Sanyo XL50 - PLC XGA LCD Projector Support and Manuals
Get Help and Manuals for this Sanyo item
Most Recent Sanyo XL50 Questions
Xlr301 Sanyo Manual
(Posted by lz0j57 10 years ago)
Sanyo XL50 Videos
Sanyo PLC-XL50 Projector Filter Cleaning Guide
Duration: 2:54
Total Views: 22,949
Duration: 2:54
Total Views: 22,949
Sanyo XL50 Nettoyage filtre
Duration: 9:12
Total Views: 8
Duration: 9:12
Total Views: 8
Popular Sanyo XL50 Manual Pages
Instruction Manual, PLC-XL50 - Page 4
...in the "Troubleshooting" section in not only shortening the product life, but also malfunctions, fire hazard, or other area of the world. CAUTION
Not for an extended time, unplug the projector from the ceiling, clean air intake vents, air filters, or top of the projector periodically with a vacuum cleaner. NO USER-SERVICEABLE PART S I N S I D E E XC E P T LAMP REPLACEMENT. The dimensions...
Instruction Manual, PLC-XL50 - Page 8
...one or more of the following code: Green-and-yellow Earth Blue ...projector meets the requirement for your User Instructions. The wire which is coloured blue must be suitably prepared and the correct plug fitted. THE SOCKET-OUTLET SHOULD BE INSTALLED... of FCC Rules. Model Number(s) Trade Name Responsible party Address Telephone No.
: PLC-XL50 : Sanyo : SANYO FISHER COMPANY : 21605...
Instruction Manual, PLC-XL50 - Page 48
... the pointer. Be sure to relevant instructions of the LOGO pin code no longer be changed without the Logo PIN code. memo on pages 52-53.
If you could no longer change the Logo PIN code. For details on PIN code setting, refer to note the new Logo PIN code and keep it at the factory. Off...
Instruction Manual, PLC-XL50 - Page 60
... be damaged.
5 Reinstall the filter into the air intake vents.
Replacement Filter Part No.: 610 335 4057
RECOMMENDATION We recommend avoiding dusty/smoky environments when you use , a timer setting option, and the reset option. When you operate the projector. When the symptoms above are noticed, contact your dealer for proper cleaning. A dialog box appears showing the total...
Instruction Manual, PLC-XL50 - Page 62
... and unplug the AC power cord. Make sure that secure the lamp.
Close the lamp cover and secure the screw.
5 Connect the AC power cord to avoid damaging it. Lamp
ORDER REPLACEMENT LAMP
Replacement lamp can be ordered through your projector
● Replacement Lamp Type No.
: PLC-XL50
: POA-LMP121
(Service Parts No. 610 337 9937)
62
The glass can become very hot. of...
Instruction Manual, PLC-XL50 - Page 63
... trained to Reset and then press the SELECT button. No one IMMEDIATELY after the projector has cooled down.
(Follow carefully the instructions in which must be cleaned up , replace the lamp with a new one should be handled carefully and properly. Inappropriate attempts to service the unit by pieces of broken glass.
63 If you select Reset...
Instruction Manual, PLC-XL50 - Page 66
... to set the Alarm setting again. Your operation is a Directive conformity mark of fire, casualty and electrical hazards.
Specify the model number and explain about the problem. Pixelworks ICs used to that the Terminal function can be selected after following all operating instructions, contact the dealer where you purchased the projector or the service center.
This...
Instruction Manual, PLC-XL50 - Page 74
... body to operate the projector, contact the service station. XXX-XXXXXX
Lamp Replacement Label
When using the projector ceiling-mounted, put the Lamp replacement label (supplied) on in a prominent place of the projector's body while the Antitheft alarm function is locked with the PIN code...
Factory default set .
74
Model No. XXXXXX Type No. XXX-XXXX Replacement Lamp No.
Put the...
Instruction Manual, PLC-XL50A - Page 4
.... Operating the projector properly enables you purchased the projector or the service center. If the problem still persists, contact the dealer where you to operate improperly, read this manual again, check operations and cable connections, and try the solutions in the "Troubleshooting" section in other accidents. NO USER-SERVICEABLE PART S I N S I D E E XC E P T LAMP REPLACEMENT.
Instruction Manual, PLC-XL50A - Page 30
...8 buttons to show the information of this projector. Current mode Press the SELECT button to adjust the horizontal picture position.
The projector has five independent memory areas (Mode 1-5) ...match those parameters manually adjusted, which may not be tuned by Multi-scan system of the connected computer. Manual PC Adjustment enables you to recall the setting for a specific computer.
1...
Instruction Manual, PLC-XL50A - Page 48
... code. For details on PIN code setting, refer to "Set" by pressing the Point ed buttons. Setting
48
Logo PIN code lock
This function prevents an unauthorized person from the Logo select menu (p.47).
On......the screen logo can no . Repeat this step to "✳".
After entering the four-digit number, move the pointer to relevant instructions...
Instruction Manual, PLC-XL50A - Page 56
... frame pointer to the Setting Menu icon. Select [Yes] again to clean, replace it with dust particles, it . • If the filter is heavily clogged and unable to reset the Filter counter.
56 Clean the air filter by using a brush or blower. CAUTION Do not operate the projector with water and any other liquid matter. Replacement Filter Part No.: 610 335...
Instruction Manual, PLC-XL50A - Page 58
....
Follow these steps to the dealer.
● Model No.
See "Lamp Replacement Counter" on the screen and LAMP REPLACE indicator lights yellow.
The glass can be ordered through your projector
● Replacement Lamp Type No.
: PLC-XL50A
: POA-LMP139
(Service Parts No. 610 347 8791)
58 Lift the lamp out of the projector can become very hot. Screw Handle
Screw
✔...
Instruction Manual, PLC-XL50A - Page 59
... and properly. Maintenance and Cleaning
Lamp Replacement Counter
Be sure to reset the Lamp replacement counter after replacing the lamp. Select "Yes," then another confirmation box appears. When the Lamp replacement counter is no broken shards or pieces of the lamp with projector service. Use the Point 7 8 buttons to move the red frame pointer to the Setting Menu icon.
2 Use the...
Instruction Manual, PLC-XL50A - Page 71
... set No: 4 3 2 1* *Should the four-digit number be invalid. Appendix PIN Code Number Memo
Write down the PIN code number in the column below (supplied) to operate the projector, contact the service station.
PIN Code Lock No. If you forgot or lost the number and unable to a prominent place of the projector's body while it with this manual...
Sanyo XL50 Reviews
We have not received any reviews for Sanyo yet.