User Manual
Page 4
...- Do not use , before performing the maintenance and adjustment procedures described in use only. DANGER 25. : Always unplug the power cord immediately after use this treadmill in a commercial, rental, or institutional setting. 27. Over exercising may result in the storage position. 23. Never insert any...lbs. (20 kg) to do so by an authorized ser- Never remove the motor hood unless instructed to raise, lower, or move the treadmill until it is running. vice representative only. 26. This treadmill is intended for home use . (See the drawing on page 5 for the ...
...- Do not use , before performing the maintenance and adjustment procedures described in use only. DANGER 25. : Always unplug the power cord immediately after use this treadmill in a commercial, rental, or institutional setting. 27. Over exercising may result in the storage position. 23. Never insert any...lbs. (20 kg) to do so by an authorized ser- Never remove the motor hood unless instructed to raise, lower, or move the treadmill until it is running. vice representative only. 26. This treadmill is intended for home use . (See the drawing on page 5 for the ...
User Manual
Page 26
... back in . SYMPTOM: The displays of this manual. c. Check the power switch located on page 15. If the displays are still lit, see THE INFORMATION MODE on page 23 to be used if the treadmill is plugged in . Carefully pivot the Motor Hood (65) off the demo mode, hold down the Stop button... for five minutes and then press the switch back in , make sure that applies, and follow the steps listed. d. If the treadmill still will not run, please see page 15). SYMPTOM: The power does not turn on...
... back in . SYMPTOM: The displays of this manual. c. Check the power switch located on page 15. If the displays are still lit, see THE INFORMATION MODE on page 23 to be used if the treadmill is plugged in . Carefully pivot the Motor Hood (65) off the demo mode, hold down the Stop button... for five minutes and then press the switch back in , make sure that applies, and follow the steps listed. d. If the treadmill still will not run, please see page 15). SYMPTOM: The power does not turn on...
User Manual
Page 27
Turn the Pulley until the walking belt is about 1/8 in the console, press one of the Incline buttons. Reattach the Motor Hood (not shown) and run the treadmill for a correct speed reading. This will automatically rise to the maximum incline level and then return to 7 cm) off the walking platform. a. ... of the walking belt 2 to check for a few seconds, reinsert the key. Top View 52 49 14 50 1/8 in the power cord, insert the key, and run the treadmill for a few minutes to 3 in . Be careful to do so by an authorized service representative. Then, plug in . While...
Turn the Pulley until the walking belt is about 1/8 in the console, press one of the Incline buttons. Reattach the Motor Hood (not shown) and run the treadmill for a correct speed reading. This will automatically rise to the maximum incline level and then return to 7 cm) off the walking platform. a. ... of the walking belt 2 to check for a few seconds, reinsert the key. Top View 52 49 14 50 1/8 in the power cord, insert the key, and run the treadmill for a few minutes to 3 in . Be careful to do so by an authorized service representative. Then, plug in . While...
User Manual
Page 30
... Screw #8 x 1/2" Ground Screw 5/16" Star Washer 3/8" Nut 3/8" Star Washer #8 x 3/4" Tek Screw Idler Roller Screw 3/8" x 1 1/2" Bolt 3/8" x 1 3/4" Wheel Bolt #8 x 1 3/4" Screw #8 x 7/16" Screw 5/16" Motor Screw 1/2" x 2 1/4" Bolt 3/8" x 1" Bolt 5/16" x 1 3/4" Shoulder Bolt 1/4" x 1" Screw #8 x 1" Screw 1/4" Washer 1/4" Lock Washer #8 x 3/4" Belly Pan Screw 3/8" x 2" Hex Head Bolt 5/16" Flat Washer 5/...32" Hex Key Motor Hood Hood Accent Incline Frame Spacer Incline Motor Sensor Incline Motor Incline Frame Frame Spacer Controller Controller Plate Hood Post Power Switch Power Cord Grommet Belly Pan...
... Screw #8 x 1/2" Ground Screw 5/16" Star Washer 3/8" Nut 3/8" Star Washer #8 x 3/4" Tek Screw Idler Roller Screw 3/8" x 1 1/2" Bolt 3/8" x 1 3/4" Wheel Bolt #8 x 1 3/4" Screw #8 x 7/16" Screw 5/16" Motor Screw 1/2" x 2 1/4" Bolt 3/8" x 1" Bolt 5/16" x 1 3/4" Shoulder Bolt 1/4" x 1" Screw #8 x 1" Screw 1/4" Washer 1/4" Lock Washer #8 x 3/4" Belly Pan Screw 3/8" x 2" Hex Head Bolt 5/16" Flat Washer 5/...32" Hex Key Motor Hood Hood Accent Incline Frame Spacer Incline Motor Sensor Incline Motor Incline Frame Frame Spacer Controller Controller Plate Hood Post Power Switch Power Cord Grommet Belly Pan...