SanDisk SDCFXP-064G-P91 - 64GB Extreme Pro Compact Flash CF Support and Manuals
Get Help and Manuals for this SanDisk item
View All Support Options Below
Free SanDisk SDCFXP-064G-P91 manuals!
Problems with SanDisk SDCFXP-064G-P91?
Ask a Question
Free SanDisk SDCFXP-064G-P91 manuals!
Problems with SanDisk SDCFXP-064G-P91?
Ask a Question
Popular SanDisk SDCFXP-064G-P91 Manual Pages
Product Manual - Page 28
...
CE Setup Time CE Setup Time CE Recover Time VCC Rising Timeb VCC Falling Timeb Reset Width
Symbol Vi (CE)
TSU (VCC) TSU (RESET) TREC (VCC)
tpr tpf TW (RESET) Th (Hi-z Reset) TS (Hi-z Reset)
Condition 0V Interface Description
SanDisk CompactFlash Card OEM Product Manual
3.3.3
Power Up/Power Down Timing
The timing specification in...
Product Manual - Page 29
... the system driver/receiver to the card must be accounted for by pull-up resistor on card (if present)
tpf
VCC Min.
trec
VIH
2V
3.3.4
Common Memory Read Timing Table 3-10 contains common memory read timing specifications for Systems not supporting RESET
tpr
VCC Min. Skews and delays from Add Changea Address Setup Time...
Product Manual - Page 47
... and adapters to register 9 are not supported. Register 8 is pro vided ...-CE2 high.
SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
...instruction.
b. Byte accesses to register 9 access only the odd byte of byte accesses to even addresses between 400h and 7FFh access register 9. Accesses to the offset 0 with CE1 high and CE2 low accesses the error...
Product Manual - Page 49
...[173]; Offset 2)
This register contains the number of sectors of an error when an error is detected. D3
0
Bit set to 0.
SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
Table 4-6 Data Register
Data Register Error/Feature Register Error/Feature Register
CE2- Bit
Name
Description
D7
BBK
Set when a bad block is indicated in order to 0. CE1-
Product Manual - Page 51
... to or from accessing the command register
and buffer. D2
CORR
Set when a correctable data error has been encountered and the data has
been corrected.
The bits
... The meaning of error. D4
DSC
Set when the card is ready to a 1.
This condition does not terminate a multi-sector read by the host. SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
4.5.9
...
Product Manual - Page 53
...problem for the PCMCIA implementation:
1. Implementation Note:
Conflicts may be programmed to (conditionally) tri-state D7 of I/0 address 3F7/377 when a CompactFlash Memory Card is installed... in the Drive/Head Register. D4
-HS2
This bit is unknown. SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
Card (Drive) Address Register (con't)
Bit
Name
Description
D7...
Product Manual - Page 56
...CY Cylinder Registers
DH Card/Drive/Head Register
LBA Logical Block Address Mode Supported
Y
The register contains a valid parameter for this command.
Y Y...-
b.
ATA Command Description
SanDisk CompactFlash Card OEM Product Manual
Table 5-1 Primary and Secondary I/O Decoding
Class 1 1 1 1 1 1 2 2 2 3 3 2 2 2
Command Set Multiple Mode Set Sleep Mode Stand By Stand...
Product Manual - Page 59
.../Write Long Commands Firmware revision in ASCII (Rev M.ms) set by code Big Endian Byte Order in Word Model number in ASCII (left justified) Big Endian Byte Order in the Identify Device Information. The parameter words in the buffer have the arrangement and meanings defined in Table 5-8. SanDisk CompactFlash Card OEM Product Manual
ATA Command Description...
Product Manual - Page 64
...Write cache supported
6
1
Look-ahead supported
7
0
Release Interrupt not supported
8
0
Service Interrupt not supported
9
0
Device Reset command not supported
10
0
Host Protected Area feature set not supported by host implementers.
Words 82, 83, and 84 indicate the features and command sets supported. ATA Command Description
SanDisk CompactFlash Card OEM Product Manual
Word 68...
Product Manual - Page 65
... not enabled
8
0
Service Interrupt not enabled
9
0
Device Reset command not supported
10
0
Host Protected Area feature set not supported by host implementers. The older modes are reserved.
This word describes the capabilities and current settings for CFA defined advanced timing modes using the True IDE interface. SanDisk CompactFlash Card OEM Product Manual
ATA Command...
Product Manual - Page 70
...is for n sectors, where: n = (sector count)-module (block count).
The error reporting is programmed by the Set Multiple Mode command, which contains the number of blocks or the block count) requested.... to the Read Multiple command.
If an error occurs, the read . ATA Command Description
SanDisk CompactFlash Card OEM Product Manual
5.1.11
Read Multiple-C4H
The Read Multiple ...
Product Manual - Page 73
... 15-8)
Sec Num (3)
Sector Number (LBA 7-0)
Sec Cnt (2)
X
Feature (1)
X
© 2007 SanDisk Corporation
5-19
Rev. 12.0, 02/07 SanDisk CompactFlash Card OEM Product Manual
ATA Command Description
Table 5-24 defines the valid extended error codes for the CompactFlash Memory Card Series product.
The extended error code is out of cylinder and head or LBA address and returns...
Product Manual - Page 74
... 01H feature command is issued, all features that are used by the host to CompactFlash Memory cards and are not part of the ATA Specification. ATA Command Description
SanDisk CompactFlash Card OEM Product Manual
5.1.18 Set Features-EFH
This command is used to enable and clear 8-bit data transfer mode. The 9AH feature is unique...
Product Manual - Page 105
... in systems designed with the published specifications, or of its products to SanDisk for one year of purchase, SanDisk will repair, replace or refund the purchase price of SanDisk's responsibilities regarding the SanDisk SD Card. WHAT THIS WARRANTY COVERS
For products found of abuse or operation of products not in life support systems or other applications where failure...
Product Manual - Page 106
... was not covered under the warranty. V. IV. If approved, SanDisk will be tested to the product's functional and performance specifications.
RECEIVING WARRANTY SERVICE
According to market any product returned by the above provisions, then the product will issue a Return Material Authorization or Product Repair Authorization number and provide a shipping address where the defective...
SanDisk SDCFXP-064G-P91 Reviews
We have not received any reviews for SanDisk yet.