Ryobi CSB134L Support and Manuals
Get Help and Manuals for this Ryobi item
View All Support Options Below
Free Ryobi CSB134L manuals!
Problems with Ryobi CSB134L?
Ask a Question
Free Ryobi CSB134L manuals!
Problems with Ryobi CSB134L?
Ask a Question
Popular Ryobi CSB134L Manual Pages
Operation Manual - Page 2
... Figure Numbers (Illustrations)...17-20
Parts Ordering / Service...Back Page
INTRODUCTION
This product has many features for making it was purchased. Box 1207, Anderson, SC 29622-1207, by calling 1-800-525-2579 or by returning the power tool to you may either repair or replace any RYOBI® power tool which includes the date of purchase (for...
Operation Manual - Page 3
... or battery-operated (cordless) power tool. The correct power tool will increase the risk of the power tool in unexpected situations. Any power tool that may result in the warnings refers to operate the power tool. WORK AREA SAFETY
Keep work area clean and well lit. Many accidents are provided for which may result in moving parts.
Save all instructions...
Operation Manual - Page 4
...grip with these instructions, taking into the top surface of blade binding.
4 - Use of the blade, but kickback forces can not protect you from those intended could cause the saw to a complete stop. Never attempt to remove the saw will also make exposed metal parts of control.
Hold power tool by a qualified repair person using only identical replacement parts.
Operation Manual - Page 5
..." and "compound cuts." Raise lower guard by an authorized service center. A cord exceeding 100 feet is damaged should be properly repaired or replaced by retracting handle and as soon as the specific potential hazards related to carry the current your power tool. Supports must be carefully checked to damaged parts, gummy deposits, or a build-up or kickback from...
Operation Manual - Page 7
... extension cord, inspect it will draw. Use the chart to do not need for repair. Only round jacketed cords listed by a qualified service technician. NOTE: Servicing of a product with double insulation requires extreme care and knowledge of the working with a power tool.
NOTE: AWG = American Wire Gauge
WARNING:
Keep the extension cord clear of the system...
Operation Manual - Page 8
Cutting Depth at 45 1-7/8 in. No Load Speed 5,000 r/min. (RPM) Input 120 V, AC only, 60 Hz, 13 A Net Weight 7.5 lbs. Cutting Depth at 51.5 1-11/16 in . Laser Guide Class IIIa,
FEATURES
PRODUCT SPECIFICATIONS
Blade Diameter 7-1/4 in . Cutting Depth at 0 2-7/16 in . Blade Arbor 5/8 in .
Operation Manual - Page 10
...
Failure to the circular saw .
10 - Blade stalling is caused by the blade. DANGER:
Release switch immediately if blade binds or saw and increase the danger of kickback, follow these accumulations. Loss of any kind with a dull, gummed up, or improperly set blades. This helps prevent twisting the blade. Use clean, sharp, and properly set blade
Supporting the workpiece...
Operation Manual - Page 11
..., then guide the saw : Depress the switch. More blade depth will increase the chance of the cut on underside of work , keep correct blade depth setting.
Adjusting the laser may be necessary. Mark the line to be cut as needed and lock
the depth and bevel settings. Connect the saw to a power supply. ...
Operation Manual - Page 12
... to prevent it replaced before setting the saw until the lower blade guard closes.
DANGER...guide. WARNING:
Use clamps or other practical way to secure and support the workpiece to "TO ADJUST BEVEL SETTING" section.
12 - Holding the work by holding the saw blade and can measure. Unplug the saw from the cutting area. The saw firmly with the saw .
NOTE: Do not bind the blade...
Operation Manual - Page 13
... rip
cut in loss of control of the saw possibly causing serious injury.
■ Adjust the bevel setting to zero. Set the blade to the width needed. Tighten edge guide lock knob securely. OPTIONAL EDGE GUIDE
See Figure 23, page 20. Use the optional edge guide kit, part no . 200673002, for the cut to avoid...
Operation Manual - Page 14
...power supply.
Depress and hold the switch until square with the notch in serious injury.
If the lever prematurely contacts any part of the saw base and the guideline you drew on the depth lock lever. The base should align with
saw blade...of cut position and lock the depth setting by following these steps:
Unplug the saw.
Pull depth lock lever ...
Operation Manual - Page 15
...remove dirt, dust, oil, grease, etc. Use clean cloths to comply with plastic parts. However, if you do so could result in objects being thrown into your eyes... tools used on these materials, it is extremely important to avoid a safety hazard.
15 -
MAINTENANCE
WARNING:
When servicing, use . Use of the power supply cord is required.
POWER SUPPLY CORD REPLACEMENT
If replacement of...
Parts List - Page 2
RYOBI 7-1/4 in damages to the double insulation system possibly causing electrical shock or electrocution. MODEL NUMBER CSB134L
29 30...repair of your tool requires safety testing and should only be performed by a Ryobi Authorized Service Center. For the service center nearest you call 1-800-525-2579.
2 Any repairs requiring disassembly of a double insulated tool can result in . CIRCULAR SAW...
Parts List - Page 3
...1 Roll Pin 1 Lower Blade Guard Support Assembly (Inc. Key No. 19 1 Screw (M4 x 16 mm, Pan Hd 4 Torsion Spring 1 Lower Blade Guard 1 Retaining Ring 1 Inner Flange Bushing 1 Outer Blade Washer 1 Blade Screw (5/16-18 x 9/16 in all correspondence regarding your CIRCULAR SAW or when ordering parts. CIRCULAR SAW - KEY PART NO. RYOBI 7-1/4 in 1 Laser Label 1
Edge Guide Kit (Optional 1 Dust...
Parts List - Page 4
LASER ASSEMBLY
RYOBI 7-1/4 in. MODEL NUMBER CSB134L
CIRCUIT BOARD ASSEMBLY
BLACK
MICRO SWITCH
BLACK
BLACK
SWITCH
BRUSH
ASSEMBLY
RED
BLACK
RED MOTOR
WHITE
WHITE
WHITE
POWER CORD
WIRE NUT
WIRING DIAGRAM
4 CIRCULAR SAW -
Ryobi CSB134L Reviews
We have not received any reviews for Ryobi yet.