Weider Pro 9835 Support Question
Find answers below for this question about Weider Pro 9835.Need a Weider Pro 9835 manual? We have 1 online manual for this item!
Question posted by sehongang on August 5th, 2018
I Need The Leg Press Cable
wcablewhat is the part number for the leg press cable on the 9835 model?
Current Answers
There are currently no answers that have been posted for this question.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Related Weider Pro 9835 Manual Pages
English Manual - Page 2
... cannot slide out (see page 24).
15. Replace any time while exercising, stop immediately and make sure the lock pin is in the accompanying literature before using the leg press station, always make sure the cables are on a foot plate when performing an exercise that could cause the home gym system to tip.
13. When...
English Manual - Page 3
... WEIDER PRO¨ 9835 Home Gym System. Backrests
Butterfly Arms VKR Station
Press Arm
Leg Lever
Low Pulley Station
Foot Plate
Weight Stacks
3
Leg Press Plate The serial number can be...read this manual). The model number is to achieve the specific results you , please note the product model number and serial number before using the WEIDER PRO¨ 9835 Home Gym System. Mountain ...
English Manual - Page 4
...; Tape, such as the skeleton of the equipment.
Cable Assembly
Completes the cables and pulleys that you operate while you are found in... of the packing materials until you begin each stage are exercising. The Four Stages of the Assembly Process
Frame Assembly
You... are oriented as a unit
Arm Assembly
Completes the press and butterfly arms that connect the moving parts will ...
English Manual - Page 5
...Base (14).
Before beginning assembly, make sure you have read and understand the information in the Press Base (13).
Press a 2Ó Square Inner Cap (56) into the indicated end of the Weight Base (14...
40
40 49
40 49
13
Frame Assembly
1. Attach the Press Base (13) to the Weight Base. Slide the Leg Press Upright (4) onto the indicated 5/16Ó x 2 1/2Ó Carriage Bolts (49...
English Manual - Page 6
... (2). Slide the Front Seat Frame (8) onto the indicated 5/16Ó x 2 1/2Ó Carriage Bolts (49) in the Press Base
4
(13).
Tighten a 5/16Ó Nylon Jam Nut (91) with two 5/16Ó x 2 3/4Ó Bolts... that the Bolt is on the side shown. Press a 2Ó Square Inner Cap (56) into the end of the Front Seat Frame (8) to the Leg Press Upright (4) with a 5/16Ó Washer (20)...
English Manual - Page 8
...211; x 2 3/4Ó Bolts (55), two 5/16Ó Washers (20) and two 5/16Ó Nylon Locknuts (40). Press a 2Ó Square Inner Cap (56) into the top end of the holes in steps 1 through 9.
9
40 2
40... the VKR Upright.
8 2
55 20
55
56
98
55
40 20
3
Attach the VKR Upright (51) to the Leg Press Upright (4) with two 5/16Ó x 2 3/4Ó Bolts (55), two 5/16Ó Washers (20) and two...
English Manual - Page 9
... Nylon Jamnut, it should be a tight fit. Slide the Press Frame onto the Press Base (13) so that the Plastic Bushings are aligned with the Bolt and a 3/8Ó Nylon Jamnut (43). Attach the Press Frame (12) to pivot the Leg Press Arm.
8 9
53 72
13
43 94ÑLubricate
12. Press a 2Ó Square Inner Cap (56) into...
English Manual - Page 12
... bracket on the Left Arm. Refer to hold the Cable in place. Leave enough room between the Cable Trap (80) and the Pulley, and that the Cable Trap is shown removed for
95
6
the Cable to hold the Cable in the groove of the bracket on the Leg Press
Upright (4) with
two holes
31
should be downward...
English Manual - Page 14
... in
the inset drawing.
37
84
44
37
88
88
84
28. Attach the Pulley and a Cable Trap (80) to hold the Cable in
place.
50
13
88 82
80 42
50 13
14 Find the Press Cable (88)Ñthis is turned to the
Large ÒUÓ Bracket (84) with a 3/8Ó x
2Ó Bolt...
English Manual - Page 15
...). Tighten the 3/8Ó x 2Ó Bolt (50) and the 3/8Ó Nylon Locknut (42, not shown).
31 50 82
80 88
31. Attach the Pulley and a Cable Trap (80) to the
31
Leg Press Upright (4) with a 3/8Ó x 3Ó Bolt (94), a 3/8Ó Washer (38) and a 3/8Ó Nylon Jamnut (43).
Refer to the upper bracket on the...
English Manual - Page 16
....
Attach the ÒVÓ Pulley and a Large Cable Trap (83) to
37
the bracket on the Leg
35
Press Upright (4) with a 3/8Ó x
2 1/2Ó Bolt (65) and a 3/8Ó Nylon Locknut (42). Be
sure that the Large Cable Trap is turned to hold the Cable in place and that the Cable is turned to the lower bracket on...
