Panasonic AJSD955BP - DVC PRO50 DECK Support and Manuals
Get Help and Manuals for this Panasonic item
View All Support Options Below
Free Panasonic AJSD955BP manuals!
Problems with Panasonic AJSD955BP?
Ask a Question
Free Panasonic AJSD955BP manuals!
Problems with Panasonic AJSD955BP?
Ask a Question
Popular Panasonic AJSD955BP Manual Pages
AJSD930B User Guide - Page 2
... installation instructions ...digital device, pursuant to comply with Part ...SETTING INSIDE THE UNIT TO QUALIFIED SERVICE PERSONNEL. NO USER SERVICEABLE PARTS INSIDE. Please contact either a local or foreign Panasonic authorized service center for U.S.A. CAUTION:
Even when the Power Switch is not intended for assistance in a commercial environment. The lightning flash with the instruction manual...
AJSD930B User Guide - Page 3
Contents
Introduction 3
Features 4
Parts and their functions 5 Front panel 5 Display panel 11 Rear panel 13
Connections 15
Tapes 17
Jog/Shuttle 18
Manual editing SD955B 19
Preroll SD955B 19
Automatic editing (deck-to-deck) SD955B 20 Switch settings and adjustments 20 Selecting the editing mode 21 Registering the edit points 21 Checking and previewing...
AJSD930B User Guide - Page 4
...-based setup The setup settings, which are conducted prior to the internal time code, external time code input...setting (setup menu item No. 070) that do not support the recording and playback of UMID information is connected to be used with a consumer digital camera... serial digital interface is provided as standard.
Digital slow motion/jog dial Panasonic's original digital slow-motion...
AJSD930B User Guide - Page 5
... : AES/EBU digital signals CH3 : SDI input digital signals CH4 : Analog input signals
O It is used in the order of DVCPRO50 (50 Mbps) format tapes. VIDEO: Each time the VIDEO button is pressed, the input video signal selection is switched in the unit are displayed here. Example:
Settings AUDIO button USER SET Setup menus No...
AJSD930B User Guide - Page 8
...registered that was pressed is registered as the setup menu No. 313 (AUTO ENTRY) setting. H TRIM buttons SD955B These buttons are ... increments is selected. to locate where a transmission or manual editing starts on the tape.
K AUTO EDIT button ...pressed after points have been registered, automatic editing is registered.
Parts and their functions
Front panel
L
JKIHE F
ON
POWER
...
AJSD930B User Guide - Page 9
Parts and their functions
Front panel
M
ON
POWER
OFF
DVCPRO
DVCPRO 50
DV
METER FULL/FINE
L MONITOR SELECT
R
HEADPHONES
MONITOR MIX
A VOL SELECT
INPUT SELECT PREVIEW/PREVIEW AUTO EDIT PREROLL
VIDEO AUDIO
COUNTER ASSEM VIDEO CUE TC STAND BY PLAYER RECORDER
RESET CH1 CH2 CH3 CH4
A IN
INSERT TRIM
A OUT
SET... of digits whose display is flashing is set to...selected using setup menu No...
AJSD930B User Guide - Page 11
...SET SDI SDTI/1394 SG
: Analog audio signals : Digital audio signals : Recording audio signal selection : Serial digital audio signals : Compressed digital signals (option) : Internal reference signals
9 Channel condition lamps These lamps light to indicate the error...lights when the 625 interlaced TV system is displayed here. Parts and their functions
Display panel
1
2
3
4
6 ...setting setup...
AJSD930B User Guide - Page 13
... and video signals that comply with parallel run operations For loop-through this VTR, set the termination switch to these connectors. For termination at this connector. Parts and their functions
Rear panel
1
AC IN
SIGNAL GND
2 3 4 5 6 7 8 9: ;
The digital audio signals which inputs the reference video signal be used to be used can be...
AJSD930B User Guide - Page 14
...selected using setup menu No. 00 (WFM SEL).
Parts and their...
OUT
L
3 (SUPER)
OPTION
SDTI
IN
OUT
CH3
CH4
MON
R
1
2
SERVICE ONLY
> ?@ A
BC D
< Fan This fan is to be operated by... Whether the superimposing is to be set ON or OFF is installed in order to operate the VTR.
... is used when the VTR is used to this VTR, digital data can be connected to cool down the VTR.
D...
AJSD930B User Guide - Page 15
...Set the CONTROL switch on the front panel to LOCAL. Video and audio output may be disturbed when the reference video signal is not input, so it is recommended that a system which inputs the reference video signal be used.
15 Reference signal generator
Remote control signal (9 pin)
Digital...R
1
2
SERVICE ONLY
Recorder
AC ...SERVICE ONLY
To video monitor device
To audio monitor device
Digital...
AJSD930B User Guide - Page 19
...position where the button was pressed for the period of time which was set by setup menu No. 000 (P-ROLL TIME), and it is rewound from the edit IN point for the...preroll operation.
OWhen the IN point has not been registered, it then stops. OThe time code or CTL must be edited. Manual editing SD955B
1 Select the editing mode. INSERT: Insert editing is performed in this mode....
AJSD930B User Guide - Page 35
...displayed in which the tape is to be played back.
0000 MANUAL : The format complies with the setting of this setting is changed so that the
characters are to be disturbed until the...complies with the
SUPER OFF/ON setting.
Setup menus
USER menu
No./Item
Description
009
This sets the position of the characters on the
horizontal plane for the time code and other
CHARA V-POS super...
AJSD930B User Guide - Page 40
... (N-STD) setting when
video or audio trouble occurs with signals from
laser discs or a satellite.
The same type of the VTR using a controller which does not have a digital audio edit ...N-STD :
Non-standard signals are automatically cleared. The underlined items indicates the initial setting.
40 Setup menus
USER menu
No./Item
Description
301 SD955B IN/OUT DEL
This selects the operation...
AJSD930B User Guide - Page 56
... FREE RUN mode, the time code begins to the 32-bit (8-digit) data frame among the time code signals which was set the start flashing. TCR 00 : 07 : 04 : 24
t
t
t
t
Hours Minutes Seconds Frames
User bit
"User bit" refers to advance. 6 Proceed with the recording or editing.
2 Select "TC" using setup menu No. 503 (TCG...
AJSD930B User Guide - Page 70
Hardware specifications
External interface specifications
O Connector specifications Connector: D-SUB 25-pin (crossover cable supported)
Pin No. 1 2 3 4 5 6 7 20
Signal
Description
FG RXD TXD CTS RTS DTR SG DSR
Protective ground (Frame ground)
Received data (Data is sent to PC.)
Transmitted data (Data is returned depends on pages 73, 74.)
$ Conditions for setup menu item No. 209 "RETURN...
Panasonic AJSD955BP Reviews
We have not received any reviews for Panasonic yet.