Samsung STP-103PG Support and Manuals
Get Help and Manuals for this Samsung item
View All Support Options Below
Free Samsung STP-103PG manuals!
Problems with Samsung STP-103PG?
Ask a Question
Free Samsung STP-103PG manuals!
Problems with Samsung STP-103PG?
Ask a Question
Popular Samsung STP-103PG Manual Pages
User Manual - Page 1
USER'S MANUAL
STP-103
THERMAL PRINTER
KN04-00003A Rev. 2.6
POWER ERROR
FEED
ON LINE
www.samsungminiprinters.com
User Manual - Page 2
... unplug the set from the printer, unplug it can be electrocuted. PROHIBITED
TO UNPLUG
PRINTER
WARNING
Violating following safety regulations in the printer.
Safety Precautions
In using the present appliance, please keep the following instructions can cause slight wound or damage the appliance. multi-outlet. ONLY SUPPLIED ADAPTER
PROHIBITED
Do not pull the cable to use...
User Manual - Page 3
...interference regulations. If this manual carefully before using your new STP-103S and STP-103P. Introduction
The STP-103 and STP-103P Roll Printer are designed to correct the interference by DIP switches. RS-232 serial interface (STP-103S), Parallel interface (STP-103P). 4. Different print densities can radiate radio frequency energy and, if not installed and uses in the Canadian...
User Manual - Page 4
... 11
Chapter 3. Code Table 18
Chapter 8. Functions 27
Chapter 9. Connectors 51 - Parallel Type (STP-103P 51
APPENDIX B - Locating the Printer
Avoid location in the place subject to intense vibration or shock. Make sure that there is enough space around the printer so that it can be used easily.
7 Printer Part names 8 1-4. Operating Control Panel 9
Chapter 2. Installing the Paper...
User Manual - Page 5
... out. 2) The error LED blinks when the Near End Sensor triggered.
9 Printer Part Names
(10)
(1) Cover top (2) Case top (3) Case bottom (4) Control panel (5) Roller (6) Power switch (7) Interface connector (male) (8) DC Jack (9) Interface connector (female) (11) (10) Roll paper (11) Detector switch
(5) (1)
Rear View
(2) (4)
Rear View
(6)
(7)
(8)
STP-103S
Control Panel
POWER ERROR
FEED ON...
User Manual - Page 6
... voltage matches that the main unit's power cord is unplugged from the electrical outlet.
2.
Connecting the printer to your Computer
STP-103S You need an appropriate serial interface cable to connect your printer. Plug the other end of the cable connector.
25 Pin Female Type
3. Plug the AC adapter's power cord into the computer.
4. Make sure...
User Manual - Page 7
... before installing the paper roll. 1. Open the printer cover and remove the used paper roll core if there is one. 2. Pull out the paper roll until the paper comes out from the top of the cable connector.
25 Pin Female Type
Chapter 3. Connecting the printer to your Computer
STP-103P You need an appropriate parallel interface cable...
User Manual - Page 9
.... The self-test prints the current printer settings, which provide the following information :
- Chapter 6.
Running the Self-test
1. Ending the self-test
After a number of lines are printed, the printer indicates the end of the self-test by printing " ** TEST COMPLETED ** ". Turn on the printer with a guide section to the printer. When the printing finishes, turn...
User Manual - Page 16
... Not used . DLE ENQ n
[Name]
Real time request to printer
[Format]
ASCII
DLE ENQ n
HEX
10
05
n
DECIMAL 16
5
n
[Range]
1≤ n ≤2
[Description] Respond to a request from an error after clearing the receive and print buffers
ESC SP n [Name] [Format]
[Range] [Description]
Set right-side character spacing
ASCII
ESC
SP
n
Hex
1B
Decimal...
User Manual - Page 18
... was in the print buffer and feeds the paper [n X
(vertical or horizontal motion unit)] inches.
35 Printer enabled. n [Name] [Format]
[Range] [Description]
Cancel user-defined characters
ASCII ESC ?
Undefined. Undefined. ESC D n1...nk NUL
[name]
Set horizontal tab positions
[Format]
ASCII Hex
ESC
D n1...nk NUL
1B
44 n1...nk 00
[Range...
User Manual - Page 20
... ASCII
ESC
t
n
Hex
1B
74
n
Decimal 27
116
n
0 ≤n ≤5, n = 11, 255
Selects a page n from the character code table. n
Page
0
0 : PC437 [U.S.A., standard Europe]
1
1 : Katakana
2
2 : PC850 [Multilingual]
3
3 : PC860 [Portuguese]
4
....
Even if a paper
feed amount of more than 40 inches is set, the printer feeds the
paper only 40 inches.
● When label mode is ...
User Manual - Page 22
... the number of times to 0, the default setting value is used . n selects the printing position as follows:
n
Printer ID
Specification
ID(hexadecimal)
1,49 Printer model ID STP-103S / STP-103P
30
2,50
Type ID
02
3,51 ...code
2,50 Below bar code
3,51 Both above and below the bar code
[Default]
● HRI indicates Human Readable interpretation. When y is set to 1/x inch...
User Manual - Page 24
...
d1...dn
(k and d depends on the bar code system used)
(n and d depends on the bar code system used :] ● The printer prints an HRI character (□) as start character ...h n [Name] [Format]
[Range] [Description]
[Default]
Set bar code height
ASCII
GS h
n
Hex
1D
68
n
Decimal
29
104
n
1 ≤n ≤255
Sets the height of dots in the vertical direction. n specifies the ...
User Manual - Page 25
...* If the top of the bar code data is not the code set selection character, the printer stops command processing and processes the following ...space. In code set C, only FNC 1 is defined by combining one of the 103 bar code characters and 3 code sets.
In code set B, the character just after SHFIT is processed as a character for code set B. Specific character
SHIFT CODE A CODE B CODE C
FNC1 FNC2...
User Manual - Page 26
...APPENDIX A : CONNECTORS
Serial Interface Connector (STP-103S)
PRINTER
20
TXD (O)
19
RXD (I)
21
CTS (I)
22~25
GND
18
RTS (O)
FGND
25 PINE MALE
CONNECT
HOST
2
RXD (I)
3
TXD (O)
7
RTS (O)
5
GND
8
CTS (I)
4
DTR (O)
6
DSR (I)
FGND
9 PINE FEMALE
Parallel Interface Connector (STP-103P)
PRINTER
1
/STROBE (I/O)
2
DATA0 (I/O)
3
DATA1 (I/O)
4
DATA2 (I/O)
5
DATA3...
Samsung STP-103PG Reviews
We have not received any reviews for Samsung yet.