Ryobi P552K Support and Manuals
Get Help and Manuals for this Ryobi item
Popular Ryobi P552K Manual Pages
Operation Manual 1 - Page 2
...instructions and cautionary markings in
use this tool, loan them to the cord or charger could result in contact with ANSI Z87.1. They contain chemicals that it will reduce the risk of fire and electric shock.
Take it to an authorized
serviceman when service or repair...replaced by an authorized...ALL INSTRUCTIONS. Following this manual,... or moving parts or otherwise subjected...
Operation Manual 1 - Page 4
...Screws should be installed so that is not properly and completely assembled or with damaged or missing parts could result in... possible problems. Therefore, you careless. DO NOT insert another battery.
This is normal and does not indicate a problem.
... battery pack and charger to your nearest repair center for service or replacement. Latches should charge them clear to inflict...
Operation Manual 1 - Page 5
..., try charging a different battery.
• If a different battery charges normally, dispose of the pack that received the Error (see your battery pack manual for instructions). • If a different battery also indicates Error, the charger should be replaced. CHARGING A COLD BATTERY PACK
A cold battery pack may be placed directly onto the charger port but charging will...
Operation Manual - Page 3
...not using only identical replacement parts. To reduce the ...SPECIFIC SAFETY RULES
Miter saws are too small to fire or excessive temperature. If supporting... explode in the instructions. Abrasive dust causes moving parts such as a pilot...your power tool serviced by the manufacturer. SERVICE
Have...repair person using your hand is placed too close to the saw to support...
Operation Manual - Page 4
... Unrestrained or moving parts to free the jammed material. holding the workpiece to support the workpiece and... cut, causing the blade to them these instructions. Workpieces longer or wider than the table ... change the bevel or miter angle setting, make certain that is wider or...not use the saw blade while cutting. MITER SAW SPECIFIC SAFETY RULES
The workpiece must not be ...
Operation Manual - Page 5
... to any way, or should have damaged, missing, or failed parts replaced before resuming operation.
Always turn the motor switch on tool. ADDITIONAL SAFETY RULES
Use the proper extension cord. Use only a cord heavy enough to install the proper outlet. Repair or replace a damaged or worn cord immediately. This plug will cause a drop...
Operation Manual - Page 9
...the other end is being made.
thick or 4-1/4 in this operator's manual as well as a knowledge of the saw at 0°, 15°... are for bevel cuts. Use the hex key end when installing or removing blade and the phillips end when removing or loosening...2
REAR BRACKET/CARRYING HANDLE
See Figure 2. English
Use the laser guide switch to lock the saw arm by depressing the lock pin.
...
Operation Manual - Page 12
...specific procedures explained in this warning can result in serious personal injury.
If shipping has influenced the settings, refer to make sure that could cause serious personal injury, always remove the battery pack from the tool when assembling parts. WARNING:
To prevent accidental starting any parts are replaced..., read operator's manual and follow the instructions for mounting to ...
Operation Manual - Page 17
...in good operating condition. To adjust the position of the laser guide line, refer to the Adjustments section later in figures 16 ...of the square against the flat part of saw . Practice will be parallel as shown in this manual show points being made in ...miter table.
Loosen bevel lock knob and set saw arm at 0° bevel (blade set 90° to miter table). SQUARING THE BLADE ...
Operation Manual - Page 21
...the fence. See Figures 32 - 33.
When cutting long pieces of lumber or molding, support the opposite end of saw handle firmly. Allow several seconds for the blade to reach maximum speed.
... of the cutting operation just to make sure that no problems will occur when the cut is made with the miter table set at some angle other suitable clamp to secure the workpiece when...
Operation Manual - Page 22
...set at an angle between 0° and 45°.
Pull out the lock pin and lift saw arm to the left to the workpiece. See Figures 32 - 33.
When cutting long pieces of lumber or molding, support...arm to its full height.
Lift the miter lock lever to make sure that no problems will seat itself in one hand and secure it against the fence, the board could collapse on...
Operation Manual - Page 23
...molding, support the opposite end of the stock with a roller stand or with a work surface level with the edge of miter and bevel settings are interdependent with sloping sides.
Care should be set from...in scrap material before making compound miter setups due to the correct bevel angle.
This type of the two angle settings. The first angle setting should always be tilted to the ...
Operation Manual - Page 24
... the blade out of the cutting operation just to secure the workpiece when possible.
TO SUPPORT LONG WORKPIECES
See Figure 30. Supports, roller stand, or work clamp, C-clamp, or other suitable clamp to make sure that no problems will occur when the cut is made.
Grasp the saw , perform a dry run of...
Operation Manual - Page 28
... necessary and periodically check the parts alignment to make sure that ...repaired by itself .
If the saw arm does not raise by at your nearest authorized service... center.
TRAVEL PIVOT ADJUSTMENT
The saw arm should bevel easily by turning the knob
counterclockwise.
Square the blade to the miter table as described in the Assembly section of this manual...
Parts Diagram - Page 5
P552
The model number will be found on a label attached to the motor housing. Hd 2
KEY PART
NO. Hd 2 Blade Screw Label 1
NOT SHOWN: 991000873 1-10-17 (Rev:01)
Operator's Manual
5
Hd 1 Bevel Pointer 1 Screw (M4 x 8 mm, Pan Hd 1 Screw (M8 x 14 mm, Soc. Key Nos. 60 and 64 1 No Hands Label 3 Work Clamp...
Ryobi P552K Reviews
We have not received any reviews for Ryobi yet.