Netgear XCM8944 Support and Manuals
Get Help and Manuals for this Netgear item
This item is in your list!
View All Support Options Below
Free Netgear XCM8944 manuals!
Problems with Netgear XCM8944?
Ask a Question
Free Netgear XCM8944 manuals!
Problems with Netgear XCM8944?
Ask a Question
Popular Netgear XCM8944 Manual Pages
Command Line Interface CLI User Manual Software Version 11.x - Page 2
... purposes only. See the regulatory compliance document before you for technical support. After installing your device, locate the serial number on the label of the {deny | permit} (IPv6) command. Contact your product before connecting the power supply. For product updates and web support, visit http://support.netgear.com. M5300, M6100, and M7100 Series ProSAFE Managed Switches...
Command Line Interface CLI User Manual Software Version 11.x - Page 4
...Filtering Commands 175 Dual Image Commands 177 System Information and Statistics Commands 178 Switch Services Commands 207 Logging Commands 209 Email Alerting and Mail Server Commands 217 System ... Commands 245 DNS Client Commands 258 IP Address Conflict Commands 263 Serviceability Packet Tracing Commands 264 Support Mode Commands 302 Cable Test Command 305 Power Management Commands 306...
Command Line Interface CLI User Manual Software Version 11.x - Page 54
Code Version
The firmware load target identifier of the switch type. Model Identifier The model identifier for the supported switch type. Management Preference
The management preference value of the switch type. Switch Description The description for the supported switch type. Stacking Commands 54 This index is used when you supply a value for switchindex, the following output ...
Command Line Interface CLI User Manual Software Version 11.x - Page 91
... M5300, M6100, and M7100 Series ProSAFE Managed Switches
permit service
This command sets permit conditions for the management access list based on the source IP address of a packet. Format Mode
permit service service [priority priority] Management access-list configuration
Parameter service priority
Definition Indicates the service type: telnet, ssh, http, https, or snmp. permit priority...
Command Line Interface CLI User Manual Software Version 11.x - Page 92
...update or remove a management ACL when it is the name of the existing management ACL.
Format Mode
deny service service [priority priority] Management access-list configuration
Parameter service priority
Definition Indicates the service...M5300, M6100, and M7100 Series ProSAFE Managed Switches
deny service
This command sets deny conditions for the rule.
deny priority
This command ...
Command Line Interface CLI User Manual Software Version 11.x - Page 372
...for spanning-tree. Per VLAN Rapid Spanning Tree Protocol (PVRSTP) embeds support for this port within the multiple spanning tree instance or in the range of only the root bridge... in increments of 16. If you specify the cost option, the command sets the path cost for this port within a specific multiple spanning tree instance or the common and internal spanning tree instance, depending...
Command Line Interface CLI User Manual Software Version 11.x - Page 373
... this port within a range of multiple instances supported by the switch is a number that multiple spanning tree instance. M5300, M6100, and M7100 Series ProSAFE Managed Switches
no spanning-tree mst instance mstid Global Config
spanning-tree mst priority
This command sets the bridge priority for a specific multiple spanning tree instance. If you specify...
Command Line Interface CLI User Manual Software Version 11.x - Page 655
... (PFC) on the interface. When priority-flow-control is at least one . Use the no -drop priority. In NETGEAR Managed Switch, these priority values must be set to one-to-one no form of -service (CoS) values. priority-flow-control mode
Use the priority-flow-control mode on command in order to carry...
Command Line Interface CLI User Manual Software Version 11.x - Page 656
...mode command to return the PFC mode to the default (off).
Additionally, the dot1pmapping to class of service must configure the same no-drop priorities across the network in Datacenter-Bridging Config mode to enable the...behavior on the selected interface. VLAN tagging needs to be set to one to two lossless priorities can be enabled on the selected priorities.
Up to one.
Software Administration Manual Software Version 11.x - Page 14
... Stack Members 496 Stack Member Numbers 496 Stack Member Priority Values 496 Install and Power-up a Stack 496 Compatible Switch Models 496 Install a Switch Stack 497 Switch Firmware and Firmware Mismatch 498 Upgrade the Firmware 498 Migrate Configuration with a Firmware Upgrade 499 Web Interface: Copy Master Firmware to a Stack Member 499 Stack Switches Using Ethernet Ports and a Stack...
Software Administration Manual Software Version 11.x - Page 302
...Set queue 5 on the outbound side.
CLI: Configure DiffServ for the switch.
(Netgear Switch) #config (Netgear Switch) (Config)#cos-queue strict 5 (Netgear Switch) (Config)#diffserv
DiffServ
302
Software Administration Manual... Managed Switches
DiffServ for VoIP
One of the most valuable uses of service: how to support Voice over IP (VoIP). Diffserv for VoIP in the accompanying diagram:...
Software Administration Manual Software Version 11.x - Page 487
NETGEAR recommends that you schedule the firmware upgrade when no member commend
to reset the model type.
Chassis Switch Management
487
Software Administration Manual For updates where this issue is running .
If an error occurs during code propagation, do not come up, and the show chassis command shows a code mismatch error.
1. After code is successfully loaded on the CLI...
User Manual Software Version 11.x - Page 16
... at downloadcenter.netgear.com, including the following methods:
• Web user interface • Simple Network Management Protocol (SNMP) • Command-line interface (CLI) Each of the following publications: • M6100/M7100/M5300 Chassis Hardware Installation Guide. • M6100/M7100/M5300 Switch Module Installation Guide. • M6100/M7100/M5300 Software Setup Manual. •...
Product Data Sheet - Page 37
... MIB for High Capacity Alarms
RFC 2576 - Integrated Services MIB
FASTPATH Enterprise MIBs supporting switching features
RFC 2233 - QCN (Quantized Congestion Notification)
DCB Capability Exchange Protocol Specification Rev 1.0 DCBX
IEEE 802.1Qaz Draft 2.4 - SNMP-NOTIFICATION-MIB
RFC 1155 - SMI-MIB
RFC 3413 - View-based Access Control Model for IPv6
RFC 6164 - SNMP Community MIB...
Web Management User Guide - Page 392
...users where inbound service policy attachment is In. To configure DiffServ policy settings on the page, click Apply to send the updated configuration to ...service interface is not supported by the platform. To display the page, click QoS DiffServ Advanced Service Interface Configuration.
Lists all the policy names from which you change any of the settings...
Netgear XCM8944 Reviews
Do you have an experience with the Netgear XCM8944 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Netgear yet.
Earn 750 points for your review!