Seagate ST336706LW - Cheetah 36.7 GB Hard Drive Support and Manuals
Get Help and Manuals for this Seagate item
View All Support Options Below
Free Seagate ST336706LW manuals!
Problems with Seagate ST336706LW?
Ask a Question
Free Seagate ST336706LW manuals!
Problems with Seagate ST336706LW?
Ask a Question
Popular Seagate ST336706LW Manual Pages
Product Manual - Page 5
... Product Manual, Rev. commands 30 B
FCC verification 15
Configuring and mounting the drive 17 Handling and static-discharge precautions 17 Jumper settings 18 Master/slave configuration 18 Cable-select option 19 Ultra ATA/66 cable 19 Drive mounting 19
ATA interface 21 ATA interface signals and connector pins 21 Supported ATA commands 23 Identify Drive command 24 Set Features...
Product Manual - Page 6
U8 Family Product Manual, Rev. B
v
Figures
Typical startup and operation current profile 9 Master/slave jumper settings 18 Mounting dimensions-top, side and end view 20 I/O pins and supported ATA signals 22
Product Manual - Page 8
...cable select
(CSEL)
• SeaShield® innovative, shock-absorbing cover shields the drive
against electrostatic discharge (ESD) and other handling damage. B
1
Introduction
This manual describes the functional, mechanical and interface specifications for the ST317221A, ST313021A, ST38410A and the ST34313A. It also includes installation instructions and jumper settings. U8 Family Product...
Product Manual - Page 9
... (Mbits/inch2 max)
6,536
Spindle speed (RPM)
5,400
Internal data-transfer rate (Mbits/ sec max)
285.5
I/O data-transfer rate (Mbytes/ sec max)
66.6
ATA data-transfer modes supported
PIO modes 0-4 Multiword DMA modes 0-2
Ultra DMA modes 0-4
Cache buffer (Kbytes)
512 256-Kbyte cache is optional for quick reference. Drive Specification
ST317221A ST313021A ST38410A ST34313A
Guaranteed...
Product Manual - Page 11
B
Drive Specification Nonrecoverable read errors
ST317221A ST313021A ST38410A ST34313A 1 per 1013 bits read
Mean time between failures (power-on hours)
500,000
Contact start-stop cycles (25°C, 40% relative humidity)
50,000
SeaShield
Yes 4
U8 Family Product Manual, Rev.
Product Manual - Page 17
...
U8 Family Product Manual, Rev. In most systems, you can also enter Standby mode automatically after the drive has been inactive for a specifiable length of 100 mV peak-to-peak square-wave injected noise at up to provide greater energy efficiency.
If the host has set the standby timer, the drive can control power...
Product Manual - Page 21
14
U8 Family Product Manual, Rev.
Drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections of IEC950 and EN 60950 as tested by TUV North America.
1.12.2 Electromagnetic compatibility
Hard drives that display the CE marking comply with the EC directives specified in the previous paragraph. Discharges...
Product Manual - Page 24
... or frame only.
• The drive is extremely fragile-handle it protects the drive from the SeaShell. U8 Family Product Manual, Rev. B
17
2.0 Configuring and mounting the drive
This section contains the specifications and instructions for installation.
• The drive is plugged into a grounded outlet. The soft SeaShield cover also includes installation instructions and jumper settings.
Product Manual - Page 26
Refer to your computer manual to determine whether your computer supports this option.
2.2.3 Ultra ATA/66 cable
An 80-conductor 40-pin cable is required to improve signal integrity.
The drive detects the 80-conductor cable by their physical position on the interface bus. To enable cable select, set a jumper on the interface bus. The result is...
Product Manual - Page 28
... ATA-5 Standard. The drive also supports the use the industry-standard ATA task file interface that the drive supports. B
21
3.0 ATA interface
These drives use of the IORDY signal to a single AT host bus. multiword DMA modes 0-2, and Ultra DMA modes 0-4. You can use a daisy-chain cable to connect two drives to provide reliable high-speed data transfers.
Product Manual - Page 30
... Read Verify Sectors Read Native Max Address Recalibrate Seek Set Features Set Multiple Mode Set Max Address S.M.A.R.T. For a detailed description of the ATA commands, refer to the Draft ATA-5 Standard. B
23
3.1.1 Supported ATA commands
The following table lists ATA-standard commands that the drive supports. Command name
Command code (in the S.M.A.R.T. Write Buffer Write DMA
92H 90H...
Product Manual - Page 31
... Unit
F4H
Security Freeze Lock
F5H
Security Disable Password
F6H
3.1.2 Identify Drive command
The Identify Drive command (command code ECH) transfers information about the drive to zero. The data is organized as a single 512-byte block of data, whose contents are drive-specific or vary with the state of this manual for default parameter settings. 24
U8 Family Product...
Product Manual - Page 34
... supported
Command sets supported
Command sets support extension
Command sets enabled
Command sets enabled
Command sets enable extension
Ultra DMA support and current mode (see note following this table)
Security erase time
Enhanced security erase time
27
Value
0078H
0078H
00F0H
0078H 0000H 0000H 0000H 003EH 0000H 346BH 4009H 4000H xxxxH xxxxH xxxxH xx1FH
0000H 0000H U8 Family Product Manual, Rev...
Product Manual - Page 35
...-159 Seagate-reserved
xxxxH
160-254 ATA-reserved
0000H
255 Integrity word
xxA5H
Note. Bit Word 88
0 Ultra DMA mode 0 is supported.
1 Ultra DMA mode 1 is supported.
2 Ultra DMA mode 2 is supported.
3 Ultra DMA mode 3 is currently active. See the bit descriptions below for words, 63, 88 and 93 of the Identify Drive data:
Description (if bit is set to...
Product Manual - Page 36
...Ultra DMA mode 4 is supported. 8 Ultra DMA mode 0 is currently active. 9 Ultra DMA mode 1 is currently active. 10 Ultra DMA mode 2 is currently active. 11 Ultra DMA mode 3 is currently active. 12 Ultra DMA mode 4 is aborted. When the drive receives this command, it sets...defined as follows:
02H
Enable write cache (default).
03H
Set transfer mode (based on default has the read look-ahead ...
Seagate ST336706LW Reviews
We have not received any reviews for Seagate yet.