Ryobi TC401 Support and Manuals
Get Help and Manuals for this Ryobi item
Popular Ryobi TC401 Manual Pages
User Manual 2 - Page 3
...KEY PART NO. NUMBER DESCRIPTION
QTY
Wheel Bolt (M6 x 18 mm, Special Left-Hand Threads)........1 Outer Wheel Washer 1 Cutting Wheel (4 in . WET/DRY TILE SAW - Key Nos. 36-37)...1 GFCI Plug Assembly 1 Bend Relief 1 Water Supply ... Clamp 1 Screw (M4.2 x 14 mm 2 Power Cord Assembly (Inc. MODEL NUMBER TC401
The model number will be found on a label attached to the motor housing.
User Manual 2 - Page 4
MODEL NUMBER TC401
Brush Assembly
Brush Assembly Black Lead
White Lead
Black Lead
Switch
Motor
Black Lead
White Lead
Black Lead
Power Cord
WIRING DIAGRAM
4 RYOBI 4 in. WET/DRY TILE SAW -
Operation Manual - Page 2
...repaired before making any adapter plugs with the power tool or these are doing and use any adjustments, changing accessories, or storing power tools. Water...repaired...moving parts....protected supply. Cluttered...instructions...parts...part of dust extraction and collection facilities, ensure these instructions to your hair, clothing, and gloves away from heat, oil, sharp edges, or moving parts...
Operation Manual - Page 3
...install an undamaged wheel. Just because an accessory can break and fly apart.
Wheels must be pulled into the spinning wheel.
Never lay the power tool down until the accessory has come to follow Maintenance instructions... repair person using only identical replacement parts....during this manual. The ... flanges support the wheel...personal protective equipment. SERVICE
Have...
Operation Manual - Page 4
...snagged or pinched by taking proper precautions as the specific potential hazards related to remove the wheel from water and electricity.
4 - Following this rule will draw...INSTRUCTIONS FOR ABRASIVE CUTTING-OFF OPERATIONS
Regularly clean the power tool's air vents. The motor's fan will reduce the risk of serious personal injury.
Protect your nearest authorized service...
Operation Manual - Page 5
... condition. SAFETY INSTRUCTIONS FOR ABRASIVE CUTTING-OFF OPERATIONS
Check damaged parts. Check for an extension cord 25 feet or less in loss of the tool, a guard or other conditions that is in doubt, use this tool, loan them to determine that it must be properly repaired or replaced by an authorized service center to...
Operation Manual - Page 6
Proper interpretation of injury, user must read and understand operator's manual before using this product .
V A Hz W min
no load Double-insulated ... avoided, will result in serious personal injury. Please study them and learn their meaning. Read Operator's Manual
To reduce the risk of these symbols will allow you to properly ground can result in electrocution.
SYMBOLS...
Operation Manual - Page 7
...internal insulation. Always use an extension cord that it for repair.
GFCI plugs do so can be sure to use original factory replacement parts when servicing. WARNING:
Do not operate tool without GFCI intact. ... injury. If the product does not operate when plugged into an outlet, double-check the power supply. If the cord is intended to do not use , press the reset button each...
Operation Manual - Page 8
... wheel Arbor 5/8 in .
Before use of this operator's manual as well as usable for extended periods of time. Dry...dripping onto the outlet or plug. WATER SUPPLY KIT
For wet tile cutting, install the water supply kit and connect to the outlet. ...outlet.
FEATURES
PRODUCT SPECIFICATIONS
Wheel Diameter (Included 4 in .
Disconnect the fuse or circuit breaker that part of the cord below...
Operation Manual - Page 9
... turn the water supply on /off , attach the faucet
adaptor to install the water supply kit. WARNING:
A 4-3/8 in serious personal injury. Do not use cutting wheels rated less than the no load speed of this product with this product until assembly is the maximum wheel capacity of this tool.
WARNING:
If any parts are replaced. Larger wheels...
Operation Manual - Page 10
... securely all missing or damaged parts are dull or badly worn. WARNING:
Since wheel is sufficient to engage with side shield marked to do so will place a heavy load on underside of the water supply and onto the inner flange bushing. WARNING:
If inner flange bushing has been removed, replace it engages.
Keep your...
Operation Manual - Page 11
... the cut to prevent it replaced before
beginning your left. Support the workpiece near the cut. Clamp the workpiece securely so that the workpiece will
not move during a cut . If wet cutting is desired, turn the water supply valve to -mark, place masking tape on the part of cut before using a marker...
Operation Manual - Page 12
... the rest of the saw. Rotate the base until you reach the desired angle setting
on both sides of the material.
Secure the workpiece. If wet cutting is desired, turn the water supply valve to
start water flow. Depress the switch trigger to start the saw. Let the cutting...
Operation Manual - Page 13
... be damaged by an authorized service center in serious personal injury.
Replace both brush assemblies when
either ...done by their use only identical replacement parts. If operation is equipped with plastic parts. Electric tools used on these ...with ANSI Z87.1 during product operation. POWER SUPPLY CORD REPLACEMENT
If replacement of carbon remaining. English
WARNING:
Always wear...
Ryobi TC401 Reviews
We have not received any reviews for Ryobi yet.