the Rear Seat Frame (16) with two 1/4Ó x 2 1/2Ó Machine Screws (64) and two 1/4Ó Washers (37...17) to the Lat Upright (1) with a 1/4Ó Washer (37) and a 1/4Ó x 2Ó Machine Screw (63).
16 44
17
59
37
63
50.
Lubricate the 5/16Ó x 2 1/4Ó Bolt...
English Manual - Page 22
..., you will be sure that the cables move smoothly, find and correct the problem.
See TROUBLE-SHOOTING AND MAINTENANCE on one of this manual for proper cable routing. A
3 1/2Ó 5 3/4Ó
73 11 Welded Tubes
59. 56. Note that all parts have been properly tightened. If one side the distance from the square hole to...
English Manual - Page 23
....
Refer to the exercise poster accompanying this manual to see how the home gym system should be attached in increments of either weight stack can be per-
36
formed.
Adjust... Home Gym System
The instructions below describe how each part of the home gym system can be set up for each exercise. For some exercises, the Chain (34)
should be adjusted. The other weight stack...
English Manual - Page 25
... weight stack. tightened, the top weight will need to the Large ÒUÓ Bracket (84).
¥ See drawing 1. The home gym system can be lifted off the pulleys often, it is slack in the Large ÒUÓ Bracket.
Trouble-shooting and Maintenance
Inspect and tighten all parts each time you feel additional slack while using
the home gym...
English Manual - Page 26
... have been labeled. Use the diagrams to be sure that the Cables have not been correctly routed, the home gym system will not function properly and damage may occur. Press Cable (88)
Low Cable (86)
2 ...4
5ÑLeft Arm
2
1ÑRight Arm
3
26
IMPORTANT: If the Cables have been assembled correctly. The numbers show the proper routing of each Cable. The starting and ending points of ...
English Manual - Page 29
... Nut
92
3
5/16Ó x 3Ó Bolt
93
2
Weight Pin
94
3
3/8Ó x 3Ó Bolt
95
3
5/16Ó x 1Ó Bolt
96
1
Handle
97
1
Small Backrest
98
1
Support Plate
#
1
UserÕs Manual
#
1
Exercise Poster
Note: Ò#Ó indicates a non-illustrated part. Part List - Qty. Model No. WESY41080
R0898A
Key No. Specifications are subject to change without notice...
English Manual - Page 33
The MODEL NUMBER of the product (WEIDER PRO¨ 9835 Home Gym System).
3. Accordingly, the above limitation may not apply to you specific legal rights.
This warranty gives you . ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 147764 H01818-C R0898A
Printed in workmanship and material, under this warranty is limited to replacing or repairing, at ICON's ...
Weider Pro 9835 Reviews
We have not received any reviews for Weider yet.