Oki GL408e Support and Manuals
Most Recent Oki GL408e Questions
Popular Oki GL408e Manual Pages
GL408e/GL412e User's Guide - Page 25
... the list of logical printer name as lp, sjis, euc. It requires a driver (shipped with RFC854. GL408-412e Operator Manual
3-11
PN: 9001163A Printer Connector Cable Host Power Supply Power Consumption
SPECIFICATIONS
USB Type B Plug 10 feet (3 m) maximum Windows 2000 or above . Printer status is shipped with each printer that has the interface installed) that must be printed...
GL408e/GL412e User's Guide - Page 51
...Printer Configuration
DGL EMULATION MODE
This chapter provides the programming sequences required to the appropriate emulation chart. Error Handling Vert. Switch (V) Sensor Cmd (e,r) Format Attr. (A)
Active Yes*
Character Set PC-8 CP 437*
Euro Character 128*
Control Codes.... Switch (V) Process*
Sensor Cmd (e,r) Process*
Format Attr. (A) Process*
GL408-412e Operator Manual
Figure 4-12, DGL ...
GL408e/GL412e User's Guide - Page 54
... is enabled within the
Advanced Mode
ENTER
DIAGNOSTICS
Priority Setting Printer Tests Test Count Software Build Hex Dump Mode Print Error Log Clear Error Log Flash Installed DRAM Installed Ptr On Time Printer Usage PrintHead Usage Head On Time Reset Head Data PrintHead Usage Head Type Head Voltage
ENTER
Priority Setting Command*
Printer Tests Checkerboard*
Software Build XXXXXX VX.XXX
Hex...
GL408e/GL412e User's Guide - Page 60
... barcodes. The top-right corner of the image is identical to parameters 1 and 2 of resolution used to be determined.
• Portrait - Portrait - This setting changes the horizontal base reference point for calculations can be fine adjusted by this menu between -100 and +100. factory default. UPC/EAN bar codes are printed with older SATO printer models...
GL408e/GL412e User's Guide - Page 62
The Display Ribbon option must be set to Gap, the printer will subtract the Gap Length value (in menu.
• 3 Labels -
The Sensed Distance value derived from the Sensed Distance value obtained when the Auto or Manual Calibrate was performed. Note: When Set Label Length = Automatic and the label sensor is set using the tear bar. By controlling how much blank...
GL408e/GL412e User's Guide - Page 63
...menu of a specific configuration. This menu screen permits a particular print job to be saved unless the exisitng configuration has first been deleted.
This menu set allows the selection...printer can store up to eight unique configurations to be saved.
The factory default is enbled, the new configuration will not be lost when the printer is being loaded. GL408-412e Operator Manual...
GL408e/GL412e User's Guide - Page 66
...Manual
4-30
PN: 9001163A Status Port Del Char frm F1s Ld Char from F1s Save Char to F1s Del Char frm RAM Ld Char at PwrUp Del Set frm F1s Ld Set from the printer... may occur after each label printed. • Cut - Only available with cutter asembly installed. • Rewind -
Intensity Sensor Setup Admin User
Media Handling Continuous*
Unit 4: Printer Configuration
ADVANCED MODE (TABLE...
GL408e/GL412e User's Guide - Page 75
... ideal for top-of transitions detected.
GL408-412e Operator Manual
4-39
PN: 9001163A
MENU
Use Label Length Disable*
Threshold Range 50%*
Mark TOF Detect Mark Trail Edge*
MENU
INTERFACES
Unit 4: Printer Configuration
ADVANCED MODE (TABLE 4-3)
DESCRIPTION
Determines if the Label Length value set in the Media Setup menu is used during the calibration process to determine...
GL408e/GL412e User's Guide - Page 109
... actively removed. Storage in decimal format) desired to the host. GL408-412e Operator Manual
4-73
PN: 9001163A Switch (V) Sensor Cmd (e,r) Format Attr. (A)
Active Yes*
Character Set PC-8 CP 437*
Euro Character 128*
Control Codes Standard*
FeedBack Chars Disable*
Default Module RAM*
Unit 4: Printer Configuration
DGL EMULATION MODE (TABLE 4-12) DESCRIPTION
Is the menu selection screen...
GL408e/GL412e User's Guide - Page 118
... Mode. DIAGNOSTICS
Priority Setting Printer Tests Test Count Software Build Hex Dump Mode Print Error Log Clear Error Log Flash Installed DRAM Installed Ptr On Time Printer Usage PrintHead Usage Head On Time Reset Head Data PrintHead Usage Head Type Head Voltage
Priority Setting Command*
Is the menu selection screen for an incoming print job regardless of programming will reflect the...
GL408e/GL412e User's Guide - Page 129
... 5: Troubleshooting
ERROR SIGNALS
DISPLAY
ERROR: OCCURRED: CLEARING QUEUES Please Wait
EXPLANATION
SOLUTION
An interim message diplays while the printer Wait. When the asterisk (*) stops rotating, a
discards host data it is installed on again.
While the message displays, the asterisk (*)
rotates. If the problem persists, contact an authorized customer service representative. SENSOR...
GL408e/GL412e User's Guide - Page 130
... the media sensor is broken between the ribbon rewind Reattach ribbon.
as necessary. If using the cutter, the printer must be set too high Paper Out Thresh is removed) the printer Install the cutter option or change to detect the installed media. cutter upper enclosure is too low.
If the problem persists, contact an authorized customer service representative.
GL408...
GL408e/GL412e User's Guide - Page 134
... is selected.
Ensure the host's peripheral settings are consistent with those being used and perform each end. Ensure the printer is correctly connected at each of the troubleshooting tasks until the problem has been isolated.
Ensure that procedure within this manual for instructions.
Refer to ECP for details. Replace the main circuit board if determined to verify...
GL408e/GL412e User's Guide - Page 136
... of data. The test label is enabled within the
Advanced Mode
ENTER
DIAGNOSTICS
Priority Setting Printer Tests Test Count Software Build Hex Dump Mode Print Error Log Clear Error Log Flash Installed DRAM Installed Ptr On Time Printer Usage PrintHead Usage Head On Time Reset Head Data PrintHead Usage Head Type Head Voltage
ENTER
Priority Setting Command*
Printer Tests Checkerboard*
Software...
GL408e/GL412e Cutter Install Guide - Page 6
... ONLINE mode after saving the new
settings. Figure 2. When completed, go to OFFLINE mode.
3. Simple-Cutter Installation Guide
PRINTER CONFIGURATION FOR CUTTER OPERATION
Once the Label Cutter has been installed, the printer automatically detects it to initialize and go into
ONLINE mode. 2. The cutter is not activated by default, except via the printer driver or via the LCD Menu...
Oki GL408e Reviews
Do you have an experience with the Oki GL408e that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Oki yet.
Earn 750 points for your review!