Ryobi P212 Support and Manuals
Get Help and Manuals for this Ryobi item
Popular Ryobi P212 Manual Pages
English Manual - Page 1
...
OPERATOR'S MANUAL
TORQUE IV™ 1/2 in., 18 VOLT HAMMER DRILL 2-SPEED
P211
BATTERIES AND CHARGERS SOLD SEPARATELY
Your hammer drill has been engineered and manufactured to our high standard for your purchase. WARNING: To reduce the risk of rugged, trouble-free performance. Thank you years of injury, the user must read and understand the operator's manual before...
English Manual - Page 2
... the date of two years from misuse, abuse, neglect, alteration, modification or repairs by other than those specifically stated in any malfunction, failure or defects resulting from the date of batteries, power tool accessories are limited to you .
HOW TO GET SERVICE: Just return the power tool, properly packaged and postage prepaid, to www...
English Manual - Page 3
... parts.
If devices are provided for your mains-operated (corded) power tool or battery-operated (cordless)...tools that have the power tool repaired before making any adapter plugs with...turn it on a ladder or unstable support. Keep your body is earthed or grounded... SAVE THESE INSTRUCTIONS
WORK AREA SAFETY
Keep work to operate the power tool. MODEL P211
BATTERY PACK (P100...
English Manual - Page 4
... serviced by an authorized service center to avoid risk.
4 This will reduce the risk of unauthorized parts or failure to noise can cause personal injury.
Hold power tools by insulated gripping surfaces when performing an operation where the cutting tool may be replaced only by the manufacturer or by a qualified repair
person using your battery...
English Manual - Page 5
... serviceman when service or repair is properly wired and in electric shock, fire and/or serious personal injury.
Before using battery charger, read all instructions and cautionary... tool. Replace damaged cords immediately.
Make sure cord is large enough for AC ampere rating of charger as specifically designated on battery charger, battery, and product
using battery.
3. come...
English Manual - Page 7
...We recommend Wide Vision Safety Mask for repair. Indicates a potentially hazardous situation, which is marked to the nearest AUTHORIZED SERVICE CENTER for use only identical replacement parts. SERVICE
Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. SAVE THESE INSTRUCTIONS
7 SYMBOL SIGNAL
DANGER: WARNING: CAUTION: CAUTION:
MEANING...
English Manual - Page 10
... paint Hammer drilling in serious personal injury. Remember that a careless fraction of or below normal temperature range.
Yellow and Green LEDs on = Deeply discharged or defective battery pack.
No LED on = When battery pack is inserted into your nearest service center for service or replacement. Return the charger and battery to possible serious personal...
English Manual - Page 11
... the first time they are shipped in a low charge condition to prevent possible problems. Therefore, you should be replaced.
After normal usage, a minimum of 1 hour of the charger comes on . NOTE: If the charger does not charge the battery pack under normal circumstances, return both yellow and green LEDs come on . Allow...
English Manual - Page 12
... with the bottom of the drill and latches into place and the battery pack is secured on , return battery pack to recharge. NOTE: This situation only occurs when continuous use of the tool causes the batteries to your nearest Ryobi Authorized Service Center for approximately 30 minutes before beginning operation. TO INSTALL BATTERY PACK
See Figure 4. Lock...
English Manual - Page 13
...drill to LOCK (tighten) or UNLOCK (release) the drill bit. VARIABLE SPEED
The variable speed switch trigger delivers higher speed and torque with increased trigger pressure and lower speed with the rotating drill bit. With the drill... of rotation selector is a normal part of the switch trigger for extended ...come to the right of rotation.
Setting the switch trigger in use . INTERNAL...
English Manual - Page 15
...heads, threads, workpiece, etc. MODE DRILL MODE
(TORQUE ADJUSTMENT NOT ACTIVE)
DRIVE MODE
2/HIGH 1/LOW 2/HIGH
HAMMER MODE
TORQUE ADJUSTMENT
See Figure 10. If the torque is adjusted by 1-1/2 in . The torque is greater when the torque adjustment ring is set on a lower setting. The torque is less when the torque adjustment ring is set on a higher setting. SPEED 1/LOW 2/HIGH 1/LOW...
English Manual - Page 20
... rechargeable batteries.
WARNING:
Do not at a Ryobi Authorized Service Center.
Also, never touch both terminals with metal objects and/or body parts as short circuit may result in this tool is dusty, also wear a dust mask. All other parts should be replaced at any other parts may be repaired or replaced by their use only identical Ryobi replacement parts. The batteries in...
English Manual - Page 22
... in the space provided below.
• HOW TO ORDER REPAIR PARTS
When ordering repair parts, always give the following information:
• MODEL NUMBER
P211
• SERIAL NUMBER
Ryobi® is a registered trademark of Authorized Service Centers.
• MODEL NO. OPERATOR'S MANUAL
TORQUE IV™ 1/2 in., 18 VOLT HAMMER DRILL 2-SPEED
P211
WARNING:
Some dust created by power sanding...
Repair Sheet - Page 3
...GUIDE ROD 1
39
513665001 GUIDE ROD SUPPORT 1
40
641028001 PRESS PLATE 1
41 300067447 HANDLE ASSEMBLY 1
983000749 OPERATOR'S MANUAL... TORQUE ...PARTS LIST
KEY NO. PART NUMBER
DESCRIPTION
QTY.
1
6613402
* SCREW (SPECIAL 1
2
690032024 1/2 in all correspondence regarding your Hammer Drill or when ordering repair parts. May Be Purchased Locally
RYOBI...
Repair Sheet - Page 4
RYOBI 1/2 in. (13 mm) HAMMER DRILL- MODEL NUMBER P211
MOTOR
BLACK LEAD
RED LEAD
SWITCH
RED LEAD CONTACT
PLATE HOLDER
WIRING DIAGRAM
BLUE LEAD YELLOW
LEAD BLACK LEAD
BLACK LEAD
Ryobi P212 Reviews
We have not received any reviews for Ryobi yet.