LC-M3700 Operation Manual
Page 4
... the cabinet are followed. 11. Keep this manual in accidents. 7. ments can break when the product is made of a SHARP LCD product. Therefore, it can result in a safe place-These safety and operating instructions must be read the Safety Precautions carefully.... 3. For the same reason, do not spill water or liquid on an unstable cart, stand, tripod or table. Introduction Connection and Installation Basic Operation PC Operation DEAR SHARP CUSTOMER Thank you to perform servicing. 3 US Settings and Adjustments Troubleshooting and Specifications Appendix To...
... the cabinet are followed. 11. Keep this manual in accidents. 7. ments can break when the product is made of a SHARP LCD product. Therefore, it can result in a safe place-These safety and operating instructions must be read the Safety Precautions carefully.... 3. For the same reason, do not spill water or liquid on an unstable cart, stand, tripod or table. Introduction Connection and Installation Basic Operation PC Operation DEAR SHARP CUSTOMER Thank you to perform servicing. 3 US Settings and Adjustments Troubleshooting and Specifications Appendix To...
LC-M3700 Operation Manual
Page 13
... for temporary use a special-purpose AN-37ST1 table stand or AN-37AG1 wallmount bracket (both optional). 23 Mounting Options. Be sure to use only until the monitor is equipped with the product. Remote control ... washer (× 2) (XWHS960-16180) (XBBS960P20000) Page 29 Caution: » This monitor is properly mounted. Supplied Accessories Make sure the following accessories are provided with a temporary stand when shipped from the factory.
... for temporary use a special-purpose AN-37ST1 table stand or AN-37AG1 wallmount bracket (both optional). 23 Mounting Options. Be sure to use only until the monitor is equipped with the product. Remote control ... washer (× 2) (XWHS960-16180) (XBBS960P20000) Page 29 Caution: » This monitor is properly mounted. Supplied Accessories Make sure the following accessories are provided with a temporary stand when shipped from the factory.
LC-M3700 Operation Manual
Page 24
... the monitor near the edge of the stand hinge. M5 screws 12 mm length (4 screws) Table stand 2. GPlace the monitor (face down) on a table, etc. Assemble the table stand. Mounting the table stand (AN-37ST1) (LC-M3700) See the table stand instructions for LCD panel protection. Please note... this product. G Align the 5 screw holes of the stand base with a temporary stand when shipped from the factory. Rotating range: up...
... the monitor near the edge of the stand hinge. M5 screws 12 mm length (4 screws) Table stand 2. GPlace the monitor (face down) on a table, etc. Assemble the table stand. Mounting the table stand (AN-37ST1) (LC-M3700) See the table stand instructions for LCD panel protection. Please note... this product. G Align the 5 screw holes of the stand base with a temporary stand when shipped from the factory. Rotating range: up...
LC-M3700 Operation Manual
Page 26
...-mount bracket Angle setup bracket (2 units) Attaching wall-mount bracket to the monitor Screws Terminal cover (4 locations) Wide LCD Monitor Temporary stand Table 1. GPlace the monitor (face down) on a table, etc. GPosition the monitor near the edge of the table so that the ...spacers are used to secure the temporary stand in Step 1 (M6 15 mm length × 2 screws) and the included screws M6 15 mm length × 2 screws to loosely fasten the angle-setup bracket with 4 screws. Installation angle: LC-M3700 (Horizontal mount) 0° to 20° LC-M3710 (Vertical mount) 0° ...
...-mount bracket Angle setup bracket (2 units) Attaching wall-mount bracket to the monitor Screws Terminal cover (4 locations) Wide LCD Monitor Temporary stand Table 1. GPlace the monitor (face down) on a table, etc. GPosition the monitor near the edge of the table so that the ...spacers are used to secure the temporary stand in Step 1 (M6 15 mm length × 2 screws) and the included screws M6 15 mm length × 2 screws to loosely fasten the angle-setup bracket with 4 screws. Installation angle: LC-M3700 (Horizontal mount) 0° to 20° LC-M3710 (Vertical mount) 0° ...
LC-M3700 Operation Manual
Page 28
Connection and Installation Outside dimensional drawings »With table stand attached 35-25/32 [909] 31-57/64 [810] Mounting Options (Continued) Unit: inch [mm] 3-29/32 3-15/64 [99.5] [82.1] 2-5/16 [58.8] 11-13/...
Connection and Installation Outside dimensional drawings »With table stand attached 35-25/32 [909] 31-57/64 [810] Mounting Options (Continued) Unit: inch [mm] 3-29/32 3-15/64 [99.5] [82.1] 2-5/16 [58.8] 11-13/...
LC-M3700 Operation Manual
Page 68
...individual units. The performance specification figures indicated are available for product improvement without prior notice. Specifications Product Model Wide LCD Monitor LC-M3700/LC-M3710 LCD Screen size inch (mm) Panel Drive Number of dots Color system Speaker Audio amplifier Terminals Power requirement Power ... 181 W 0.8 W 37-23/64 x 3-29/32 x 22-33/64 (949 x 99.5 x 572) 41.9 (19) (without stand) 0°C - +40°C 20% - +80% I As a part of policy of continuous improvement, SHARP reserves the right to rely on the screen as a fixed point of blue, green or red.
...individual units. The performance specification figures indicated are available for product improvement without prior notice. Specifications Product Model Wide LCD Monitor LC-M3700/LC-M3710 LCD Screen size inch (mm) Panel Drive Number of dots Color system Speaker Audio amplifier Terminals Power requirement Power ... 181 W 0.8 W 37-23/64 x 3-29/32 x 22-33/64 (949 x 99.5 x 572) 41.9 (19) (without stand) 0°C - +40°C 20% - +80% I As a part of policy of continuous improvement, SHARP reserves the right to rely on the screen as a fixed point of blue, green or red.