Ryobi TS1142L Support and Manuals
Get Help and Manuals for this Ryobi item
View All Support Options Below
Free Ryobi TS1142L manuals!
Problems with Ryobi TS1142L?
Ask a Question
Free Ryobi TS1142L manuals!
Problems with Ryobi TS1142L?
Ask a Question
Popular Ryobi TS1142L Manual Pages
User Manual - Page 5
... securely retighten the blade bolt.
If any part of this ever occur, stand clear and allow the saw blade to stop . e) Never reach around saw blade. Refer to them these instructions also.
5 SPECIFIC SAFETY RULES
Never hand hold a workpiece that is too small to be replaced only by the manufacturer or by the carrying...
User Manual - Page 8
GLOSSARY OF TERMS
Anti-Kickback Pawls (radial arm and table saws) A devise which, when properly installed and maintained, is designed to stop the workpiece from being kicked back toward the front of the spinning blade.
Dado Cut (table saws and compound sliding miter saws) A non-through cut without the workpiece being done. Gum A sticky, sap-based...
User Manual - Page 10
... provides protection from each side of this operator's manual as well as the saw is located in .
FEATURES
KNOW YOUR COMPOUND MITER SAW
See Figures 1 - 4. wide, depending upon the angle at 0° and 45°.
LASER GUIDE
For more accurate cuts, a laser guide is made . MITER FENCE
The miter fence on both the left and right side of...
User Manual - Page 12
LOOSE PARTS LIST
The following items are included with your compound miter saw:
Miter Saw Dust Bag Work Clamp
Blade Wrench AAA Batteries (2) Rear Bracket/Carrying Handle
DUST BAG
WORK CLAMP
AAA Batteries
Blade Operator's Manual
miter saw
blade
blade wrench
rear bracket/ carrying handle
Fig. 6
WARNING:
The use of ...
User Manual - Page 13
....
Do not discard the packing material until the parts are damaged or missing do not operate this manual.
If any parts on this miter saw to prevent tipping if the saw arm is factory set aside.
Slide the bracket in the openings on the saw to comply could result in personal injury. Use of the...
User Manual - Page 14
...miter saw base for this warning can result in serious personal injury. blade is the maximum blade capacity of the saw base, lock washers, hex nuts, and the thickness of these locations for hole patTern Spindle Lock Button
mounting surface
Fig. 8
Fig. 9
14 Either of the workbench. Tighten all four bolts securely. To Install/replace...stand, the saw arm. ... the saw is ... the saw . ...
User Manual - Page 16
...miter saw. INSTALLing BATTERIES IN LASER
See Figure 13. Remove screw from creeping toward the saw table base. Rotate the knob on the work clamp provides greater control by clamping the workpiece to polarity indicators inside the battery compartment. Replace... install, squeeze the two metal clips to making the cut. Remove cover and set aside. Install two ...
User Manual - Page 18
...: Make sure that the square contacts the flat part of the saw blade, not the blade teeth. The edge of the square and the saw blade should be necessary to loosen the indicator screws and reset them to the miter table. Place one on the miter table. Slide the other leg of the square...
User Manual - Page 27
... 33. Recheck blade-to heed this manual.
If the blade is play in the pivot joints, have been made at both 0° and 45° angles.
Bevel Pivot Adjustment
The compound miter saw should rise completely to the up position by itself.
If the saw repaired by tightening or loosening the positive...
User Manual 2 - Page 1
COMPOUND MITER SAW
MODEL NUMBER TS1142L REPAIR SHEET RYOBI 7-1/4 in.
User Manual 2 - Page 2
COMPOUND MITER SAW - 30 28 27
FIGURE A
RYOBI 7-1/4 in. MODEL NUMBER TS1142L
25 24
26
1
3
6 7 12 9 10 11
14
23
2
4
7
5
6
8
13 15
16 17 18
8 6
19
21
22
20
65
29
63
59 60
64
61
62
...
User Manual 2 - Page 3
Always mention the model number in all correspondence regarding your 7-1/4 in . COMPOUND MITER SAW - COMPOUND MITER SAW or when ordering parts. Key Nos. 50 and 52 1 Ball Bearing (608 1 Baffle 1 Screw (M4 x 45 mm 2 Washer (OD8 x ID4 x 1t 2 Field 1 Motor Housing 1 Warning Label (English 1 Brush Cover 2 Brush 2 Brush Holder 2 Set Screw (M5 x 8 mm, Soc.
Hd 2 Upper Blade Guard...
User Manual 2 - Page 4
MODEL NUMBER TS1142L
13
8
11
10 9
12
14 15 58
17
18
7 22
21 15 20
19 23 24
6 5 4 3
16
2
29
2
1
28 23
26 22
23 24
27
57
22
23 24
30
31
24
32
22 23 24
25
33
35
34 41
53 36 37 38
51 54
56 52
39 40 50
55
49
40
42
45 46
43 44
47
FIGURE B
48 4 COMPOUND MITER SAW - RYOBI 7-1/4 in.
User Manual 2 - Page 5
COMPOUND MITER SAW or when ordering parts. Key No. 40 1
17
089240003070 Pivot Pin 1
48
089240003006 Bolt (M8 x 20 mm, Hex Hd 1
18
089240003054 Lock Pin Cap 1
49
089240003008 Detent Spring 1
19
089240003053 O-Ring 1
50
089240003007 Steel Ball (8 mm 1
20
089240003052 Spindle Lock Pin 1
51
089240003702 Carry Handle Assembly (Incl. MODEL NUMBER TS1142L
The model number ...
User Manual 2 - Page 6
RYOBI 7-1/4 in. COMPOUND MITER SAW - MODEL NUMBER TS1142L
YELLOW LEAD
BRUSH ASSEMBLY
BRUSH ASSEMBLY
YELLOW LEAD
MOTOR
POWER CORD
SLEEVE
BROWN LEAD
YELLOW LEAD
WHITE LEAD
BLACK LEAD
SWITCH
WIRING DIAGRAM
6
Ryobi TS1142L Reviews
We have not received any reviews for Ryobi yet.