Sanyo PLC-HF10000 Support and Manuals
Get Help and Manuals for this Sanyo item
View All Support Options Below
Free Sanyo PLC-HF10000 manuals!
Problems with Sanyo PLC-HF10000?
Ask a Question
Free Sanyo PLC-HF10000 manuals!
Problems with Sanyo PLC-HF10000?
Ask a Question
Popular Sanyo PLC-HF10000 Manual Pages
Owners Manual - Page 2
...
Operation menu is available in 12 languages; For details, refer to control and set the timer. With the Key lock function, you want. Features and Design
This Multimedia Projector is designed with the motor-driven lens shift function. Supported resolution up the projector remotely via network. English, German, French, Italian, Spanish, Portuguese, Dutch, Swedish, Russian...
Owners Manual - Page 4
... the unit. Operating the projector properly enables you purchased the projector or the service center. Otherwise it in good condition for an extended time, unplug the projector from the projection lens.
To The Owner
Before installing and operating the projector, read this manual again, check operations and cable connections and try the solutions in the "Troubleshooting" section in the...
Owners Manual - Page 17
... used and prepare a suitable lens. Lens installation and replacement should be performed by the qualified service personnel. - When setting the projector after lens installation, be careful not to put your hands on lens part. Loop Hole Fig. 2
5 Fit the lens mount cover, align the matchmark on the lens mount cover with this projector.
Do not use the optional lens below for use with...
Owners Manual - Page 59
...projected image, go to the Logo select function and set logo. Then the captured image will be selected, you to the manual of presentations. To cancel the capture function, select Yes...is automatically reset and the projector captures an image without keystone correction.
• When Logo PIN code lock is set to On, Capture cannot be selected.
Settings
HDMI setup
Select Normal or Enhanced ...
Owners Manual - Page 60
... ed buttons to switch On or Off, and then press the SELECT button to enter a number (p.16). If you can change the Logo PIN code lock setting. Off The screen logo can be changed freely from changing the screen logo. On The screen logo cannot be changed to correct, and then enter...
Owners Manual - Page 74
... Function.
Lamp Status Display
The Lamp Status Display appears on screen when the projector is turned on the LAMP 1/2 REPLACE indicators. Red Lamp X Mark on pages 54, 55.
2 LAMPS MODE
1 LAMP MODE
When Lamp 1 is burnt out.
Refer to the SETTING section on Lamp
Projection Lamp is nearing its end, and flash when...
Owners Manual - Page 76
...down. (Follow carefully the instructions in an accident or injury caused by anyone, especially those who are authorized trained technicians and who are no guarantee of broken glass.
76 Maintenance and Care
ORDER REPLACEMENT LAMP
Replacement Lamp can be ordered through your projector
:
PLC-HF10000L
● Replacement Lamp Type No. :
POA-LMP146
(Service Parts No. 610 351 5939...
Owners Manual - Page 91
...) AC 100-240 V (11.2 - 4.6 A Max. Appendix
Technical Specifications
Mechanical Information
Projector Type
Multi-media Projector
Dimensions (W x H x D)
21.20" (W) x 10.55" ...Lens Attachments (1 type) (For optional lens) q Light Block Plates (3 types) (For optional lens) q Spacer (For optional lens) q Strap (For lens mount cover) q Owner's Manual (CD-ROM) q Quick Reference Guide q PIN Code...
Network Setup - Page 20
... tab. * Each item has a valid setting range respectively. or + button.
The setting value exceeding this case, the values of the projector you use the setting menus on the web browser. Describes the basic operation and procedures commonly used depending on this manual.
Pull-down menu button and then click Set button.
✐ The value in the...
Network Setup - Page 28
... the AC power cord and plug it with the error information.
● When PJ lamp replacement time is set to your selected condition. MAIN, 3.3V NG
---
--- --- Lamp 1 ON 2000 h Lamp 2 ON 1800 h
✐ Replace it , and then turn the projector on the projector once again to a qualified service personnel with a new lamp immediately and reset the lamp...
Network Setup - Page 43
... code, Network setting
* This function is not replaced. Reset the time after filter cartridge replacement. Gradation4, All white, All black, Cross)
Factory default....Sets all of the filter.
ENGLISH
43 Filter warning.....Sets the time to indicate the filter warning message on the screen. (OFF, 400H, 700H, 1000H)
Scrolls remaining...Displays the scrolls remaining of the projector...
Network Setup - Page 51
... 4
C1C
Menu display on
C1D
Menu display off
*1 F urther instructions about the telnet application, please see the on-line guide on the keyboard.
Please try again for controlling this projector and please consult your computer.
*2 The password is a Network PIN code decided item "Network PIN code setting" (☞pp.14, 23). Please try again for more than...
Network Setup - Page 54
... your network administrator. - For further instruction please consult your web browser's the proxy server settings according to the local area network environment to the computer directly with UTP cross cable, this must be unchecked. If you connect the projector to which the projector is connected. -
Chapter 5 Appendix
Proxy setting Select Internet Options from the local...
Network Setup - Page 55
.... For further instruction please consult your web browser's the proxy server set up your network administrator.
- If you use the proxy server when accessing the projector installed in the Category column.
Make sure that will not use an external internet connection from the local area network, select the item Manual proxy configuration.
Properly set - tings according...
Network Setup - Page 56
...network environment to configure. For further instruction please consult your web browser Safari's the proxy server set- If you connect the projector to configure window and enter the ...setting
1 Open Preferences... from Safari menu on the web browser and then select Security tab and check Enable JavaScript. Using proxy server To use the proxy server when accessing the projector installed...
Sanyo PLC-HF10000 Reviews
We have not received any reviews for Sanyo yet.