SanDisk SDCFH-4096 - 4GB ULTRA II Compact Flash Bulk Package Support and Manuals
Get Help and Manuals for this SanDisk item
This item is in your list!
View All Support Options Below
Free SanDisk SDCFH-4096 manuals!
Problems with SanDisk SDCFH-4096?
Ask a Question
Free SanDisk SDCFH-4096 manuals!
Problems with SanDisk SDCFH-4096?
Ask a Question
Popular SanDisk SDCFH-4096 Manual Pages
Product Manual - Page 28
...
CE Setup Time CE Setup Time CE Recover Time VCC Rising Timeb VCC Falling Timeb Reset Width
Symbol Vi (CE)
TSU (VCC) TSU (RESET) TREC (VCC)
tpr tpf TW (RESET) Th (Hi-z Reset) TS (Hi-z Reset)
Condition 0V
Interface Description
SanDisk CompactFlash Card OEM Product Manual
3.3.3
Power Up/Power Down Timing
The timing specification in...
Product Manual - Page 29
... the system driver/receiver to the card must be accounted for all types of memory. SanDisk CompactFlash Card OEM Product Manual
Interface Description
Figure 3-2 Power Up/Power Down Timing for Systems not supporting RESET
tpr
VCC Min.
NOTE: All timings measured at the CompactFlash Memory Card.
Table 3-10 Common Memory Read Timing Specification
Speed Version...
Product Manual - Page 47
... to register 9 are not supported.
Repeated byte accesses to register 0 with CE1 high and CE2 low accesses the error (read) or feature (write) register. Accesses to register 9 access only the odd byte of the data. b.
Byte accesses to odd addresses between 400h and 7FFh access register 8. SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
4.3
Memory...
Product Manual - Page 49
... write operation between the host and the card. CE1- This register is specified. If the command was successful, this register is zero, a count of an error when an error is "0" at command completion. D5
0
Bit set to 0. SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
Table 4-6 Data Register
Data Register...
Product Manual - Page 51
...the command register
and buffer. No other bits in the Error Register contain additional information describing the error.
4.5.10 Device Control Register (Address-3F6[376];
Offset Eh)
This register is set , indicates a write fault has occurred. SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
4.5.9
Status & Alternate Status Registers (Address-1F7[177]&3F6...
Product Manual - Page 53
...install a Floppy and a CompactFlash Memory Card in the card that can be accomplished by a Floppy Disk Controller operating at primary addresses.
2. This may occur on the host data bus when this problem...bit is 0 when the drive 0 is active and selected.
SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
Card (Drive) Address Register (con't)
Bit
Name
...
Product Manual - Page 56
...
SN Sector Number Register
CY Cylinder Registers
DH Card/Drive/Head Register
LBA Logical Block Address Mode Supported
Y
The register contains a valid parameter for this command. E6h or 99h -
-
-
-...Command Description
SanDisk CompactFlash Card OEM Product Manual
Table 5-1 Primary and Secondary I/O Decoding
Class 1 1 1 1 1 1 2 2 2 3 3 2 2 2
Command Set Multiple Mode Set Sleep Mode...
Product Manual - Page 59
... of sectors per card (Word 7 = MSW, Word 8 = LSW) Reserved Serial number in ASCII (right justified) Buffer type (dual ported) Buffer size in 512 byte increments Number of Sectors on Read/Write Long Commands Firmware revision in ASCII (Rev M.ms) set by code Big Endian Byte Order in Word Model number in ASCII (left justified) Big Endian...
Product Manual - Page 64
... Rev. 12.0
5-10
© 2007 SanDisk Corporation Obsolete
12
1
Write Buffer command supported by CF Card
13
1
Read Buffer command supported by CF Card
14
1
NOP command supported by CompactFlash cards prior to zero which indicates that features/command sets supported are not indicated. ATA Command Description
SanDisk CompactFlash Card OEM Product Manual
Word 68: Minimum PIO Transfer...
Product Manual - Page 65
...
Bit
Setting
Indication
0
0
SMART feature set not enabled
1
1
Security Mode feature set enabled via the Security Set Password command
2
0
Removable Media feature set not supported
3
1
Power Management feature set supported
4
0
Packet Command feature set not enabled
5
1
Write cache enabled
6
1
Look-ahead enabled
7
0
Release Interrupt not enabled
8
0
Service Interrupt...
Product Manual - Page 70
... operation except that the number of the sector where the error occurred. Interrupts are generated when DRQ is set and the data transfer will take place as it normally would...A sector count of blocks or the block count) requested. ATA Command Description
SanDisk CompactFlash Card OEM Product Manual
5.1.11
Read Multiple-C4H
The Read Multiple command performs similarly to 256 sectors as...
Product Manual - Page 73
... sector invalid) Address overflow (address too large) Supply or generated voltage out of range. SanDisk CompactFlash Card OEM Product Manual
ATA Command Description
Table 5-24 defines the valid extended error codes for the CompactFlash Memory Card Series product.
The extended error code is returned to the card although it does perform a range check of cylinder and...
Product Manual - Page 74
... Command Description
SanDisk CompactFlash Card OEM Product Manual
5.1.18 Set Features-EFH
This command is used to establish or select certain features. Disable Read Look Ahead Disable Power on Reset (POR) establishment of defaults at Soft Reset. If the 01H feature command is unique to CompactFlash Memory cards and are not part of defaults...
Product Manual - Page 103
... (MB) = 1 million bytes; 1 gigabyte (GB) = 1 billion bytes. of the listed capacity is used for formatting and other functions, and thus is not available for data storage.
© 2007 SanDisk Corporation
A-1
Rev. 12.0, 02/07 Part Number SDCFJ-128-388 SDCFJ-256-388 SDCFJ-512-388 SDCFJ-1024-388 SDCFJ-2048-388 SDCFJ-4096-388 SDCFH-1024-388 SDCFH-2048-388 SDCFH-4096-388 SDCFH-8192-388 SDCFH-16384...
Product Manual - Page 106
... the product's functional and performance specifications.
or improper alterations or repairs. Limited Warranty
SanDisk CompactFlash Card OEM Product Manual
All failing products returned to SanDisk under the provisions of this limited warranty shall be returned only with prior authorization from SanDisk Corporation.
SanDisk reserves the right to repair or replace, at its discretion, any...
SanDisk SDCFH-4096 Reviews
Do you have an experience with the SanDisk SDCFH-4096 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for SanDisk yet.
Earn 750 points for your review!