English Manual - Page 17
... a 5/16Ó Nylon Jam Nut (91) onto the Bolt.
Wrap the High Cable around the 3 1/2Ó Pulley (82). Be sure that the Cable is on the indicated side of the Press Cable (88) onto the Bolt. It is the longest remaining cable. Route the Press Cable (88) around a 3 1/2Ó Pulley (82). Slide the end of the Pulley...
English Manual - Page 21
...x 2 1/2Ó Carriage Bolt (60) through the
54
center hole in the 55 VKR arms located underneath the handles.
57
Press a 1 1/2Ó Square inner Cap (57) into the holes in a Seat Plate (41). Attach a VKR Armrest (71... end of the Pad Tube.
15
16
28 29 78
53. Attach the Seat Plate
to the Leg Press Upright 53 (4) with a 1/4Ó Washer (37) onto the Carriage Bolt. Attach the other end...
English Manual - Page 22
...page 26 and 27 of the remaining parts will need to be explained in the cables, you will be sure that all parts have ...Leg Press Arm (9). Slide the Leg Press Plate (11) onto the end of the holes in the adjustment tube (A).
57 9
Make sure the Leg Press Plate is any slack in HOW TO USE THE HOME GYM SYSTEM, beginning on the Leg Press Plate (11) and one of this manual for proper cable...
English Manual - Page 23
... (96) can be attached between the Lat Bar and the High Cable so the
Lat Bar is connected to the
butterfly and press arms and the leg press. 93
To change the weight setting of either weight stack can be reduced. For some exercises, the Chain (34) should be attached in the correct starting position...
English Manual - Page 24
...of the Chain to the leg lever. A
Holes
73
9
Welded Tubes 11
24 ATTACHING AND REMOVING THE SEAT
To attach the Seat (17), set of holes in the adjustment tube. For some exercises, the Seat (17) must...THE SEAT above).
Attach one end of the Chain (34) to the Low Cable (86) with a Cable Clip.
15 79
33
34 86
ADJUSTING THE LEG PRESS PLATE
Remove the Lock Pin (73) from the Rear Seat Frame (16)....
English Manual - Page 25
... (42), the 3 1/3Ó Pulleys (82), and the Cable
Traps (80) from the Cable Trap (80), Pulley, and Large ÒUÓ Bracket (84).
TIGHTENING THE CABLES
Woven cable, the type of the Press Cable (88) to the other weight stack, the Rear Cable (87), the Press Cable (88), and the Butterfly Cable (89) will need to be tightened. Tighten the 1/4Ó Nylon...
English Manual - Page 26
Press Cable (88)
Low Cable (86)
2 1ÑLong ÒUÓ Bracket
1
4
5
2 3 9
7
Leg PressÑ13 6
11
8 12
10
3ÑLow Pulley
Butterfly Cable (89)
4
5ÑLeft Arm
2
1ÑRight Arm
3
26
The numbers show the proper routing of each Cable. The starting and ending points of the High Cable (85), the Low Cable (86), the Rear Cable (87), the Press Cable (88), and the...
English Manual - Page 27
...refers to the 6.5 lbs. The other numbers refer to differences in individual weight plates, as well as friction between the cables, pulleys, and weight guides. top weight.
WEIGHT PLATES
Top 1 2 3 4 5 6 7 8
PRESS ARM (lbs.)
27 53 79 101 ...66 80 96 107
123
LOW PULLEY
(lbs.)
10 24 41 53 63 80 91 101
120
LEG PRESS (lbs.)
52 94 141 180 228 263 310 358
410
27 weight plates. Note: The actual...
English Manual - Page 29
...; Bracket
85
1
High Cable
86
1
Low Cable
87
1
Rear Cable
88
1
Press Cable
89
1
Butterfly Cable
90
16
Weight
91
8
5/16Ó Nylon Jam Nut
92
3
5/16Ó x 3Ó Bolt
93
2
Weight Pin
94
3
3/8Ó x 3Ó Bolt
95
3
5/16Ó x 1Ó Bolt
96
1
Handle
97
1
Small Backrest
98
1
Support Plate
#
1
UserÕs Manual
#
1
Exercise Poster
Note: Ò...
Similar Questions
I Need A Butterfly Cable For My Weider Club 4870. Can You Help Me?
(Posted by longshotbooks 1 month ago)
I Need A Replacement Cable For My Welder Pro 8900 Do You Guys Carry One?
(Posted by mjdunkin21 3 years ago)
All Cable Cut Need Diagram Of Cable Formation And Linkage
Cable replacement
Cable replacement
(Posted by vernonchaney69 6 years ago)
I Need To Replace Cable For Chest And Leg Station. Both Use The Same Cable.
(Posted by vnvpirate 9 years ago)
How Do You Keep Maintenance On The Welder Pro 9835?
(Posted by francismarcell4 10 years ago)