Ryobi TS1346 Support and Manuals
Get Help and Manuals for this Ryobi item
View All Support Options Below
Free Ryobi TS1346 manuals!
Problems with Ryobi TS1346?
Ask a Question
Free Ryobi TS1346 manuals!
Problems with Ryobi TS1346?
Ask a Question
Popular Ryobi TS1346 Manual Pages
Operation Manual - Page 1
... operator safety.
Thank you for , it will give you years of rugged, trouble-free performance. SAVE THIS MANUAL FOR FUTURE REFERENCE OPERATOR'S MANUAL
10 in. (254 mm) Compound Miter Saw
Model TS1340 - Double Insulated
Your new Miter Saw has been engineered and manufactured to Ryobi's high standards for dependability, ease of injury, the user must read and...
Operation Manual - Page 2
... read thoroughly and understand completely the operator's manual.
We recommend Wide Vision Safety Mask for...Specifications ...2 I Rules for Safe Operation ...3-6 I Glossary of Terms ...6 I Unpacking and Tools Needed ...7 I Loose Parts ...8 I Features ...9-11 I Assembly ...12-14 I Adjustments ...15-18 I Operation ...18-25 I Maintenance ...26 I Parts Ordering/Service ...28
INTRODUCTION
Your saw...
Operation Manual - Page 3
... that may appear on this product.
Save operator's manual and review frequently for continuing safe operation, and instructing others who may cause property damage. SAFETY AND INTERNATIONAL SYMBOLS
This operator's manual describes safety and international symbols and pictographs that may use only identical Ryobi replacement parts. DOUBLE INSULATION
Double insulation is a concept in...
Operation Manual - Page 4
..., or other part that is in doubt, use , before servicing, or when changing attachments, all guards are operating properly before turning on the saw 's applications and...SET. Everyday eyeglasses have repaired at the rate for an extension cord 25 feet or less in good condition. I DO NOT FORCE THE TOOL it is damaged should wear safety glasses and be properly repaired or replaced...
Operation Manual - Page 5
... All repairs, whether electrical or mechanical, should any reason. I NEVER TOUCH BLADE or other parts may slip...SERVICING, use of the workpiece. I ALWAYS SUPPORT LONG WORKPIECES while cutting to move into the blade.
I NEVER stand or have any other moving parts... saw ) to clean tool. I BEFORE MAKING A CUT, be sure all nails from frequent use only identical Ryobi replacement parts...
Operation Manual - Page 8
Page 8
LOOSE PARTS LIST
The following items are included with your Compound Miter Saw:
I 10 in. (254 mm) Saw Blade
I Work Clamp
I Miter Lock Handle
I Blade Wrench
I Dust Bag
I Operator's Manual
I Dust Guide
I Warranty Registration Card
DUST BAG
BLADE WRENCH
SAW BLADE
DUST GUIDE
5
MITER LOCK HANDLE
WORK CLAMP Fig. 1
WARNING: The use of attachments or accessories not...
Operation Manual - Page 14
... parts, making very accurate cuts. ASSEMBLY
CAUTION:
Always install the blade with an arrow on the side of the blade pointing down at the factory for making adjustments, installing ... in this manual show points being made in good operating condition. Never operate your saw . After unpacking your saw, check the following adjustments before reconnecting saw .
I Replace the lower blade...
Operation Manual - Page 17
... the miter lock handle approximately one on the control arm is positioned at 0° bevel (blade set saw blade to -table alignment. Recheck blade-to the miter table at several points.
ADJUSTMENTS
SQUARING THE...
See Figure 20. Page 17
Note: Make sure that the square contacts the flat part of the saw arm at 0°.
I Depress the miter lock plate and rotate the miter table ...
Operation Manual - Page 18
...reach full speed, then carefully make another cut the slot, set your saw at your compound miter saw without holding workpiece against the fence). APPLICATIONS
(Use only for ...saw. Turn your nearest RYOBI AUTHORIZED SERVICE CENTER. The slot in the pivot joints, have saw repaired by at any angle from 0° to 45°. I If the saw arm does not raise by at 0° miter, turn your saw...
Operation Manual - Page 20
...zero on the miter table with the saw arm has been set at the desired angle, securely tighten the bevel lock knob.
Failure to make sure that no problems will seat itself in movement of the... and 27. I Once the saw table. I Place the workpiece flat on
the miter scale.
A straight bevel cut . I When cutting long pieces of lumber or molding, support the opposite end of the control...
Operation Manual - Page 21
...the interaction of the control arm or miter table while making compound miter setups due to secure the workpiece when possible. Never perform any cutting operation freehand...seconds for a particular cut . I Before turning on the saw arm must be checked after setting the second angle, since adjusting the second angle affects the ...problems will seat itself in . (7.6 cm) from miter table.
Operation Manual - Page 28
... www.ryobitools.com for repair parts or service, simply contact your nearest Ryobi Authorized Service Center.
Please call or visit. OPERATOR'S MANUAL
10 in the space provided below.
• MODEL NUMBER • SERIAL NUMBER
TS1340
983000-248 3-03
RYOBI TECHNOLOGIES, INC.
1428 Pearman... area. Please record the serial number in . (254 mm) Compound Miter Saw Model TS1340 -
Parts Diagram - Page 3
...found on a plate attached to the motor housing. Always mention the model number in . (254 mm) COMPOUND MITER SAW - Number
S58000500 1 580118000 2 A07103080457 3 A36030814204 4 A19003040093 5... 1 TABLE INSERT 1 * SCREW (M4 X 8 mm 4
* Standard Hardware Item -
RYOBI 10 in all correspondence regarding your Compound Miter Saw or when ordering repair parts. May Be Purchased Locally 3 MODEL NO.
Parts Diagram - Page 5
... WASHER (M12 1 C-RING 1 BEARING 1 O-RING 1 ARM 1 SPINDLE LOCK PIN 1 E-RING 1 COMPRESSION SPRING 1 ARBOR ASSEMBLY 1 * SPECIAL SCREW (M5 X 10 mm 2
* Standard Hardware Item - RYOBI 10 in all correspondence regarding your Compound Miter Saw or when ordering repair parts.
FIGURE B
Description
Qty. TS1340
The model number will be found on a plate attached to the motor housing.
Parts Diagram - Page 8
...number in . (254 mm) COMPOUND MITER SAW - Key Part No.
TS1340
The model number will be found on a plate attached...(M4 X 10 mm 2 PIVOT SUPPORT 1 LOCK BOLT 1 WASHER 1 PIVOT SHAFT 1 * FLAT WASHER (M10 1 HANDLE 1 TENSION SPRING 1 OPERATOR'S MANUAL REPAIR SHEET
* Standard Hardware Item - RYOBI 10 in all correspondence regarding your Compound Miter Saw or when ordering repair parts.
Ryobi TS1346 Reviews
We have not received any reviews for Ryobi yet.